成层
- 与 成层 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
As a result, if the iridescence is produced by thin-film interference, not only the thickness of lamellar structure must be defined within a certain nanometer, but also the refractive index need to be different between lamellar structure. In other words, the chemical composition, refractive index and thickness of exsolution lamellae need form to trinity, such as labradorite, albite, andradite and orthoamphibole. If the iridescent color is produced by grating-diffraction, the lamellar structure just needs to be arrayed regularly, the spacing of the edges of lamellar structure needs to be regular and narrow, but not necessarily within the range of the wavelength of visible light, such as shell of abalone, pearl and opal.
薄膜干涉式晕彩不仅要求宝石内部结构层的厚度必须在一定的纳米范围内,而且结构层内部的折射率也必须有所差别,也即,当结构层由两相组分出溶而成,其化学成分、折射率和结构层厚度形成三位一体时,符合薄膜干涉式晕彩,如拉长石、钠长石、石榴石和角闪石;而光栅式衍射晕彩则仅要求结构层排列规则,边缘狭窄但不需要窄到可见光波长范围内,能使入射光的振幅或位相,或两者同时产生周期性空间调制的结构即可,如鲍贝壳、珍珠和欧泊。
-
Finally, based on the fundamental solutions of Biots consolidation of transversely isotropic saturated multi-layered soils, the Fredholm integral equation of second kind for the interaction between transversely isotropic saturated multi-layered soils and rectangular piles is established, the relevant numerical analysis is also carried out.
最后,基于横观各向同性层状饱和地基Biot固结问题的基本解答,建立了横观各向同性层状饱和地基与方形单桩、群桩共同作用问题的第二类Fredholm积分方程,并进行了数值分析与计算;通过将矩形刚性基础基底划分成若干个大小相等的矩形网格,用矩形均布荷载表示网格的基底反力,并利用已获得的横观各向同性层状饱和地基Biot固结问题的基本解来求解每个矩形网格的柔度系数,然后根据刚性基础与层状饱和地基的接触条件和其本身的静力平衡条件,求解分析了横观各向同性层状饱和地基与刚性矩形板的共同作用问题。
-
We have successfully synthesized hydrocarbonbearing inclusions in carbonate at the temperature and pressure of 150 ℃ and 40 MPa, which are near the condition of natural reservoir underground 4 kmAll synthetic hydrocarbonbearing inclusions have been analyzed by microscope and microfluorescence and fourier transform infrared spectroscopyThe results show that the synthesized hydrocarbonbearing inclusions are very similar to those in real reservoirsOur experiments give us four important insights, including:(1) immiscibility of oil and water is the main reason for hydrocarbonbearing inclusions and aqueous inclusions distributed in different fractures;(2) rapid accumulation of oil and gas can be recorded by fluid inclusions;(3) the study of synthetic hydrocarbonbearing inclusions at the temperature and pressure of real reservoir will offer references and standards for the analysis of fluid inclusions in reservoirs;(4) experiment of synthetic hydrocarbonbearing inclusions is a good method for understanding the mechanism of oilwaterrocks interreaction in reservoirs.
文中报道在实际储层温压条件下(150 ℃,40 MPa,大约4 km深度)成功合成了碳酸盐岩烃类包裹体。通过对合成烃类包裹体的显微观察、荧光分析和傅里叶变换红外光谱分析,证实合成了烃类包裹体,且与真实储层中的包裹体具有相似特征,探讨了油水不混溶条件下的流体包裹体捕获机制。实验研究给出4点重要启示:(1)油水不混溶是造成烃类包裹体和水溶液包裹体分带的主要原因;(2)油气快速成藏过程可以被流体包裹体记录;(3)实际储层温压条件下,合成烃类包裹体实验研究有望为储层包裹体分析提供依据和标准;(4)人工合成烃类包裹体为研究含油气条件下储层水岩作用机理提供了一种有效手段。
-
Tectonic subsidence play dominant role in their geometric shapes, basin fillings, sequence evolution and sediment distribution in the Wushi Sag. Outline of the sequences are in shape of box-wedge or sheet-wedge and boundaries of sequences are varied from bilateral fault to monoclinal fault overlap, so that the sequences show distinct semigrabens which overlay in different ways. Seven sequences were formed in different stage of tectonic evolution. The sequence of SQ1 formed in initial rift stage and deposited alluvial sequence. Sequences SQ2-SQ4 developed in intense rift stage and sediment lacustrine sequence. Sequences SQ5-SQ7 formed in late period of rift before thermal subsidence and deposit mere and delta sediment. The place adjacent to the synsedimentary fault is the subsidence center and depocenter; meanwhile, controlling fracture migrates in horizontal made subsidence and sedimentary center of the sag changed.
