弹簧阀

Rotate the handle to a certain position, so that the distance between the nozzle baffle within the scope of work, pressure reducing valve to enter the work state of the pressure chamber 5 with the nozzle and the decrease of distance between baffle increases, so promoting the spool, Open the intake valve port 9, that is, air flow to exit the same time, through the pore back to the previous chamber 4, with the pressure regulator spring balance.

将手柄旋转到一定位置，使喷嘴挡板的距离在工作范围内，减压阀就进入工作状态中气室5的压力随喷嘴与挡板间距离的减小而增大，于是推动阀芯，打开进气阀口9，即有气流流到出口，同时，经孔道反馈到上气室4，与调压弹簧相平衡。

Manual valve to the slide-valve positioning means for positioning steel ball and spring structure of two kinds of reset.

手动换向阀的滑阀换向定位方式有钢球定位式和弹簧复位式二种结构。

When reassembling the check valves, make sure you install the correct spring into the correct check valve.

在重新组装止回阀时，要确保将正确的弹簧安装在正确的止回阀上。

It intergrates researching, manufacturing and selling together and specialize in producing spare parts of various types of cars,such as air brake parts, clutch booster, spring brake chamber, brake valve, relay valve and so on.It is one of the most important manufacturer of brake parts at home.

它集研发、制造、销售于一体，专业制造各种车型的气制动元件、离合器助力器、弹簧制动缸、手控阀、刹车总泵、继动阀等系列产品，是目前国内汽车制动元件的重要生产基地之一。

Used the simulation program to calculate abundant conditions, to simulate the brake capability and brake rule of F8 distribution valve which affected by various parameter, researched the main factor which affect the brake capability of F8 distribution valve, including the length of pipes, the elasticity of springs and the area and weight of pistons.

在此基础上，论文使用该仿真程序，进行了大量的仿真计算，对各种不同参数影响下F8阀的制动性能和制动规律进行了仿真分析，研究了影响F8阀制动性能的主要因素，主要包括连接管的长度、弹簧的弹力以及活塞的面积和重量等。

Inspection, screw open the cylinder high-pressure pipeline joints, using hand pump pumping pumps, fuel injection pump at the top of the case found that there is oil outflow tubing connector, the valve of the oil seal bad (of course such as a broken valve spring is also this would be the case), such as cylinder seals appear undesirable situation, it should conduct a thorough debugging injection pump maintenance, the replacement of dual pieces.

检查时，拧开各缸高压油管接头，用输油泵之手油泵泵油，如此时发现喷油泵顶部油管接头有油流出，则说明该出油阀密封不良（当然如出油阀弹簧折断也会出现这种情况），如多缸出现密封不良现象，则应对喷油泵进行彻底调试保养，更换偶件。

When the amount of fluid into the evaporator, the evaporator heat load is less than required, then the evaporator superheat steam export increases, the pressure is greater than the bottom of the top diaphragm pressure to force the diaphragm down so that bulge through the mandrel compression spring, and the valve pin to open the top, so that valve to open big holes are for fluid volume increase.

当进入蒸发器的液量小于蒸发器热负荷的需要时，则蒸发器出口蒸气的过热度增大，膜片上方的压力大于下方的压力，这样就迫使膜片向下鼓出，通过顶杆压缩弹簧，并把阀针顶开，使阀孔开大，则供液量增大。

Valve is the use of diaphragm, spring, piston and other sensitive components to change the valve clearance between the valve and valve seat, when the medium when produced by throttling, the pressure drop and its decompression valve.

减压阀是利用膜片、弹簧、活塞等敏感元件改变阀瓣与阀座之间的间隙，当介质通过时产生节流，压力下降而使其减压的阀门。

Kit consists of: Seat, Stem assembly, Spring, Two piston o-rings, Flow tube O-rings and Cover O-ring.

组件包括：阀座，阀杆总成，弹簧，两个活塞O形环，流量管O形环和阀盖O形环。

To burning the heavy oil in diesel locomotive, the injection unit must be adjusted, such as the clearance of piston, the spring character of unilateralism valve, the needle valve lift of injector and so on. At the same time, the parameter of injection, such as the injection advace angle, the injection time, should be adjusted according to the actual instance.

针对燃用重柴油的实际，需对柴油机喷射元件，如：喷油泵柱塞偶件间隙、出油阀弹簧刚度、喷油器针阀升程、及喷射参数，如：喷油提前角、喷油定时等均需作出调整，本文论述了具体的调整方法和依据。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。