形槽的

The columella was nonsurgically lengthened from 1.13mm to 3.78mm (P.05). CONCLUSION: In order to obtain satisfactory lip-nose configuration for BCLP, presurgical NAM is useful in cleft lip and palate team approach.

双侧完全性唇腭裂患儿为了获得较为理想的鼻唇形态及牙槽骨的规则弧形排列，术前鼻－牙槽骨塑形是值得采用的序列治疗方法。

With understanding the numerical control milling machine in cam processing utilization, thus people can complete analysis of the discoidal cam numerical control mill technological capability , the programming and the analysis of grooved cam numerical control mill technological capability, the compilation of numerical control processing technological document.

了解数控铣床在凸轮加工中的运用从而完成盘形凸轮数控铣工艺性分析及程序编制和槽形凸轮数控铣工艺性分析及编写数控加工工艺文件。

Outside the clouds existed plates that were 57 cm and 100 cm from ignition point respectively.

气云外布置了平板形障碍物，平板距球心的距离分别为 5 7cm和 1 0 0 cm，平板的布置分为单板、双板垂直、双板平行、3板槽形和 4板口形放置 5种方式。

As shown by the results of the qualitative and quantitative micropaleontological analyses, the basic factor controlling the distribution of the foraminiferal and ostracod assemblages is water depth and offshore distance, although water temperature, currents and salinity have strong influence on their distribution.

东海沉积中有孔虫、介形虫定量研究的结果表明：河口、陆架内部、中部、外部、陆坡与海槽，分別具有不同的有孔虫、介形虫组合，它们受水深，水温与盐度等因素控制。

The optimal curve for pressure vs. time of superplastic bulging of such parts as long trapezoid groove and truncated cone etc. is calculated based on superplastic flow equation σe=kεem and their superplastic deformation pattern.

根据超塑性流动方程和长梯形槽、圆台筒等的起塑性变形模式，计算长梯形槽、圆台筒等在合适的恒应变率条件下胀形压力随时间的变化关系。

Seeds obovoid or obovoid-elliptic, base rostrate, abaxially 1-furrowed with a rounded or suborbicular or elliptic chalazal knot, adaxially 2-furrowed; endosperm M-shaped in cross-section.

种子倒卵球形或倒卵球形的椭圆形，基部具喙，背面的1棱槽具一圆形或近圆形的或椭圆形种脐，正面2棱槽；横截面的胚乳M形。

In possession of 20-year,s special productionand managerial experience,linking with the most advanced manufacturing engineering both at home and aboard,in the tenet of "uality First,Credit Highest"striving for innovation,and taking advantage of equipments and materials with high specification,high quality inJupan and Taiwan,etc.the orporation provide you high strength stainless steelmachine bolt,self tapping screw,trigonodont crew,setscrews of M2-M12 single-line slot,cross slot,inside and outside angle,pan head,conmbined screw,stainless steelspacer and special nut,such as stainlesssquare nut,hexagon nut,weld nut,welding yandage,folan screw nut,with annual output coming out in front of fellow industry.

公司拥有20年的专业生产及管理经验，融汇国内外最先进的制造工艺，力求创新，本着&质量第一，信誉至上&的宗旨，应用日本、台湾等高标准、高质量的设备及材料，为客户提供高强度M2～M12一字槽、十字槽、内外六角、盘头、沉头、尖头、平头等形状的不锈钢机械螺丝、自攻螺丝、三角牙螺丝、紧定螺丝；铝钉；全不锈钢铆钉、尾孔钉、子母钉；不锈钢垫片及不锈钢方母、六角螺母、焊接螺母、焊码、佛兰螺母等异形螺母，年产量名列同行业前茅。

If the bevel gear used in the processing module mid-point of the standard spur gear tooth milling cutter with big-deep into the alveolar knife milling, then the big-toothed on the "fat", little-endian tooth on the "thin."

如果在加工时采用伞齿轮中点模数的标准正齿轮铣刀以大端齿深将齿槽一刀铣成，那么大端齿形就&肥&，小端齿形就&瘦&。

The mechanical effects produced by the V-shaned notch which is under both the dynamic pressure of blast, wave and the quasi-stationary pressure of blast gas are studied, in detal .

本文详细研究了切槽爆破中V形切槽在爆炸冲击波的动态压力和爆生气体的准静态压力作用下产生的力学效应。

In this way, the formation of a groove it ABCDEA "i" shape of the seal space (such as single-head screw, the axial groove to Shun Rao screw plate to the mouth through the smoke emission and can not form a seal).

那样，凹槽ABCDEA也便组败一个&i&形的密封空间(如采取双尾螺纹，则凹槽将逆轴向盘饶螺杆，将吸排口贯通，无奈构成稀封)。

And Pharaoh spoke to Joseph, saying, Your father and your brothers have come to you.

47：5 法老对约瑟说，你父亲和你弟兄们到你这里来了。

Additionally, the approximate flattening of surface strip using lines linking midpoints on perpendicular lines between geodesic curves and the unconditional extreme value method are discussed.

提出了用测地线方程、曲面上两点间短程线来计算膜结构曲面测地线的方法，同时，采用测地线间垂线的中点连线和用无约束极值法进行空间条状曲面近似展开的分析。