应用力学

By using wave mechanics , the process of impact driving pile is analyzed,and a mechanics mode of impact driving system which consists of hammer spring cup and pile is established.

应用波动力学分析了冲击沉桩过程，建立了由冲锤、桩帽和桩组成的冲击沉桩系统的力学模型，研究了冲锤重量、桩帽刚度和桩波阻抗对效率的影响，在此基础上，提出了冲锤、桩帽和桩的最佳方案。

Compared with the Epoxy resorcinol-formaldehyde resin pretreatment system and Maleic anhydride pretreatment system developed by Xusigui, the 40% carbolated styrene-butadiene latex system can keep the composite"s properties and reduce the cost of pretreatment and simplify the pretreatment technology; especially to the HST 2073 latex system, the composite"s mechanics properties are improved greatly. Secondly, the composite"s comprehensive properties and interface performance are improved by reinforced with short fiber grafted with rubber in the surface. Thirdly, to simplify the production technology of composite, we add TKM-M and RF-90 as adhesive agent to the composite blended in an internal mixer, so as to the composite can be used to industry widely, then the effect of the amount adhesive agent on the composite"s properties and interface adhesive performance was studied, from the experiments the optimum amount of adhesive agent was deduced.

其中采用特软羧基丁苯胶乳预处理短纤维的方案，降低了预处理成本，相对许泗贵的低分子环氧和马来酸酐体系来说，预处理工艺大大简化了，而材料的力学性能保持良好，尤其是 HST 2073A 胶乳预处理体系，力学性能有较大幅度的提高；第二，通过对尼龙短纤维表面进行接枝橡胶分子链预处理，改善了复合材料的界面粘合性能，复合材料的综合性能也得到了相应的提高；第三，为了简化复合材料的生产工艺，使复合材料的应用得到工业化推广，我们选用TKM—M和RF—90长效增粘剂，直接加入短纤维橡胶复合材料中，采用密炼工艺，探讨了增粘剂的用量对复合材料界面粘合以及性能的影响，得出了增粘剂在复合材料中的最佳用量。

objective: to investigate diagnosis and treatment choice of detrusor hypoactivity with impaired contractile function on voiding function in benign prostatic hyperplasia.methods:the clinical date of 48 bph patients with dhic were analyzed,including clinical diagnosis,urodynamic parameters,treatment and follow-ups.results:37 patients with detrusor instability and over 40 cmh2o bladder pressure were treated successfully by turp.the time of indwelling suprapubic punctural cystostomy cathter was(1~8)weeks.11cases without di and under 40 cmh2o bladder pressure were treated by suprapubic punctural cystostomy,accepted the test of urodynamics after(1~3)months.7 cases with di were treated successfully by turp,4 cases without di were indwelled suprapubic punctural cystostomy cathter all life.conclusion:dhic worsens the voiding function of the patients with bph,and the test of urodynamic is helpful to diagnose and could provide more convinced evidences for treatment of patients.

分析膀胱过度充盈所致逼尿肌损伤，引起膀胱逼尿肌收缩无力良性前列腺增生48例患者的临床资料，包括诊断，尿动力学检查，治疗及随访结果。结果：37例经尿流动力学检查，诱发存在逼尿肌不稳定，伴膀胱内压达40 cmh2o以上，采取turp，术后留置膀胱造瘘管（1~8）周后全部拔除，排尿通畅。11膀胱内压始终未达到40 cmh2o，且在膀胱注水充盈过程中无逼尿肌不稳定出现，行膀胱造瘘后出院，（1~3）个月后经尿动力学检查复查膀胱逼尿肌收缩力，其中7例膀胱逼尿肌收缩功能有恢复，行经尿道前列腺汽化电切术治愈；剩余4例膀胱逼尿肌收缩功能几乎无任何改善。长期留置膀胱造瘘治疗。结论：良性前列腺增生导致膀胱过度充盈所致逼尿肌损伤，引起膀胱逼尿肌收缩无力患者，术前应用尿流动力学检查对膀胱逼尿肌损伤程度进行认真分析，可进行有针对性的治疗。

In order to analyze the influence and damage of the top and bottom of rock mass in floor water-resisting layers due to water pressure in water bearing layer and mining pressure, this paper applies the methods of similar material simulation test and mechanical analysis of floor water invasion in the near of faultage to further comprehend the mechanism of floor water invasion.

