影响

So supported by well core experimentation, the *** analyzed the logging response feature and mechanism of thin bed, and point out that many factors can affect the logging response of the reservoir, the main factor which mostly influence the logging response is the thickness of thin layer, and the content of carbonite have a great influence on the response of 3-porosity logging.we make use of core experimentation, combined with logging material, firstly the *** do the lithology correction and thinckness correction for resistivity curves, and based on the content of mud that derived from the core experimentation, the *** present the thickness correction model of gamma-ray logging and self-potential logging, and choose the appropriate ways to compute the carbonate content and using the value of mixed frame in order to correct the influence from the carbonite, based on this, the *** gives a effective methods to correct the thickness influence for 3-porosity logging.

本文首先以岩心实验结果为依据，对研究区薄层的测井响应特征和机理进行了分析，指出多种地质因素影响着储层的测井响应特征，而层厚是影响测井响应最主要的因素，且碳酸岩含量对三孔隙度测井的影响很大。利用岩心实验分析资料，结合测井资料，首先对电阻率测井曲线进行了岩性的校正和层厚校正；利用岩心分析泥质含量，研究了自然伽马和自然电位的层厚校正方法，并建立了层厚校正模型；在有效计算储层碳酸岩含量和混合骨架参数值的基础上，研究了针对碳酸岩含量对测井曲线的影响进行校正的方法，进而提出了一套对三孔隙度测井曲线的薄层层厚影响的校正模型。

But ECT technology has the following characteristics: 1 the measured capacitance and its change induced by the measured material concentration variation are very small, but the stray capacitances of co-axial screening cable and CMOS switches are relative very large, so the capacitance detecting is easily affected by the stray capacitances, 2 the electric fields in the sensors detecting region is affected by the permittivity distribution, non-uniformity of the space responsive sensitivity is very high, and the image reconstruction is undetermined.

但由于ECT技术中，首先所检测的微电容量及其因物流相含率的变化所引起的变化量很小，而由相关的连接同轴屏蔽电缆与切换CMOS开关所引入的杂散电容远远大于测量电容，微电容的测量容易受杂散电容等的影响；其次，多电极电容传感器测量区内的电场受介质分布的影响，且测量区内的空间响应灵敏度极不均衡，其影响图像重建的不确定性；其三，ECT中的图像重建，由于其是一个欠定问题的求解，在迭代求解方法中，迭代的初值影响迭代过程收敛到近似解的速度；其四，对于气/固两相流应用而言，由于ECT系统在线标定的难以实现，管壁磨损等因素的影响制约该技术应用于生产工艺中气/固两相流的长期连续检测。

Tested results and analysis show: seed condition has a significant effect on bulk density, a comparatively significant effect on drag coefficient, and little effect on particle density and restitution coefficient of rice seed; moisture content significantly affects bulk density, particle density and drag coefficient of coated rice seed; variety of seed has little effect on the properties of coated rice seed.

试验结果和分析表明：稻种状态对容积密度影响显著，对漂浮系数影响比较显著，对籽粒密度和恢复系数影响较小；含水率对包衣稻种的容积密度、业粒密度和漂浮系数影响显著；品种对包衣稻种的物理特性影响较小。

From this research, we realized the difference between ROT and BOT, for example, ROT would be easier to execute the EIA contents and conclusions. Its confidentialness in monitoring result was also higher than BOT cases. For the EIA approval kinetics, 26 approval specifications and the key items for 3 levels approval system were also offered. The policy, EIA, EIA assessment system, EIA contents development, approval system, key points for examining, following, monitoring and the results for executing effects for the surrounding facilities were researched and analyzed to offer the suggestions for practical application between Developer and Administration for the reference of executing and research.

