成形模

The preparation of titanium alloy powder's slurries with high solid loading was investigated.

将凝胶注模工艺应用于金属Ti及Ti-6Al-4V合金粉末的坯体成形，研究了高固相含量的Ti粉和Ti-6Al-4V合金粉末的料浆的制备。

A type of new progressive die including blanking, bending and forming is introduced.

介绍了一种新型的落料、弯曲、成形连续模。

By analyzing the forming process to engine bracket lower plate , and introduced the design of bending die,some measures to control spring back were extracted, the spring back problem of engine bracket lower plate was solved.

通过对发动机支架下板成形工艺的分析及其弯曲模结构的介绍，总结了几种控制回弹的措施，解决了发动机支架下板回弹难以解决的问题。

The explicit dynamic code DYNA3D was used to simulate the drawing process of cross member part.

对汽车底盘横梁拉深成形过程进行了数值模拟，对比分析了数值模拟结果与实验结果，同时讨论了凸模的虚拟冲压速度对数值模拟结果的影响。

According to the velocity filed mentioned above, the contour of the drawing die was rationally designed. To prove its applicability and superiority, FEM software, MARC and SUPERFORM, were used to simulate the drawing process of cross tube in "conical die" and "streamlined die".

本文以十字形钢管为研究对象，开展对异型钢管拉拔成形过程研究，首先结合挤压流线理论，设计了&流线型&拉拔速度场模型，这为改善金属流动状态、降低能耗创造了良好条件；紧接着以&流线型&速度场为理论依据，对十字形管拉拔模具的凹模轮廓进行了合理设计。

The shaping course of Fine blanking is very complex. Material forms a local plastic cutting area between punch and bottom die, and brings violent plastic flow under the effect of press stress. The grad of stress and strain is great, and it is an unstable transmutation process that came through an elastic distortion, plastic distortion and cut rupture.

精冲成形过程非常复杂，材料在狭窄的凸、凹模间隙附近形成了局部塑性剪切带，在压应力的作用下产生强烈的塑性流动，应力应变梯度很大，是一个经历弹性变形、塑性变形和剪切断裂的非稳态大变形过程。

After analyzing a large number of typical deep-drawing process design plans, process design knowledge of deep-drawing process is summarized.

在分析了大量的典型拉深件成形工艺方案的基础上总结了拉深件工艺设计知识，并将它们按照冲压件工艺设计过程进行模决化组织。

According to design route of the forming process of drawing with camber die, this software can be divided into 3 modules: the module of the chamber design, the module of process parameters design, the relative diagram of influence factor of limit drawing coefficient.

按照曲面凹模拉深成形工艺的设计路线，软件设计成三个功能模块：曲面凹模型腔设计模块、工艺参数设计模块、极限拉深系数影响因素关系图。

In the open die forging ,the type of flash has great influence on the process of forging.

开式模锻中飞边槽的形式对锻件成形过程的影响较大。

The die set of claim 1 wherein said piercing points comprise a plurality of pyramid shaped structures.

要求 1 的一钢模组在何处说刺骨的点包含被成形结构的一个金字塔的多数。

Singer Leona Lewis and former Led Zeppelin guitarist Jimmy Page emerged as the bus transformed into a grass-covered carnival float, and the pair combined for a rendition of "Whole Lotta Love".

歌手leona刘易斯和前率领的飞艇的吉他手吉米页出现巴士转化为基层所涵盖的嘉年华花车，和一双合并为一移交&整个lotta爱&。

This is Kate, and that's Erin.

这是凯特，那个是爱朗。