成型

In most cases, metal bars with different shapes are used simultaneously. This research aims at the designing on new reinforcing bar cutter, presenting a mechanical design method for this new cutter, giving a computer controlling method of new cutter and showing a prototype to accelerate its common, use.

本文是围绕新型钢筋自动成型加工机的设计而展开的研究，给出新型钢筋自动成型加工机的机械设计方案，提出了实现自动成型加工机计算机控制的一种方法，并为此产品的最终推广提供了原型。

Study on the protection of the coatings in preventing oxidation and decarbonization of steel and iron materials during heat treatment;2. The present and prospect of semisolid steel and iron forming technology were discussed.

重点叙述了国内外各种钢在半固态成型过程中的组织演变机理及其力学性能，并介绍了半固态的坯料制备和成型工艺，对钢铁材料半固态成型技术的现状及发展趋势进行了分析讨论。

This paper introduces some fundamental principles of the Fused Deposition Modeling in Rapid Prototyping, and analyzes the factors influencing the prototype surface quality from two parts, which include the choice of prototyping direction and the prototyping parameter. Based on this, in response to these common quality problems in Fused Deposition Modeling prototyping, this paper puts forward some methods to improve quality.

介绍了快速成型技术中熔融沉积制造的基本原理，从成型方向的选择和成型参数两方面分析了影响原型表面质量的因素，并针对熔融沉积制造原型常见的表面质量问题，提出了改善质量的措施。

In the base of calibrating the elastic constant of cantilever and analysis adhesion force, the force information from force curve was obtained and the elastic modulus of single voxel was calculated.

考虑了成型点剩余部分形变对结果分析的影响，在标定微探针弹性系数和对粘附力进行分析的基础上，提取了力曲线中所包含的力学信息，推算出了成型点的弹性模量，得到了成型点的弹性模量低于宏观材料弹性模量的结论。

We used BET,FT-IR,XRD,TPR techniques to investigate the compression strength, the BET and the pore structure of catalysts by changing some factors such as the glutinousness and concentration of adhesive ,the ageing time and temperature and so on.

为解决催化剂侧压强度的不足，我们在实验室进行了超细镍基负载型催化剂实验室小试成型工艺条件研究，用硅溶胶及Ni~(2+)-硅溶胶两种不同的胶粘剂进行挤条成型，通过BET、FT-IR、XRD、TPR等技术考察了催化剂在成型过程中，胶粘剂的浓度、粘度，湿／干粉比，催化剂老化时间，以及焙烧温度等因素对催化剂的强度以及催化剂的比表面积和孔结构的影响。

Moldflow software was used for searching for optimal parameter of forming process of ABS gusset plate by simulating real condition.

通过模拟真实注射条件，应用Moldflow软件对 ABS扣板注射成型工艺参数进行了优化分析，得出影响注射成型顺利进行的主要因素，并模拟制定出扣板注射成型的最佳注塑压力、锁模力、模具温度、熔体温度、注塑时间、保压压力、保压时间和冷却时间。

Then, on the basis of above achieved constituent binary results, thermodynamic properties of 10 ternary liquid alioys (Cd-Bi-Pb, Cd-Pb-Sb, Cd-Pb-Sn, Mg-In-Cd, Zn-In- Cd, Cd-Bi-Sn, In-Bi-Pb, Sn-AgPb,Zn-In.Pb, Al-Cu-Zn), 3 quaternary ones (Cd-Bi-Pb-Sn, Zn-Sn-Cd-Bi, Zn-Sn-Cd-Pb) and 1 quinary. one (Zn-Sn-Pb-Cd-Bi) are predicted. For most of investigated multicomponent systems, the calculated activities are in good with the experimental ones, and in particular for multicompoment immiscible ones, the predicted results are satisfactory and exciting. At the same time, the comparison result between the three equations shows that Wilson equation and T-K-Wilson one are more stable than NRTL one, that maybe is because NRTL equation contains a third parameter, and so ,to some degree, Wilson model and T-K-Wilson model are superior to NRTL model. And also the comparison between local composition models and other models such as Pelton- Flengas?method, Krupkowski formalism, mass action concentration model and Hoch- Arpshofen model shows that local composition models are more convenient and credible.

在此基础之上应用局部组成型模型对10个三元液态合金（包括Cd-Bi-Pb、Cd-Pb-Sb、Cd-Pb-Sn、Mg-In-Cd、Zn-In-Cd、Cd-Bi-Sn、In-Bi-Pb、Sn-Ag-Pb、Zn-In-Pb、Al-Cu-Zn），3个四元液态合金（包括Cd-Bi-Pb-Sn、Zn-Sn-Cd-Bi、Zn-Sn-Cd-Pb）和1个五元液态合金（Zn-Sn-Pb-Cd-Bi）的活度进行了预测，预测效果良好，尤其对Zn-In-Pb系和Zn-Sn-Cd-Pb等多元液-液共存体系热力学性质的预测也取得了令人满意的结果；同时对三个方程的比较分析表明：Wilson方程和T-K-Wilson方程在多元系热力学性质的预测中表现稳定，而NRTL方程由于引入了物理意义不清楚的第三参数，使得其具有不确定性和不稳定性的特点，因此Wilson方程和T-K-Wilson方程较NRTL方程更为优越；此外对局部组成型模型与其它模型（如Pelton-Flengas方程、Krupkowski方程、作用浓度模型和Hoch-Arpshofen模型）的比较表明：局部组成型模型同样是优秀的，甚至在某些方面更为简便和可靠。

The technology pervading were inciting exciting cnnovating and sustained revdution of injection principia.Using GAM would have a impellent action on plastic fashioning vocation of active.

此工艺的普及正激励着设计和成型方面令人兴奋的创新和注射原理持续不断的变革，对于塑料制品注射成型行业积极采用气体辅助注射成型新技术有一定的推动作用。

In order to accurately determine the forming temperature and time of the sintered wick and to offer methods for the fixation and extraction of the mandrel as well as the infilling of copper powders, this paper analyzes the forming mechanism of copper powders in the wick and investigates the manufactu-ring process of the capillary structure of the sintered wick in the micro heat pipe.

文中分析了铜粉颗粒在吸液芯中的成型机理，探讨了烧结式微热管吸液芯毛细结构的制造工艺，解决了吸液芯成型温度与成型时间的确定，以及烧结时芯棒的固定、抽出与铜粉颗粒的填充等相关问题。

This paper analyzes the forming mechanism of copper powders in wicks, probes into the manufacturing process of capillary structures of sintered wick in micro heat pipe, and offers means for ascertaining forming temperature and forming time, fixating and extracting the mandrel as well as infilling copper powders.

本文分析了铜粉颗粒在吸液芯中的成型机理，探讨了烧结式微热管吸液芯毛细结构的制造工艺，主要解决了吸液芯成型温度与成型时间的确定，以及烧结时芯棒的固定、抽出与铜粉颗粒的填充等相关问题。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。