并藉由本研究探讨，了解公有民营与BOT垃圾焚化厂环境影响评估差异性，如：公有民营对环评内容及审查结论较易执行，且民众对其接受度较高，环境监测结果公信力也高於BOT垃圾焚化厂等，另针对垃圾焚化厂环境影响评估审议机制，研拟出26项审议规范及区分三级之审查重点项目，并提出开发单位、主管机关於政府政策环境影响评估、环境影响评估制度、环境影响评估内容撰写、审议制度、审查重点、追踪与监督及执行成效与民众对邻避设施的观感等加以探讨分析之结论与实务操作运用的建议，作为未来执行及研究之参考

The effect of tribology factors on bearing vibration is studied experimentally. AR model and WPT are used to processing the normal arid abnormal signals. The results are as follows:1. The vibration of ball bearings is caused by the tribology action of contact pairs of ball and ring races and has the essential of tribo-dynamics. Any factors affecting the tribology characteristics of contact pairs will affect vibration and noise of bearings consequently.2. Vibration characteristics of bearing keep almostly unchanged with the increasing of axial load expecting the increasing of nature frequencies. When radial load increasing with axial load unchanged, nature frequencies keep unchanged but some new vibration peaks appears in the spectrum.3. Vibration amplitudes are damped and nature frequency are enhanced with sufficient lubrication. Vibration and noise of bearings increase obviously and roar can happen and the contact surfaces scratch slightly under insufficient and unclean lubrication state. Bearing will be disabled in a few minutes without any lubrication.4. Bearing vibration is unstable under low speed. With the speed increasing, the vibration become stable and natural frequencies increase slightly but the amplitudes increase apparently.5. Bearing vibration can be excited only by some harmonics ofwaviness without lubrication and by all harmonics with lubrication based on the theoretical analysis.6. The nature frequencies of ball bearings decrease with the increasing sizes. When international clearance increasing, nature frequencies decrease in radial and increase in axial and angular and the amplitudes increase in radial and decrease in axial and angular. When the number of balls increasing, nature frequencies increase and amplitudes decrease. When the pitch diameter increasing, axial nature frequency increase and others nearly keep no change. When outer race groove curvature radius increasing, nature frequencies increase in radial and decrease in axial and angular and amplitudes keep no change in radial and increase in axial and angular. When inner race groove curvature radius increasing, nature frequencies decrease and amplitudes increase.7. The distortion in amplitude and frequency components of bearing vibration signals picked up by the present probe measurement method is founded and right conclusions cannot be achieved by the signals. When accelerometer is rigidly screwed with steel stud onto a flat outer surface of a ball bearing, vibration signal can be got without distortion and the reliability of research on bearing vibration is assured.8. AR model is suitable for large samples of bearing vibration signals, square root of length of samples can be used as the upper limitation of order determination and the FPE order selection criterion is effective. Many advantages of AR spectrum are founded over the classical based on FFT.9. Time-Frequency analysis is necessary for abnormal noise of ball bearings. WPT overcomes the principle shortcomings of STFT and proved to be a best tool to process the abnormal signals.

理论分析和试验研究表明： 1球轴承振动是钢球—滚道接触副中的各种摩擦学作用引起的，具有摩擦动力学的本质，任何对接触副的摩擦学特性有影响的因素都将对球轴承的振动和噪声特性产生影响； 2中心轴向载荷作用下，载荷增大使球轴承的固有振动频率升高，载荷越大同样的载荷增幅引起的频率升幅减小，足够大的中心轴向载荷作用下载荷的变化对球轴承振动的频率特性不会产生明显的影响； 3轴向和径向联合载荷作用下，径向载荷不大时球轴承振动的固有频率基本不变，但是可能引起变刚度激励的非线性振动，出现新的频峰，过大的径向载荷将使部分钢球脱离接触，使球轴承的振动和噪声呈现不稳定状态； 4润滑对球轴承的振动和噪声特性有重要的影响，良好的润滑对振动有明显的抑制作用，润滑不充分时，振动和噪声的水平会有明显增高，一定条件下还会激发接触副中的谐振，发出啸声，造成接触表面的伤害，无润滑干接触时，短时的运转就会损伤接触副表面，使振动和噪声迅速增大，并随时可能引发严重的磨损和卡滞失效；接触副润滑良好时，油膜的"刚化效应"使球轴承振动的固有频率有所提高，润滑剂中含有弥散性污浊时，振动的幅度总体升高，但弥散性污浊不会改变球轴承振动的频率特性；浙江大学博士学位论文：球轴承振动的研究 5低速时，球轴承振动的基本特征呈现不稳定状态，随着转速的提高，球轴承振动的频率特性趋于稳定，固有频率频峰升高； 6理论分析表明，干接触时钢球和滚道表面波纹度的某些谐波分量能激励球轴承的振动，振动的幅值与谐波幅值成正比，实际球轴承中钢球的分布不可能完全均匀，波纹度的激励作用会随时发生；润滑接触的分析表明，波纹度的任意谐波分量均能激励球轴承的振动； 7球轴承的几何和结构参数分析表明，球轴承尺寸越大，径向、轴向和角振动的固有频率越低；钢球中心圆直径增大，球轴承的径向和轴向振动的固有频率基本不变，角振动的固有频率有所上升，振动的幅频特性基本不变；径向游隙加大使球轴承的径向振动固有频率降低，轴向和角振动的固有频率有所升高，径向振动幅频特性的幅值升高，而轴向和角向降低；钢球的数量增多使球轴承振动的固有频率上升，幅频特性的幅值下降，径向振动的幅值下降最为明显；外圈沟曲率半径系数增大使球轴承径向振动的固有频率升高，轴向和角振动的固有频率降低，径向幅频特性基本不变，轴向和角向幅频特性幅值升高；内圈沟曲率半径系数增大使径向、轴向和角振动固有频率均下降，振动幅频特性的幅值均有升高； 8试验对比表明，传感器采用探针式安装时，由于探针接触副接触特性的影响，钡(量得到的球轴承振动信号有失真，采用专门设计和制作的试验球轴承，以固定式安装加速度计，首次测量得到了球轴承振动的真实信号，通过对振动信号的分析，验证了球轴承振动的理论模型； 9)基于时间序列分析的AR模型适用于大样本球轴承振动信号的分析，以样本长度的均方根值作定阶上界，FPE做判阶准则，给出的AR谱光滑，频率分辨率高，是球轴承振动分析的简便而可靠的手段； 10以时频域分析的小波包变换分析球轴承异音信号能够比较好地定位和聚焦异音发生的时间，时间间隔，频率范围，同样是球轴承振动分析的可靠的手段，可用作球轴承故障诊断技术。

