性能

Firstly, the different effect of rectorite modification for the mechanical property of E-51 system were compared; the effect of organic clay for the viscosity and Gel-time of pure E-51 epoxy resin were checked separately; the influence of organic clay for hardening process was studied with FTIR technology; And, the infection of organic rectorite content in matrix for the mechanical property thermal-wet tolerance property aging resistance property and medium endure property for the both of two system were studied relatively. The effect of organization for the inter-layer distance of clay was denoted by XRD technology; To probe into the thermodynamics status about reaction, we investigated the heat discharging of reaction system in the help of DSC. The impact and crooking of solidifying system was observed with the SEM to investigate the decentralization of organic clay, and, at the base of this ,we discuss the mechanism of clay toughing-buildup polymer matrix.

分别考察了有机粘土对树脂体系粘度和凝胶特性的影响，利用红外光谱分析技术研究了有机粘土的加入对体系固化工艺的影响；分别考察了有机粘土含量对二体系的力学性能、耐湿热性能、耐老化性能以及耐介质性能等的影响；采用X-衍射实验表征复合材料中有机粘土层间距的变化；用视差扫描量热法考察了体系的放热情况，以探讨反应的有关热力学状况；通过扫描电子显微分析技术对浇注体的弯曲、冲击断口进行观察分析，以考察、表征有机粘土的分散情况，并在此基础上探讨了有机粘土改性环氧树脂的机理。

The influence of nanocrystalline particles and catalysts on the hydriding and dehydrogenating properties of magnesium-based hydrogen storage materials are summarized in this paper.

总结了纳米晶、催化剂改性等对镁基储氢材料吸放氢性能的影响，介绍了不同镁基储氢复合材料的吸放氢性能以及基于密度泛函理论的第一原理计算方法在镁基储氢材料吸放氢性能方面所做的一些基础理论研究，指出随着量子化学、凝聚态物理等学科以及计算机技术的发展，理论计算方法在研究镁基储氢材料吸放氢性能方面的作用将越来越重要。

As showed in Fig.1, the diagrammed stress of short time endurance test forAs showed in Fig.1, the diagrammed stress of short time endurance test for500 hours at 565℃on welded-joint of T91-F12 is 240MPa. Considering the℃on welded-joint of T91-F12 is 240MPa. Considering thedispersity of±20％, stress of check test for 500 hours is 192MPa. The result±20％, stress of check test for 500 hours is 192MPa. The resultof short time endurance test for 500 hours at 565of short time endurance test for 500 hours at 565℃on T91-X20CrMoV121℃on T91-X20CrMoV121welded-joints is showed in Tab.5. The result shows that the short timewelded-joints is showed in Tab.5. The result shows that the short timeendurance stress of weldedendurance stress of welded-joints with two procedures at 565℃for 500 hours-joints with two procedures at 565℃for 500 hoursboth above 192MPa, and meet the requirement.both above 192MPa, and meet the requirement.

依据图1，对T91－F12 焊接接头 565℃温度下的短时持久性能 500 小时考核试验依据图1，对T91－F12 焊接接头 565℃温度下的短时持久性能 500 小时考核试验的图示应力值应为 240MPa，按照持久强度试验数据的±20％的分散度，取 500的图示应力值应为 240MPa，按照持久强度试验数据的±20％的分散度，取 500小时考核试验应力值为 192MPa.T91－X20CrMoV121 焊接接头 565℃、500 小时小时考核试验应力值为 192MPa.T91－X20CrMoV121 焊接接头 565℃、500 小时短时持久考核试验试验结果见表5 ，试验结果表明，两种工艺条件下的焊接接头短时持久考核试验试验结果见表5 ，试验结果表明，两种工艺条件下的焊接接头565℃温度下的短时持久性能，500 小时的持久断裂应力均高于 192MPa，结果符565℃温度下的短时持久性能，500 小时的持久断裂应力均高于 192MPa，结果符合要求。

The effects of various antioxidants on the discoloring behavior and the mechanical properties of the PA6 specimens during the course of thermal-oxidative aging were systematically studied.

研究结果表明：使用胺类抗氧剂能明显地改善PA6的抗热氧老化变色性能，还能使其保持较高的热稳定性能和力学性能，并大大延长PA6的静态使用寿命；用酚类抗氧剂/亚磷酸酯抗氧剂组成（1：1）的稳定体系能对改善PA6的耐热氧老化性能产生协同效应。

This welding wire not only has the inherent properties of metal powder-cored wire, such as with better welding quality, without slag, highly efficiency and conveniently adjusting the alloying elements etc., but also has the advantage of low hardness in as-welded (less than HRC45), good machinability, high hardness in as-aged (more than HRC55) and better wear resistance with customary working procedure on making or repairing equipments such as rollers when reasonable designing the alloys content. The author adequately makes use of the high-tempering in the required stress relieving working procedure. During this working procedure, which causes the hardness of overlaying metal increased by the reason of austenite changes into tempered martensite and more chiefly what is the precipitation of a lot of carbide by secondary hardening simultaneously. This wire can solve the hard rolled problems of some solid wires with higher alloys while it can get over the conflict of existing overlaying materials what are always possesed high hardness with poor machinability or low hardness, good machinability with poor wear resistance. Further, it also can overcome the intenerating phenomena between welding beads and make the external hardness of overlaying metal uniform. Be sure it could be found important meaning in the overlaying of wear-resistant equipments, such as the precise roller.