为了分析底板含水层水压及采动矿压对底板隔水层岩体上部与下部的影响与破坏，应用了相似材料模拟试验以及断层附近底板突水的力学分析方法，对底板突水机理有了进一步的认识；同时，由断层附近底板突水的力学分析方法所得到的理论计算结果，也可以作为判别类似条件下遇断层时承压水体上采煤是否安全的依据。

Through designing of composition and structure of the bioactive graded coating,innerstress and its distribution in the coating were analyzed and calculated, the resultsshowed that when composition distribution coefficient n was 1.5, a reasonable stressdistribution could be got, that was at the beginning of deposition the suspension containingrichly BG granules was used so that a rich BG granules layer, a good transitional layerbetween BG layer at the bottom and the coating could be obtained at the titanium alloy side,the bottom of the coating; the stress value near the interface and surface and its character,pressure stress or tensile stress, were decided by the character of its composition itself.Changing composition distribution coefficient n could only change the variation tendency ofstress in the coating, but did not change the stress distribution rule in the coating. Thethinner the coating is, the sharper stress variation in the coating is, which does not mean thatthicker coating is better because the thicker the coating is, the little the permitteddeformation of coating is, so the coating thickness should be thinner, for example, about50μm for bending applications, but for applications only bearing pure shear stress, such asroot of tooth implant, the coating can be thicker little, for instance, about 80～100μm. The study on electrification characteristic and electrophoresis deposition of HAand BG granules in aqueous and non-aqueous solution system found that EPD almost didn'toccur in aqueous solution system. However, because HA granules take position charges inabsolute alcohol, a homogeneous EPD be carried out on the cathode titanium alloy slice, but taking negative charge in absolute alcohol the BG granules not be deposited on the cathode. A guided HA crystallizing, 100～300nm, on surface of the BG granules be realized by metathetical reaction, which cover BG granules with HA microcrystals and make the covered BG granules taking position charges in absolute alcohol, sequentially realize the EPCD of the BG and HA granules on the cathode, so it is feasible to make a titanium alloy/BG/HA bioactive graded coating by making use of EPCD technology. The corrosion experiment of rich boron bioglass coating and plasma spray coating showed that split phase, rich boron and rich silicon phase, occurred during its preparation. In basic medium the corrosion behavior of 〓 BG coating showed uniformity corrosion, the corrosion mostly occurred at rich boron phase area, therefore batch formula design of BGshould avoid the occurring of split phase. The corrosion appearance of plasma spray coatingappeared a non-uniform corrosion, mostly occurred at the edge of the laminated HA moltendrops, and emerged an accelerated corrosion tendency, which will easyly lead to corrosioncrackles extending to the interface and the happening of osmotic interfacial corrosion, thatmay be one of the major reasons leading to the coating cracking-off in the later period. Thetesting results of thermal expansion coefficient of 〓 and 〓BG showed the thermalexpansion coefficient of 〓 BG matched with that of titanium alloy better, and 〓 BG couldsinter with titanium alloy into densification enamel layer at low temperature (720℃).