The total influence is the sum of the direct influence and the indirect influence. By comparing the total influence of the economic-social factors and the bearing-controlled factors, this paper makes out the primary effect factor of the fertility level.

直接影响与间接影响之和即为总影响，通过比较经济社会因素和生育控制因素对生育水平的总影响，解析出1990年代中国生育水平的主要影响因素。

Analyzing and simulating of the deformation law of the ceramic downspout product after overcoming the shortage of powder material models in the software of MSC. MARC. It shows out the important effects of various factors and the shape of mandril during the process. And it is obvious that the shape of the top mandril has more effects on the process than the bottom.(3) Showing out the important effects of model figure on the flowing of powder and the forming of low-density fields from the analysis. After changing the top of the mandril into spherical shape, an improving model is putting out so that the distribution of stress and strain turns to be even and proper and that the flow rule of powder grains is better.(4) Calculating of the dimensional precision and the cutting ratio of the product and analyzing of the effects of such factors as rubber aging, loading process, mandril, friction etc. on the cutting ratio.

MARC存在的粉末材料模型方面的设计缺陷后，对连铸水口粉末成形件的变形规律及影响因素作用进行了模拟分析，指出芯棒形状对成形件的变形有较大影响，并且芯棒顶部形状与芯棒底部形状相比，对粉末变形有更大影响；(3)分析了成形件出现低密度区域的原因，指出模具形状对粉末流动以及粉末成形件低密度区域的形成有重要作用，提出了密度分布优化改进模型：改进模具顶部形状，并将芯棒顶部设计成球面后，粉末成形件顶部区域的应力、应变分布更加均匀、合理，粉体颗粒流动情况明显改善，低密度区域明显缩小；(4)计算了成形件的尺寸精度及切削率，并指出除模具形状的影响外，充填密度、橡胶模具老化、加载工艺等其他因素对总体切削率也有相当的影响。

This paper also analyzes the ash wear mechanism,and then does the effects of low temperature economizer wear five factors: the first is the smoke corridor caused by wear mechanism,the second is the impact on the wall material,and the third is that of flying ash concentratio.