构造沉降是控制层序几何形态,充填叠置方式、演化及沉积体系分布的最重要因素:凹陷由多个半地堑在不同层序发育时期以不同方式叠置联结而成;受断层控制,层序外部形态有箱状-楔形、楔形-席状披覆型,边界终止方式有双断终止型、单断终止超覆型;不同构造演化阶段层序内部充填的沉积体系各具特征,初始断陷阶段的SQ1沉积冲积层序,强烈断陷阶段的SQ2-SQ4充填湖相层序,晚期断陷阶段SQ5-SQ7内部充填浅湖和河流三角洲沉积;同沉积断层陡坡带沉降迅速、可容纳空间快速增长,是凹陷的沉积和沉降中心,断陷期主控断裂活动时间和空间的变化导致了凹陷沉积和沉降中心的迁移。
-
This project was established based on the first cooperative development of optical in situ real time detecting technique probing the atomic scale layer-by-layer epitaxy growth of oxide film. Over the last three years, we have given full play to the advantages and characteristics of both sides and have finished the assumptions and plans of this subject satisfactorily. 1. In Institute of Physics, we set up advanced oblique-incidence reflectivity difference equipment and wrote one data acquisition procedure that made the simultaneous detection of optical signal and RHEED signal into reality. 2. The first observation of sustained oscillations over hundreds of monolayers in both real and imaginary signals during the epitaxy growth of SrNb0.1Ti0.9O3 on SrTiO3 substrate in LMBE testifies that oblique-incidence is an excellent method to detect and monitor film epitaxy growth real time. 3. For the first time, we verify that oblique-incidence reflectivity difference method can be used to monitor the layer-by-layer growth mode during continuous growth through the correspondence between optical signals to atomic or molecular step edge density on the growth surface. 4. Phenomenological analysis shows that optical signals comprise three parts, the first is proportional to the average thickness of the film and depends on the bulk phase dielectric response; the second is proportional to the coverage of terraces and depends on the dielectric response of atoms or unit cells in the terrace; the third is proportional to the coverage of step edges and depends on the effective dielectric response of atoms or unit cells at step edges. This makes oblique-incident reflectivity difference technique a quantitative macroscopic method to monitor film growth.
中文摘要:本课题是在合作首次发展了氧化物薄膜原子尺度层状外延生长光学原位实时探测方法的基础上立项的,三年来,我们充分发挥双方的优势和特点,圆满完成了课题的设想和计划。1、在物理所建立了一套先进的光反射差法装置,编写了计算机系统的数据采集程序,实现了两路光学信号和RHEED数据的同步采集和显示。2、用激光分子束外延在SrTiO3基底上生长SrNb0.1Ti0.9O3薄膜,首次观测到连续外延几百个原胞层,周期振荡的光反射差实部和虚部信号,证明了光反射差法是一种能原位实时探测与监控薄膜层状外延生长的好方法。3、首次验证了通过对生长表面原子或分子台阶密度的响应,光反射差法可用于原位实时监测在连续生长条件下薄膜的层式生长模式。4、通过唯象理论的研究,证明光反射差信号由三项组成,第一项只与薄膜的平均厚度和宏观光学电介质常数有关;第二项与分子台阶面覆盖度和台阶面上分子层的光学电介质常数有关;第三项与台阶边缘的覆盖度成正比,并和在台阶边缘的分子的有效光学介电常数有关。
-
The geology research of carbonate reservoirs in Ordovician of Tahe oilfield showed that many large dissolved vugs and fractures were developed. The spread of the reservoir take on a very heterogeneous state. And the typical fractured-vuggy reservoirs was formed. According to the combination of the various spaces, the formation was divided into vuggy formation, fractured-vuggy formation and fractured formation. The research showed that development of the vug is relevant to the its position on the structure, the fractures, the water surface and the weathering surface. Multi-phase charge and recharge of the oil in the reservoirs resulted in the complexity of the fluid distribution. So the"Bottle Model"was brought forward to explain the movement of the water-oil contact. The special storage space and the complex fluid distribution lead to the unstability of the production and the complexity of the water cut. In order to explain the characteristic of the fracture-vug unit was brought forward and the basic principle and method of the partition of the fracture-vug unit was formed. The classification and evaluation of the units were performed according the reserve and energy. Based on the research of geology characteristic and the fluid flow in the reservoir the comprehensive numerical simulation plan of the fractured-vuggy reservoirs were established. Through the selection of the simulation unit, fluid flow type and parameter equivalent the triple media reservoir simulation model was established. Considering the practical application the model was resolved by the DKR decomposition conjugate grads method. Based on the fine reservoir description of Dsitrict IV of the Tahe oilfield the various space type were classified and combined together. The geology model of Unit S48 was constructed. Two typical single well model was established according to the geology and the dynamic phenomena. Finally the single well model and the Unit S48 were simulated by the triple media reservoir simulator. Via the local grid refinement and coarsening in the simulation good matchs were gained. Based on the results of the simulation the reserve distribution, percent of reserve produced in various space and the natural energy were analyzed. The fluid was storaged in the fractures and vugs mostly and more than 90% the produced oil came from the systems. The energy belonged to the active one. The results of simulation accorded with the fact and showed the validity and practicability the research and the simulator.
