弯曲部分

Comparing with the case of no adit, because of arch tunnel set being broken; the intersection structure is subjected to combination of complicated stresses including transverse stress, but not the axial stress.

与无横通道情况相比，由于拱形支撑作用被切断，结构受力己不再是单一轴向受力，而产生了部分弯曲受力的复杂受力状况。

The method which is used to measure and compute moment, yield and turning angle by steel bar gauge is introduced in detail. According to the measuring results, the horizontal critical load of the testing pile is 120 kN. The steel bar gauge measuring results show that the largest moment is located in the depth from 2 m to 3 m under the horizontal load, it transfers to the deeper location with the increase of the horizontal load, and the bend distortion only occurs in the upper of 1/3 pile length.

结合实际工程详细地介绍了利用钢筋计测试水平荷载作用下桩身弯矩、挠度和转角分布的方法，根据桩顶位移和钢筋内力测试结果判定试验桩的水平临界荷载为120 kN；根据钢筋计测试结果可知，在水平荷载作用下，桩身最大弯矩截面位于在地面以下2～3 m处，且随着荷载的增大最大弯矩截面逐渐向深部转移；发生弯曲变形的部分主要是桩长1/3以上的桩体，而其下的桩体几乎不发生变形。

If it's back toward the arch, you could have problems with support and stability.

如果是在后面的足弓部分弯曲，你可能会有支撑和稳定性方面的问题。

PART 7 : DETERMINATION OF BENDING LENGTH.

第7部分：弯曲长度的测定。

Metal structure, the head is make by aluminum alloy material, the clockface is made by aluminum dial, the middle chain is made by stainless steel. You can bend it whatever as you want!

采用全金属结构，头部为铝合金材料，钟面采用铝制刻度面，中间部分是不锈钢制的链条，可以任意弯曲改变造型，N次创意，摆你所想！

Twisted, bent, or partially rolled upon itself; convolute .

旋转卷曲的自行旋转、弯曲或部分卷曲的；盘旋卷曲的

In traditional, the working probe naturally sustaining repeated bending actions and wear, absolutely needs a mechanism to prevent it from being damaged, caused by the change of the probe's geometry and the increase of the contact resistance. Therefore, in this study, we develop a CMOS-based chip in connection with the electroformed probes to detect each of their counterforce, contact resistance to evaluate if their contact force and coplanarity are controlled within safe range.

传统上，探针常因为弯曲作动和磨耗，使几何形状产生改变，进而电阻值提升，使过大的电流通过探针而烧毁，或因共面度不佳部分探针未能确实接触IC焊垫误判成断路，故晶片的制作重点在於监测探针卡上个别探针的回馈力量，当探针量测IC时，可进行即时探针反作用力、接触电阻的检测，进而了解探针卡工作时受力是否均匀、平坦度是否符合要求等性质。

It is shown that the strengthening mechanisms came from many aspects, including the tension and compression of crystal planes, the bending and distortion of crystal lattices, the increase of dislocation density, the formation of cellular dislocations, the transformation of part of the residual austenites.

以300M超高强度钢为例，运用多种测试手段，如TEM、SEM、XRD以及金相分析技术，发现强化层组织中晶面的拉伸和压缩，晶格的弯曲和歪扭，位错密度的增高，胞状位错的形成，部分残余奥氏体向形变马氏体的转变等现象，在综合分析的基础上指出，位错强化是抗疲劳增寿的主要因素。

The 1,224 parts were carefully rebuilt into a splendid, narrow boat with a curved hull, rectangular deckhouse and long oars.

在1224年部分仔细重建成一个辉煌的，狭隘的船船体的弯曲，矩形甲板室和长期掉以轻心。

For example, the roll elastic deformation breaks the statically determinate condition of roll system in duo mill, and this is the main reason of bearing longevity shortening and burning accident; in aluminium foil four-high mill roll system with a 1 mm gap, the ideal position kept by a 3 mm offset is out of effect, some phenomenon such as chock horizontal vibration, gyroscopic effect and micro dimensional dynamic cross happen in fact rolling process, abnormal super and partial load resulted by these is the main reason of the end thrust bearing accident; the thermal deformation of mill roll system accompanying the temperature raising not only changes the roller track age of rolling bearing, but also results a micro dimensional slow dynamic inverse cross that counteracts the gyroscopic effect in a degree.

如二辊高刚度轧机轧辊的弹性弯曲微尺度行为，破坏了辊系机构杆系的静定条件，成为轧机轴承短寿烧损的主要根源；铝箔四辊轧机只具有1mm的有隙辊系，凭借设置3mm偏移距和轧制力平衡产生的水平力以保持轧辊理想定位失去效用，却发生轴承座水平振动现象、陀螺效应和动态交叉微尺度行为，成为止推滚动轴承异常超偏载导致短寿烧损的主要根源；轧机辊系的伴随升温产生的热变形，不仅改变了滚动轴承滚道轮廓，还引起运动副内慢变动态反交叉微尺度行为，抵消陀螺效应的部分动态交叉角度。

With Death guitarist Schuldiner adopting vocal duties, the band made a major impact on the scene.

随着死亡的吉他手Schuldiner接受主唱的职务，乐队在现实中树立了重要的影响。

But he could still end up breakfasting on Swiss-government issue muesli because all six are accused of nicking around 45 million pounds they should have paid to FIFA.

不过他最后仍有可能沦为瑞士政府&议事餐桌&上的一道早餐，因为这所有六个人都被指控把本应支付给国际足联的大约4500万英镑骗了个精光。