分析了飞灰磨损的机理，然后分析了影响低温省煤器磨损的5种因素，一是烟气走廊引起磨损的机理；二是管壁材料的影响；三是飞灰浓度的影响；四是过量空气系数的影响；五是烟气成分的变化对磨损的影响。

The first part discusses about the effects of the five factors:temperature,relative air moisture,rate of frass sifting,density of larvae,fodder water percentage to growth speed and survival rate of older mealworm (Tenebrio molitor L.) larvae through rotational composite design of quadratic regression. Two models were established to describe the effects of the five factors. The models showed that percentage of fodder water is the major factor that has effect on the growing speed of T. molitor larvae,and fodder water is the major factor on death rate. The models also show that temperature on growth speed,temperature and fodder have important effects on death rate,and the significant test showed they have significant difference on 1% or 5% level. From the two models,by frequency analysis,we can get the optimizing rearing condition,in which the mealworm larvae overweight 10% per day,temperature is 25-26 ,frass sifting rate is once 2-4 days,density of larvae is 0.61-0.79 g/cm2,fodder water is 33.27%-39.71%. And the rearing condition,in which total death rate of T.

第一部分：采用五因素二次正交旋转组合设计，以黄粉虫幼虫饲养过程中饲养温度(X_1)相对湿度(X_2)、虫粪筛除频率(X_3)、饲养密度(X_4)以及饲料含水量(X_5)五因素为参试因素，考查它们对黄粉虫高龄幼虫的生长及存活的影响，建立了以黄粉虫幼虫增重率及死亡率为目标函数的回归模型，并进行了简化： Y_增=127.5079+18.6559x_5+2.7894x_3x_4-2.3854x_3x_5-3.0594x_1~2+1.8241x_3~2-3.8559x_5~2 Y_死=1.7459+0.4108x_1+0.0975x_2+0.9025x_4+0.3442x_5+0.0834x_1~2+0.3060x_4~2-0.2623x_5~2 分析结果表明：影响黄粉虫幼虫生长后期增重及死亡的主要因素分别为饲料含水量和饲养密度；饲料含水量和温度对黄粉虫增重有着重要的影响，饲养密度、温度、饲料含水量对黄粉虫的死亡有着重要的影响，其影响均达1％或5％显著水平；黄粉虫幼虫后期日增重率大于10％的饲养条件为：温度26～27℃、筛粪频率2～4天／次、饲养密度0.61～0.79g／cm~2、饲料含水量33.27～39.71％。

This paper analyze and study the influence of the superimposition in depth based on the previous achievements and combined with the theoretical qualitative analysis and project instances. The main contents as follow:Chapter 1: Indicate the significance and objective of this paper, review the previous achievements of the transient process and superimposition, and then present the study purpose of this paper.Chapter 2: combined with the physic knowledge of the fluctuation and the superimposition, Indicate the physical essences and the influence of the superimposition phenomena that exist in the diversion pipe system, and take one hydraulic turbine owning only one diversion tunnel and two hydraulic turbines sharing one tailrace conduit for instance to study out the numerical calculation superimpose operations.Chapter 3: From the calculation theory of the parameter of the guaranty calculation of regulation of the hydro-turbine, qualitative analyze the influence of the superimposition on them and the superpose time, combined with some project instances, get the numerical value of the influence of the superimposition and the superpose time.Chapter 4: Based on the previous achievements of the calculation and theoretical analysis of the surge-chamber ground swell, analyze the influence of the superimposition on it and the superpose time.

本文在前人研究成果的基础上，结合理论定性分析及工程实例，对波动叠加带来的影响进行深入分析研究，其主要内容如下：第1章，指出本文研究的意义和目的，回顾前人对水电站过渡过程及波动叠加方面的有关研究成果，在此基础上提出本文的研究内容；第2章，结合物理学中有关振动与波动叠加方面的有关知识，阐述水电站引水发电系统中存在的波动现象的实质及其影响，并以两机一洞和一机一洞具有上游调压室或下游调压室的水电站拟定其数值计算叠加工况；第3章，从机组调保参数的理论出发，定性的分析波动叠加对机组调保参数的不利影响及叠加时间，结合几个工程实例，得到波动叠加带来的影响大小及叠加时间；第4章，在前人对调压室涌浪进行计算和理论分析的基础上，分析波动叠加对调压室涌浪的影响及其叠加时间。

Singer Leona Lewis and former Led Zeppelin guitarist Jimmy Page emerged as the bus transformed into a grass-covered carnival float, and the pair combined for a rendition of "Whole Lotta Love".

歌手leona刘易斯和前率领的飞艇的吉他手吉米页出现巴士转化为基层所涵盖的嘉年华花车，和一双合并为一移交&整个lotta爱&。

This is Kate, and that's Erin.

这是凯特，那个是爱朗。