弹性模量
- 与 弹性模量 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
The shear modulus and damp ratio characteristics of typical strata are achieved in the dynamic test, based on GDS triaxial dynamic system.
利用GDS三轴仪对工程场地内的原状土样进行了室内动力试验,获得了各主要土层的动弹性模量与阻尼比。
-
The influence of thedifferent parameters, such as blank-holder condition, thickness of blank sheetand material pattern on the wrinkle and the crack is analyzed. FLD is used tojudge the crack on the multi-point forming process successfully. The predictionof crack accords with the experiment ones, which shows choosing the properparameters can eliminate or restrain the defects, and also benefits the MPFtechnique and the shaping analysis.
本文对使用弹性介质和无弹性介质的多点成形过程进行了对比,指出使用弹性介质时在满足成形精度的前提下可以明显改善工件的成形质量,并通过对不同厚度和弹性模量的弹性介质对压痕的抑制作用进行了对比分析,探讨了最佳的弹性介质参数。
-
METHODS:Threedimensional finite element method was used to analyze the initial stress around screw implant of different elastic modulus and different diameter.
用三维有限元的方法对不同弹性模量和不同直径种植体植入后骨界面的初始应力进行分析。
-
The basic Arrhenius equation in the physical-chemical reaction is introduced to control the hydration process of the cement.
阐述了水泥水化反应遵循物理化学反应中Arrhenius方程的规律,用&等效龄期&的概念考查了温度对于混凝土弹性模量的影响,进行了某碾压混凝土拱坝施工期温度场的计算,并利用该温度场及&等效龄期&进行了应力场的计算,该应力计算中包含了温度及自重徐变应力。
-
For the characterization of the mechanical properties of thin films the Young's modulus plays an important role.
在薄膜材料的力学性能测定中,弹性模量是衡量材料软硬程度的重要指标。
-
Results indicate that the strength of infused resin is related to the strength of CFRP sheets, the influence of aging on Young's modulus and extensibility is slight.
结果表明,浸渍树脂抗拉强度与碳纤维片材抗拉强度有一定关系,而伸长率和弹性模量的变化受树脂耐久性能的影响不明显。
-
In this paper, the effect of Possion′s ratio, Young's modulus of core and shell, and inclination of core on the hydrofracture of core is analyzed.
分析研究了心墙与坝壳的泊松比、弹性模量以及心墙倾斜度等因素对心墙水力劈裂的影响。
-
The direction perpendicular to the transverse ridge of the goat condyle has the highest Young's modulus.
山羊髁突在垂直于横轴方向上的弹性模量最大,而在沿横轴方向上的剪切模量最大。
-
Using Young's modulus strength, or ultimate strain as dependent variables and strain rate and ap...
以弹性模量、强度和终应变为因变量,以应变率和表观密度或组织密度为自变量。
-
Compared with the traditional 2000 and 7000 series a-luminum alloys, 1420 Al-Li alloy decreases density by 12% and increases Young's modulus by 8%, and has excellent corrosion resistance and high temperature properties.
1420铝锂合金与传统的2000、7000系列铝合金相比,密度低12%,弹性模量高8%左右,具有优异的抗腐蚀性和高温性能。
- 推荐网络例句
-
But we don't care about Battlegrounds.
但我们并不在乎沙场中的显露。
-
Ah! don't mention it, the butcher's shop is a horror.
啊!不用提了。提到肉,真是糟透了。
-
Tristan, I have nowhere to send this letter and no reason to believe you wish to receive it.
Tristan ,我不知道把这信寄到哪里,也不知道你是否想收到它。