引导

On the other hand, if the DQ3 is "1", then all the sectors except the boot block are programmed/erased inhibited.

另一方面，如果DQ3是"1"，那么所有的部门除了引导块进行编程/擦除抑制。

If the DQ3 is "0", it means the #WP pin is in high state, then all the sectors except the boot block can be programmed/erased.

如果DQ3是"0"，这意味着＃WP引脚在高状态，那么所有的部门除了引导块可以编程/擦除。

The entire memory array will be erased to FF by the chip erase operation if the boot block programming lockout feature is not activated.

整个存储器阵列将被删除到FF的芯片擦除操作，如果引导块编程锁定功能没有激活。

The 16 Kbyte Boot Block can be used for small initialization code to start the microprocessor, the two 8 Kbyte Parameter Blocks can be used for parameter storage and the remaining 32K is a small Main Block where the ap- plication may be stored.

16字节的引导块可以用于小型的初始化代码用于启动微处理器，两个8字节的参数块可用于参数存储和使用，其余32K的主楼是一个小地方的AP -折叠术可以被保存。

If the boot block programming lockout is activated, only the data in the other memory sectors will be erased to FF while the data in the boot block will not be erased (remains as the same state before the chip erase operation).

如果引导块编程锁定被激活时，只有在其他部门的数据存储器将被删除到FF，而在启动块中的数据不会被删除（仍然是以前的芯片擦除操作）相同的状态。

But the hardware protection will override the software lock setting, i.e., while the #TBL pin is trapped at low state, the top boot block cannot be

但是，硬件保护锁将覆盖软件设置，即，而＃任务型脚在低的境地，前引导块不能

Second, hot-swappable law, if more serious damage, even the Boot Block damage to guide the block together, you can try "hot swap" to repair.

二是热插拔法，如果损坏比较严重，连Boot Block引导块也一起损坏，可以试用"热插拔"来修复。

First, the use of "BIOS BOOT BLOCK guide block" to restore, normally there is a BIOS will not be set to retain part of that process BOOT BLOCK, even if the BIOS update failure, Boot Block, or to control ISA card and floppy drive.

一是利用"BIOS BOOT BLOCK引导块"恢复，通常情况下BIOS中会有一个保留部分不会被刷新，那就是BOOT BLOCK程序，即使BIOS刷新失败，Boot Block还是能够控制ISA显卡与软驱。

X60008EIS8-50 Pinout: In order to detect whether the boot block feature is set on or not, users can perform software command sequence: enter the product identification mode (see Command Codes for Identification/Boot Block Lockout Detection for specific code), and then read from address 7FFF2.

X60008EIS8-50引脚说明：为了检测是否启动区块功能或没有设置，用户可以进行软件的命令序列：输入产品识别模式（见识别/引导块锁定检测特定的代码指令代码），然后从地址7FFF2阅读。

What will happen if Partition Boot Sector is damaged or bad/unreadable?

会发生什么事，如果划分引导扇区损坏或坏/unreadable？

But we don't care about Battlegrounds.

但我们并不在乎沙场中的显露。

Ah! don't mention it, the butcher's shop is a horror.

啊！不用提了。提到肉，真是糟透了。