张力

As the temperature of rat aorta was raised, the vasoconstrictive force and vasoconstrictive speed increased, and the effects of norepinephrine on vasculature were raised. The results suggest that the constant X1 for vasoconstrictive force is a factor sensitive to temperature.

认为NE引起的血管收缩张力的大小，显然也处于温度的影响之下；随着温度的升高，血管收缩张力变大，收缩速率变快，NE对血管的作用效力增强；且张力因子X1是温度敏感因子。

To verificate the correctness and reliability of the simulation system, a typical processing of 3 rollers stretch reducing of tube is simulated by simulation system of 3D Thermo-mechanical Couple rigid-plastic FEM.

为验证作者开发的&钢管张力减径三维热力耦合刚塑性有限元虚拟仿真集成系统&的正确性和可靠性，对典型的三辊张力减径过程进行了模拟，并将模拟结果与产品实测结果进行对比，结果证明了采用有限元模拟技术能够为钢管张力减径工艺制度制定和轧辊孔型优化提供依据。

Characteristics of Ten-Roll Tube Straightener;2. Ultimate strength of short steel tube-confided concrete;3. To verificate the correctness and reliability of the simulation system, a typical processing of 3 rollers stretch reducing of tube is simulated by simulation system of 3D Thermo-mechanical Couple rigid-plastic FEM.

为验证作者开发的&钢管张力减径三维热力耦合刚塑性有限元虚拟仿真集成系统&的正确性和可靠性，对典型的三辊张力减径过程进行了模拟，并将模拟结果与产品实测结果进行对比，结果证明了采用有限元模拟技术能够为钢管张力减径工艺制度制定和轧辊孔型优化提供依据。

METHODS: Eight fresh patellae specimens were divided into two groups at random, AO steel wire group (n = 2) and absorbable tension band group (n = 6) to create models of transverse fractures, which were separately fixed by absorbable tension band, steel wire tension band + Kirschner wire to measure their biomechanics function. If fracture gap reached 1.0 mm, the fixation failed.

随机分成AO钢丝组2个和可吸收张力带组6个，制成横断骨折模型，分别用可吸收张力带、钢丝张力带加克氏针进行内固定，测定它们的生物力学性能，骨折端分离1.0 mm为固定失效。

Adnjacent tassion, which is the ability to change printer material tension values that are separated by the parts, the parts include: installation of electrical engineering, clutch and brake disk for an open-book and complex helps feed and discharge tension roll, and so on.

相邻的不不不张力区是由不妨分明保留承印质料不不不张力值的部件不分隔的，此类部件主给包含：安设有电机、即分器及刹车盘的不闭卷和双卷轴，进料与不入料不不不张力辊等。

Theconstant control device of adjusting wire tension with two wire winding drum s is studied on the basis.

分析了高速走丝线切割机使用重锤式恒张力机构存在的缺点，在此基础上研究了一种能够实现调节电极丝张力的双贮丝筒恒张力控制装置。

The ten day due to the pressure of ink printing pressure or debugging roller pressure caused by improper ink.

不张力不朱杠旬由于印版不张力或网纹辊不张力调试不妥引起的不朱杠。

When passing water roll manual pressure chinsang water roller test pressure, the pressure to find a bigger point, and they are being built by chromeplating hard iron roller, too much stress borne water roll like a frame on the same series water rolls, resulting in a biography of the shaft and water roll and bucket motor drive gear does not match the space is large, it will be some operation.

当把传水辊手不静压上串水辊尝试不张力时，发掘两者之间的不张力不小了不面，而它们都是经过镀铬的软铁辊，过不小的不张力会使传水辊像架在串水辊上不同，导致传水辊轴脚与水斗电机传不静齿轮不匹配，间隙较不小，运转时不离会有些颤不静。

Block or cylinder precision is not enough, in a circle and nano-imprint lithography drum mesh, plates and substrate contact pressure too uneven, the color of ink; pressure to produce color on the hour, the ink.

印版滚筒精度不敷或不方，在与压印滚筒啮合时，印版与承印物的隔绝不张力不平均，不张力不小时，爆发颜色不不深的不朱杠；不张力小时，爆发颜色不不深的不朱杠。

The inefficiency problem during cold rolling of titanium sheet without tension exerted on it was investigated. The state equation of stress of titanium sheet under tensional effect is deduced on the basis of Hill's anisotropic yield criterion in combination with the anisotropic characteristics of titanium s mechanical properties.

针对钛板在无张力条件下冷轧效率低下的问题，首先结合钛材力学性能各向异性的特点，以Hill异性屈服准则为基础，推导出钛板在张力冷轧下的应力状态方程，从而在理论上阐明，钛板在张力条件下进行冷轧的可行性主要取决于其塑性变形条件及其所处的应力状态。

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。