惯性

The R-2800 radials powered the S-56 quite well and were very responsive to the throttles, but due to the inertia of this massive helicopter, pilots had to fly with much anticipation.

的 R - 2800 radials动力的 S - 56不错的和非常积极回应，向节流，但由於惯性，这庞大的直升机，飞行员飞得多的预期。

3D effect is analyzed and the average velocity of wave propagating in the pile, which mainly influences inverse interpretation, is discussed. Finally, the theory results are verified by model experiment. It is shown that 3D results have the same phase with ID results. The pile radius, the duration of impulse, the ratio of hammer radius to pile radius and shear velocity of the soil around the pile have influences on 3D effect. The best position of receiver is 0.55R from the pile center. The average velocity of wave propagating in the pile reduces due to transversal inertia effect and 3D effect.

结果表明：三维曲线与一维结果在相位特征上一致；波场图直观地反映了波在桩中的传播规律；三维效应与桩径、激振脉冲宽度、相对激振半径及桩周土剪切波速有关；传感器放在0.55R处可以得到干扰较小的信号；三维效应和横向惯性效应的存在会使桩中的波速减小，土的性质对波速影响不大；反演精度与缺陷的性质、激振条件有关。

Intermediate heat cycle can be reduced because the tail blade turbine steam humidity and reduce steam consumption. improve plant efficiency and thermal cycling in the unit were popular, however, Reheat temperature control system with nonlinear their targets, inertia, the characteristics of delay, Power Plant to become more difficult to control the system-paper fuzzy control theory and fuzzy logic, reconsidered conventional PID control law on the basis of the study and intelligent fuzzy PID control, the 300MW units Reheat fuzzy control process using adaptive PID control, the introduction of load feedforward. design configuration, the final design complex adaptive feedforward cascade control system and MATLAB for simulation, simulation results show that the response speed, Robust control and accuracy, the system has considerable advantages Unit to improve the efficiency and reduce the operational workload.

中间再热循环技术因其可以降低汽轮机尾部叶片的蒸汽湿度和降低汽耗，提高电厂的热循环效率而在单元机组中被普遍采用，然而，再热气温控制系统因其对象具有非线性，大惯性，大迟延等特点，成为火电厂较难控制的系统之－，本文运用模糊控制理论和模糊逻辑推理，在重新认识常规PID控制规律的基础上探讨了PID与智能模糊控制相结合，在电厂300MW发电机组再热模糊控制过程中使用自适应PID控制，引入负荷前馈，设计组态，最终设计出自适应复合型前馈串级控制系统，并在MATLAB中进行仿真模拟，仿真结果表明，在响应速度，鲁棒性和控制精度等方面，此系统都具有相当大的优越性，有利于提高机组的效率和减轻运行人员的劳动负荷。

Based on discussion of attached plate and analysis of beam elements calculation results, a experience formula is deduced for the calculation of a beam element's inertial moment.

基于对梁元带板问题的讨论及对大量梁元的实际计算结果分析，推导出该梁元惯性矩计算的经验公式。

When plunger running, for the centrifugal inertial force brought by crankshaft and impact inertial force generated by repeated running of plunger piston, the high power vibration and noise appear.

柱塞泵在运转过程中，主要由于曲轴产生离心惯性力和柱塞来回运动产生惯性冲击力，会产生较大的振动和噪声。

The blades are modeled as pendulums with the aim of analyzing the inertia effects of the blade and the periodicity of the system.

为了分析叶片的惯性影响和系统的时变性，将叶片模化为单摆模型。

The key targets of inertia navigation system are high precision and reliability, light weight and miniaturization.

中文摘要：高精度、高可靠性、重量轻、小型化是惯性导航系统追求的主要目标。

The key targets of inertia navigation system are high precision and reliability,light weight and miniaturization.

高精度、高可靠性、重量轻、小型化是惯性导航系统追求的主要目标。

High-speed spindle system should have sufficient rigidity and high precision rotary; light weight, compact structure, small inertia; good thermal stability; vibration and noise; good cooling and lubrication system.

高速主轴系统应具有足够的刚度和高的回转精度；重量轻、结构紧凑，惯性小；良好的热稳定性；振动和噪声小；良好的冷却和润滑系统。

Owing to the light weight and high precision of the aluminum wheel hub, there will be less distortion and inertia resistance during high speed rotating.

由于铝合金轮毂重量轻(与同样规格的铝或钢轮毂相差约2kg)、制造精度高，所以在高速转动时变形小、惯性阻力也小。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了