塔河油田奥陶系碳酸盐岩油藏的地质研究表明,其储层中发育着很多大型的溶蚀洞、缝,储层的平面展布呈现出极度的非均质性,形成了典型的缝洞型碳酸盐岩油藏,根据各种孔隙介质在储层中的组合,将储层分为了溶洞型、裂缝-溶洞型和裂缝型三类;研究表明溶洞储层的发育和构造位置、裂缝的发育、潜水面和风化面的位置等因素有关;多期充注的油气成藏模式导致了流体复杂的赋存状态,由此提出了所谓的"瓶子模型",解释生产过程中油水界面的变化;特殊的储集空间类型和流体分布特征导致油田在开发过程中表现出很大的不确定性和含水变化的复杂性,为了合理的解释油气田开发过程中的动态特征,提出了"缝洞单元"的概念,并制定了"缝洞单元"纵横向划分的基本原则和依据及划分方法,并对"缝洞单元"进行了分类和评价;基于地质特征和流体在其中流动规律的研究,提出了缝洞型碳酸盐岩油藏的数值模拟综合解决方案,通过模拟单元的选择、流动类型和参数的等效,建立了三重介质油藏三维三相数值模拟模型,采用不完全LU分解预处理共轭梯度法进行了求解;在塔河油田4区精细油藏描述的基础上,将各种类型的孔隙空间进行了归类组合,建立了S48单元的地质模型;通过对油井生产动态进行分析研究,建立了两类和油井地质、生产动态相对应的单井模型;最后应用三重介质油藏数值模拟软件对单井模型和S48单元进行了数值模拟,通过局部加密和粗化等技术模拟流体流动规律,取得了很好的拟合效果;结合数值模拟结果,分析了各种介质中的储量分布、储量产出的百分比以及地层的能量,认为塔河油田缝洞型油藏中流体绝大多数储集于缝洞系统之中,所产出流体90%以上也来自于缝洞系统,其底水能量属于较充足的类型;模拟结果和油田实际情况符合较好,说明了地质研究和油藏数值模拟研究的正确性。
-
Ni-P-mCMC/mCS bipolar membrane was prepared from carboxymethyl cellulose modified with phosphorylated agent as a cation exchange layer and chitosan modified with glutaraldehyde as an anion exchange layer. The electrolysis cell was constituted by Ni-P-mCMC/mCS BPM as a septum for electrogenerating furfural alcohol and furoic acid.
以磷酸化试剂改性羧甲基纤维素钠制备了阳膜层,以戊二醛改性壳聚糖制备了阴膜层溶胶,将阴膜层溶胶流延于阳膜层上,制备了P-mCMC/mCS双极膜,而后以化学镀方法在阳膜层表面镀镍,制备了Ni-P-mCMC/mCS双极膜,并应用于成对电合成糠醇、糠酸。
-
The pore distribution in the direction of coating thickness was self-existent and could not join to intercommunicating pore.The pore diameter was very tiny so that it could prevent hydrotropic solution entering into the pore.
机械镀锌的形层过程既没有热镀锌那样的高温冶金反应,也没有电镀锌那样的电沉积效应,镀层是常温常压下利用化学吸附沉积和机械碰撞使金属锌粉在工件表面镶嵌堆积而成[1],所以人们认为机械镀锌镀层的致密性要低于电镀和热镀锌镀层,但机械镀锌镀层又表现出良好的耐腐蚀性能。
-
Based on lots of achievements of predecessors, directed by reservoir sedimentology, high-resolution sequence stratigraphy and petroleum geology, taking full advantage of loggin, core and thin section data from different wells, this paper has taken detailed study on the Upper Paleozoic strata in Tabamiao area.
本论文在众多前人研究成果的基础上,以储层沉积学,及高分辨率层序地层学、石油地质学等理论为指导,充分利用测井、钻井岩芯、薄片鉴定等资料,针对塔巴庙地区上古生界沉积相及沉积微相类型与展布,高分辨率层序地层特征与层序—岩相古地理演化,成岩作用类型与序列,孔隙类型与特征,以及储层物性特征与分布规律等方面展开了系统深入研究,最后对有利区带进行了预测。
-
The phase structure of the ceramic-coating includes γ-Al2O3, AlPO4 and CoO. The forming process of the ceramic-coating includes iron movement, melting of surface layer, movement of electrolyte towards the melting-zone and the final nucleus-forming and sintering. The ceramic coating looks like islands and islets. The ceramic coating and the matrix are integrated metallurgically.
结果表明:该陶瓷膜层由γ-Al2O3, AlPO4和CoO等组成;通过对陶瓷膜层的表面形貌和显微结构观察及分析,发现陶瓷膜层形成过程是一个离子运动,表面层不断被击穿形成熔融区,处理体系中的电解质不断向熔融区运动、成核并迅速烧结的过程;陶瓷膜层呈现岛屿状;陶瓷膜层与基体之间为冶金结合。
- 推荐网络例句
-
As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.
每逢看到沃林顿那刚毅的脸,那乌黑、忧郁的眼睛,她便会相信,他一定作过不幸的爱情的受害者。
-
Maybe they'll disappear into a pothole.
也许他们将在壶穴里消失
-
But because of its youthful corporate culture—most people are hustled out of the door in their mid-40s—it had no one to send.
但是因为该公司年轻的企业文化——大多数员工在40来岁的时候都被请出公司——一时间没有好的人选。