将Ti6Al4V合金在1000℃下进行真空热处理会降低其力学性能，且合金内的V元素会向表面富集，因此，钛合金真空热处理和表面涂层的烧结温度不能过高，即应低于其相转变点；通过对生物活性梯度涂层的组成和结构的设计，分析和计算了梯度涂层内的应力大小和分布，结果表明：对于本研究，当成分分布系数n=1.5时，可以获得较合理的涂层力学性能，即在沉积开始时，采用富含BG颗粒的悬浮液，以便在钛合金侧获得同底层BG有良好过渡的富BG涂层；梯度涂层界面和表面的应力大小、性质由材料组成本身的性质决定，改变成分分布系数，只能改变涂层内应力变化的趋势；涂层的厚薄不影响涂层内的应力分布规律，但涂层越薄，涂层内的应力变化越快，但这并不意味着涂层越厚越好，因为涂层越厚，涂层允许的变形越小，对于应用于弯曲受力部位的涂层而言，涂层应薄一点为好(50μm)；而对于仅纯受剪切应力的部位，如牙根种植体，涂层可适当加厚(80～100μm)；通过对HA和BG颗粒在水溶液体系和非水溶液体系中的带电特性和电泳沉积的研究发现，它们在水溶液体系中很难发生电沉积；在无水乙醇溶液中，HA颗粒带正电，可在阴极钛合金片上发生均匀的电泳沉积，而BG颗粒则带负电荷；利用复分解反应法，可以制得100～300nm的HA，通过诱导HA在BG颗粒表面结晶，可对BG颗粒进行表面包覆，获得了被HA包覆的BG颗粒，改变了BG颗粒表面的带电特性，使BG和HA颗粒在无水乙醇中均带上正电荷，从而实现了HA和BG颗粒在阴极上的共沉积。

The purposes of this thesis are focused on the finite element biomechanical analysis, which contains surface mesh optimization and biomechanical analysis of Nuss pectus excavatum repair.

本论文之目的，在於研究有限元素法於生物力学分析上之应用，研究内容包括了表面网格最佳化以及纳氏漏斗胸手术之生物力学分析。

The relationship between the Riemannian geometric framework of Lagrange equation and the topology graph representation of classic mechanical systems is discussed.

讨论了经典力学系统中拉格朗日方程的黎曼几何表示和力学系统拓扑图表示之间的关系，作为应用。

He data and information of photomechanics are often represented by optical interferometric 〓ringe patterns. The first major contribution of this dissertation is study on fringe pattern 〓utomatic processing.It is significant in techniques and engineering applications to reduce noise and recovery 〓he phase of interferometric fringe pattern.

光测力学的实验数据和信息，都是用光学干涉条纹图来表示的，因此本文首先侧重于用数字图像处理技术，对光学干涉条纹进行自动处理的方法与技术的应用研究，这对于从光学量进一步获得正确的力学量数据的作用是十分重要的。

The difference of micropolar elasticity from classical continuum is that the former incorporates micro-rotation in its deformation formulation and couple stresses in its stresses.

本文综述了碳纳米管国内外研究现状及进展，然后在总结前人研究成果的基础上，应用适合于研究微观力学的微极性弹性理论和非局部弹性理论对碳纳米管的静力学、屈曲以及动力学性能进行了研究。

Applied overlay principle discloses intention at the complex load of break of grease wall of a well for individual and simple load, through set and time relevant aeriform pressure distributings function, rupture according to flexibility of stretch and mechanical, line condition of tie of stress of the upland after perforation of well of grease of mechanical and academic derivation plays factor of intensity of interstitial and most advanced stress, got deflagrating patulous condition is cracked since terrane of aeriform fracture wall of a well, the aeriform pressure gradient that this condition can follow time change inside reflective break is right the influence of interstitial configuration.

应用叠加原理将功能于油水井壁裂缝的复杂载荷分解为单个简单载荷，通过设定和时间相关的气体压力分布函数，根据弹性力学、线弹性断裂力学理论推导油水井射孔后高地应力约束条件下裂缝尖端应力强度因子，得到了爆燃气体压裂井壁岩层起裂扩展条件，该条件可以反映裂缝内随时间变化的气体压力梯度对裂缝形态的影响。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了