该焊丝除了具有金属粉型药芯焊丝焊接质量好、无渣、高效率和合金成分可方便调节等固有的优点外，合理的设计粉芯中的合金成分，按通常工序制造与修复轧辊等设备，充分利用必需的消除应力工序的高温回火，堆焊层金属在奥氏体转变为回火马氏体的同时更主要是通过二次硬化析出了大量碳化物导致硬度增加，使得该焊丝还具有焊态硬度低(小于HRC45)、机加工性能好和时效态硬度高(大于HRC55)、耐磨性能好等优点，解决了某些高合金实芯焊丝轧制困难的问题，同时克服了现行堆焊材料硬度高、加工性能差或者硬度低、加工性能好、耐磨性差的矛盾，并能克服焊道之间的软化现象，使堆焊表面硬度较为均匀，对耐磨件，譬如精轧辊的堆焊具有重要意义。

First of all, the history of phase locked technology and the actuality of researches on it are introduced. Then, beginning with the fundamental principles of a phase-locked system, we build the mathematical model based on the architecture of the traditional analog PLL, and afterwards investigate some of its characters such as tracking, acquisition, noising, and stability. The system parameters are developed at the same time, and some universal conclusions on the theoretical analysis of PLL are reached.

论文首先对锁相技术的发展历史和研究现状做了简单介绍，然后从锁相系统的基本工作原理引入，以传统模拟锁相环的结构为基础，分析了锁相环的数学模型，并以此为出发点对锁相环的跟踪性能、捕获性能、噪声性能以及稳定性等各种性能进行了深入的分析，对环路的各项参数指标进行了详细的推导，得出了锁相环数理分析的普遍结论。

Through the morphological observation on silicon particles of Al-Si-Cu-Mg cast alloy, it is found, that during solution heat treatment the evolution of eutectic silicon morphology and their effect on mechanical property can be classified into three stages. In the initial stage, necking, stubbing and fragmentation of silicon particles results in an improvement in plasticity of the alloy. In the intermediate stage, the mechanical properties of the alloy attain peak values due to the spheroidization of silicon particles.

在固溶处理过程中，共晶硅相形貌发生了显著的变化，并对合金的性能产生了很大的影响；通过定量金相分析，共晶硅相形貌的演变及其对合金力学性能的影响可划分为三个阶段：固溶初期硅相的熔断和钝化使合金的塑性得到显著的提高；固溶中期以粒化为主，合金的力学性能达到了峰值；固溶后期硅相的粗化符合LSW粗化模型，硅相形貌呈现棱角小面特性，合金性能降低。

The effects of decabromodiphenyl,antimony trioxide and decabromodiphenyl(oxide/antimony) trioxide on flame retardancy and mechanical properties of low density polyethylene films for packaging were studied,and the flame retardancy and mechanical properties were estimated by a limiting oxygen index apparatus and an universal test machine.

以十溴二苯醚、三氧化二锑为阻燃剂，对包装用低密度聚乙烯薄膜制品的阻燃性能和力学性能进行了研究，并用氧指数测试仪和万能试验机评价其阻燃性能和力学性能。

The results show that: processing aids which mainly consist of unsaturated aromatic hydrocarbon and aliphatic hydrocarbon resin are able to improve the dispersion of the wood flour in PVC matrix, and amend the interfacial compatibilities between PVC matrix and wood flour, and enhance the mechanical and processing properties of PVC/ wood flour composites; Processing aids which mainly consist of calcium soap and saturated fatty acid amide mixture, as well as fatty alcohol and fatty acid ester mixture, are also able to improve the dispersion of the wood flour in PVC matrix and enhance the processing property of the composites, but when the use amount is big, they have adverse effects on mechanical properties of the composites.

结果表明，以不饱和芳香族碳氢化合物、脂肪烃树脂为主要组分的加工助剂，能够提高木粉在PVC 基体中的分散性，改善木粉与PVC 的相容性，从而明显提高PVC木塑材料的力学性能和加工性能；以钙皂和饱和脂肪酸酰胺混合物、脂肪醇和脂肪酸酯的混合物为主要组分的加工助剂，对木粉的分散性和复合材料的加工性能有一定的改善，但其用量较大时对复合材料的力学性能有不利影响。

The motive of this paper is to investigate the effect of processing parameters on the properties of silicon nitride and the coverage performance of insulator layer, and the effect of the film thickness of interface layer on the conduction current performance of thin film transistor.

本文旨在研究探索工艺参数对氮化硅薄膜的性能(如光禁带宽度、相对介电常数、折射率等)和钝化层氮化硅薄膜台阶覆盖性能的影响，以及栅界面层氮化硅薄膜厚度对薄膜晶体管导通电流性能的影响，制备性能优良的氮化硅薄膜。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。