径向的

The results show that although the effect of Poisson is one of the factors that led to the cracking of soleplate, but not a major factor. Among the causes of the longitudinal cracks in bottom plate, not only the radical force are considered by traditional theory, but also the warping effect of the box and the local trabecular are serious and can not be ignored.

分析结果表明：泊松效应尽管是导致底板开裂因素之一，但不是主要因素；而底板纵向裂缝的产生除了传统理论所认为的底板连续索所产生的径向力效应外，底板连续索导致的箱梁翘曲效应与局部小梁效应也是重要的、不可忽略的因素。

After analyzing the radial and axial temperature distribution of CMT, the primary result has been concluded: With the same initial pressure of the CMT drainage with sparger, the higher the average temperature of CMT fluid is, the shorter the disturbing time, and the large the temperature difference of the top and bottom layer fluid.

对实验测得的CMT径向和轴向温度分布进行了分析，发现在PRZ初始压力相同时CMT无遮流板排水，其扰动时间随CMT液体平均温度的升高而减少，上下层液面温差随之变大；加遮流板后对凝结和温度平衡时间起主要影响的因素有两个，即遮流板以上液体的温度与PRZ的初始压力大小。

The device comprises: a conveyer belt; a let-off roller (16) on which the conveyer belt runs and from which the rubber tape is let off; a traverser (21) to move the let-off roller (16) in an X-axis direction parallel to the rotational axis of the object; a radial shifter to move the let-off roller in a Y-axis direction perpendicular to the X-axis direction; a tilter (23) to turn the rotational axis of the let-off roller (16) around a reference axis which is parallel to a Z-axis direction perpendicular to the X-axis direction and Y-axis direction.

所述装置包括：输送带；送出辊，所述输送带在送出辊上行进并且所述橡胶带从送出辊送出；移动台，其沿平行于物体的旋转轴线的X轴方向移动送出辊；径向移位装置，其沿垂直于X轴方向的Y轴方向移动送出辊；倾转装置，用于绕平行于Z轴方向的基准轴线转动送出辊的旋转轴线，所述Z轴方向垂直于X轴方向和Y轴方向。

Experiment result indicates that the RFHP has greater thermal diffusivity, and can reduce junction-to-case thermal resistance of the module. When power density is 176W/cm^2, the temperature difference on the condensation section is within 3℃. The longer time period for the chip to reach the same temperature during RFHP module start-up can avoid power uprush and raise the ability of resisting thermal impact.

结果表明：与铜基板相比，径向平板热管具有更高的热扩散能力，可降低模块的结壳热阻；热管冷凝面具有良好的等温性，当芯片功率密度为176W/平方公分时，热管冷凝面的温差在3℃以内；热管模块启动过程中芯片达到相同温度需要的时间长，有利于克服功率"飙升"和提高功率器件抗热冲击的性能。

Flow visualization and laser velometer measuring results show that the radialdistribution of turbulent intensity and turbulence stresses grow with the increase of voidfraction until large vortex formed near the pipe wall,and the formation of Taylor bubbleor the coalescence of bubble cluster should be restrained by intense turbulence.

流动显示和激光测速计的测量表明，湍流强度和湍流应力的径向分布均随空隙率的增长而迅速增长，直至在近壁形成大尺度涡结构，使Taylor泡的形成或气泡群的聚并被强湍流的作用抑制。

The azimuthally linear advection may results in that the meso-scale vortex of initially circular shape becomes the elongated and spiral vorticity bands; the radial linear advection may transfer the vorticity of the outer region towards the center of the typhoon.

沿e方向的线性平流可使初始圆形的中尺度涡旋演变为狭长的螺旋状的涡量带；沿径向线性平流的引进可使外区涡量向台风中心方向传播。

The results along the way of tunnel doors radial direction, received through microcosmic analyses and researches about macrosopical model, can be divinable guide when designers chose types of tunnel and plan support structures.

本篇论文基于宏观模型的细观分析研究，得到的沿洞口径向路径的分析结果，更能对设计人员在洞形选择、后期支护结构的设计等方面提出可预见性的指导。

On base of analysis to simulation result, it was point out the main cause making dissimilar metal"s bonding so difficult was metal"s inharmonic plastic deformation. The distribution and changement of stress and strain on interface and in workpieces were analyzed.Making use of experiment and simulation result, main factors that influence welding property of cold pressure welding were discussed.

通过对模拟结果的分析，说明了异种金属冷压焊较同种金属冷压焊困难的原因主要是界面处两种材料的径向和轴向的不协调塑性变形；直观地显示了冷压焊过程中工件内部及界面处的应力应变分布及变化情况。

The results of simulation experiments for single channel data or arbitrary channel of multi-channel data show the clearer event, the better wave shape and the higher SNR compared with the conventional convolution filter and common SVR based on RBF. So it is possible that SVR based on Ricker wavelet kernel function is applied to suppressing noise in seismic prospecting data.

对单道记录或多道记录中任选道的仿真实验表明，与传统的基于径向基核函数的支持向量回归及褶积滤波方法相比，使用本方法去噪后的同相轴更为清晰，波形恢复得更好，信噪比也较高，因此有可能将其应用于地震勘探记录的去噪处理中。

For low permeability oilfields, radial flow straight-line portion should not appear in producer measuring data during shut-in build up tests. A practical method to interpret formation parameters based on well testing data at early fillup period has been established With the application of this kind of method, ideal interpretation results can be obtained when the measure pressure data lie above and under semilog straight-line portion, and the formation parameters can be interpreted more reliably.

对于低渗透油田，在通常的关井压力恢复测试中，油井测压资料不能出现径向流直线段，针对这种情况建立了一种用早期续流段试井资料解释地层参数的实用方法，通过计算续流量利用褶积分析方法解释早期试井资料，可对实测压力数据点落在半对数直线段上方和下方的两种情况都收到较理想的解释效果，能解释出比较可靠的地层参数。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。