径向的

On the basis of dual porosity theory,the well test interpretation model which considers the variation of krg versus the volume of liquid is also established and resolved by the implicit method numerically.

摘要通过分析凝析气藏的相图，建立了凝析液饱和度随压力降的变化规律，并回归得出了相应的公式；同时通过对气体压缩因子、黏度随压力、温度的变化，建立了这些参数和无因次压力的关系；在双重介质地层假设的基础上，建立了在试井过程中凝析气相对渗透率随凝析液饱和度变化的凝析气藏试井解释数学模型，采用隐式迭代的方法进行了求解并进行了参数敏感性分析；结果表明：凝析液的饱和度对凝析气藏试井的压力及压力导数曲线有着很大的影响，早期由于凝析液的析出，阻碍了气藏的流动，导致压力及压力导数曲线上升；在凝析液饱和度达到峰值之后，随着凝析液的挥发，凝析气的相对渗透率逐渐恢复，压力及压力导数曲线又回归到正常的径向流位置；由于裂缝和基岩之间的压力差，使得裂缝弹性储容比在测试过程中发生变化，进而影响了压力及压力导数；窜流系数和裂缝弹性储容比的变化决定了窜流段发生的早晚和程度；而基岩中气体黏度的变化使得窜流的发生稍微滞后。

The calculation results shows that ,(1) when the rotor rotates at the working speed, a local regurgitant whirlpool that is rightabout to the rotor"s rotating direction appears in the classifying region, which makes the separated granules come back to the outside of the classification district and influences the classification efficiency of the turbine classifier;(2) in the condition of a low rotating speed of turbo rotor, ultrafine particles can follow the gas phase by and large, but when the rotating speed increases, a phenomenon of velocity slippage between two phases appears evidently;(3) A operating parameter, air flow rate is so important that can directly influence the stability of flow field in classifying chamber, the bigger the air flowrate is , the steadier the flow field is;(4) Compared with straight blades, the new shape of blades with backward crooked elbow are helpful to improve the stability of flow field and form whole stream easily, also beneficial to advance the classification accuracy and classification efficiency;(5) The motion trace of particles are very complicated when the turbo rotor rotates at a high speed, the constant bounce of the particles appear between the blades and the coarse particles are even bounce back from the inlet, only the finer can pass through the classification area from the oulet;(6) Along with the increase of the rotor"s rotating speed, radiah axial and tangential velocity all begain to fluctuate repetitively like sine-wave, the smaller the particles are, the more violently they fluctuates.

数值模拟结果表明，(1)在涡轮达到工作转速时，在分级区域形成了一个与涡轮旋转方向相反的局部回流涡，它使得分离出来的细粒重又被带回分级轮外边缘，从而严重影响分级机的分级效率；(2)粉尘粒子在涡轮低速运动情况下，基本上能跟随气体运动，但随着转速加大，两相之间出现了明显的速度滑移现象；(3)分级机工作时的风量也是一个比较重要的操作参数，它可以直接影响到分级机内腔流场的稳定性，风量越大，流场越稳定；(4)同直叶片形状相比较，带后弯导板的叶片，有利于改善流场的稳定性，流场容易形成整体流，对提高分级效率和分级精度都非常有利；(5)粒子轨迹线在涡轮转速较高时十分复杂，有的出现了反复的弹跳现象，大颗粒不能通过分级区域而从进口返流了，只有细小的颗粒才从出口处流出；(6)涡轮转速加大时，粒子的径向、轴向和切向速率出现了明显的类似于正弦波的脉动现象，颗粒越小，脉动程度越为剧烈。

This paper studied the relationship between impulsive moment of radial tidal current and Alai phenomena, and concluded that: M acting on the earth's axis inspires Chandler wobble; the change of M depends on the interaction of the water, tidal force and the effects of the earth's rotation; under certain conditions, M changes dramatically during eclipse, which makes the amplitude of Chandler wobble change in the form of pulse.

本文研究了径向潮流冲量矩M与阿莱现象的关系，得出的结论是：M作用于地轴激发了Chandler摆动；M的变化取决于海水、引潮力和地球自转效应的相互作用；日食或月食期间，在一定的条件下，M变化的非常剧烈，引起Chandler摆动振幅脉冲式的变化，进而引起地球纬度的变化，最终导致地球表面重力加速度的变化；这种变化可以通过傅科摆摆动平面角速度的变化或重力计的示数变化反映出来。

Through the analysis of different cross section flow field in cylinder of two-valve and four-valve diesel engine, the following conclusion can be obtained: The formation of intake swirl of two-valve diesel engine mainly is effected by an intense air flow ring zone near the radius from valve axis to cylinder axis, as the flow progresses down through the cylinder, the ring zone air flow expends to both side and finally forms an unified rigid rotating swirl motion.

2号缸盖的螺旋进气道产生的绕自身气门轴线的动量矩比1号缸盖的大，且切向气道的径向速度在前峰面上的数值比1号缸盖的速度数值大很多，因此，两进气道组合后的动量矩损失也大，所以虽然2号缸盖的两个进气道单独的涡流比都高于1号缸盖的两个进气道，但组合后的合成涡流比却是基本相同的。

Analysis is made on block effect to cutters of PDC bit with 3 factors: different top shape,cutter-distributing and wearing degree.By the interaction(radial range and altitude difference of each cutter) of three adjacent cutters,the cutter block is further analyzed with these factors,but wearing degree is simplified to be considered as the cutters vertical to the assembling plane.

中文摘要：对PDC钻头冠部形状及不同的布齿密度和切削齿在不同的磨损状态下对PDC钻头切削齿受力的影响进行了分析；用相邻的3个切削齿之间的关系（不同的切削齿与切削齿之间的径向距离和切削齿之间的高度差）来分析PDC钻头冠部形状和切削齿布齿密度对切削齿受力的影响，以及将切削齿的磨损状态简化成与切削齿在钻头上装配方向垂直的平面来分析切削齿磨损状态对切削齿受力的影响。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。