成型

The influence of the figuration and the thick of the blank were analyzed from two factors ,the length of blank heat up and the lubrication condition.

研究了桥壳成型过程的毛坯加热长度和润滑条件对成型和壁厚的影响。

Finally, we discuss the scheme that how to use three modules of this system to reconstruct the filter tip molding set of Jinan General Group.

最后，还针对济南将军集团滤嘴成型车间的滤嘴成型机组，讨论一下使用该系统的三个模块(模拟量模块、开关量模块、脉冲量模块)进行技术改造的方案。

Compared three ceramic with frit performance of body, the study found that

对比了三种陶瓷烧结体的性能，研究发现，纯的氧化锆粉体烧结所需温度较高，且烧结密度相对较小，粉体干压不易成型，烧结体易断裂，晶粒发生分裂，不适合制备成型材料。

Injection molding is to make glutinous fusibility form required plastic product with designed shape and size in closed moulds under needed pressure by means of plastic extrusion and plasticity.

注塑成型是利用塑料的可挤压性和可模塑性，使粘流状态熔体在一定压力的闭合模具中成型具有一定形状和尺寸的塑件制品。

The behavior of gel was studied and the components of the gelation system were made out on the base of experiment and the requirements of gel-tape-casting process.

通过对凝胶体特性的研究，根据实验规律及凝胶流延成型的工艺特点总结了应用于胶凝流延成型的凝胶体系设计准则。

Shaped primarily responsible for the processing of raw materials shaped to irregular shape processing rules into the geometric figure.

成型机主要是负责对原料的成型加工，将不规则的外形加工成规则的几何图形。

Delcam PLC has launched a new version of its PowerSHAPE hybrid modelling software that offers a complete solution for designers of complex shapes, ceramics included.

最近 ，DELCAM公司推出了其最新版本的模压成型计算机软件－Powershape，它是专为造型复杂的设计，当然也包括陶瓷产品的成型。

For mixture, increasing appropriate amount of SAK series in content range, molding temperature of WMA can be reduced by 10~20℃. If more reduction needs, the amount of asphalt should be improved.

对沥青混合料而言，在合适的掺量范围内，适量提高SAK添加剂的剂量，可将混合料的成型温度降低10~20℃，如需进一步降低成型温度，则需要提高混合料油石比。

The preliminary plan and actualized blue prints were presented,which was to construct an interact teaching,interpenetrative and flexible polymer science experiment course combined polymer chemistry,polymer physics and polymer process.Students learn from molecular design to synthesize polymer compounds and character properties of the materials,them process them to an utilized produce in this course.

设想将高分子化学、高分子物理和高分子成型加工三门实验课程有机地串联起来，组建成一门包括从高分子材料设计(用计算机软件进行分子设计、性能模拟)、聚合物合成、性能测试到加工成型，能环环相扣、互动式的、柔性化的高分子科学实验课程；提出了初步的实践方案。

The product is widely used in pultrusion ,hand lay-up and RTM processes

改产品广泛应用于吉拉成型工艺，手糊成型工艺和树脂传统模型塑料工艺等。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。