应力轴

Through analyzing the result, we can draw a conclusion that it is an effective way to increase the thickness of crank web than to increase the shaft diameter by the way which improves the rounded stress of the crankshaft from structural.

通过对计算结果的分析，得出在结构上改善曲轴过渡圆角处应力集中时，增加曲柄臂厚度与增加轴颈直径是较有效的方法，为某增压发动机曲轴的结构设计提供了理论依据。

Based on the relations among the stress, final wall-thickness of thin-walled tube and the characteristics of tube material, original size, curling radius along with friction condition in a axially-compressed internal inversion process on right-angled fillet die, some analytical discriminants were established for judging if a double-layered tubular piece of aluminum alloy could be steadily formed from a certain-sized round tube via internal inversion process without interference and plastic instability of tube wall, and a method was put forward for determining the maximum and minimum usable curling radius or die fillet-radius for thin-walled tubes in the process.

基于薄壁管直角圆角模轴压内翻过程中各处应力及最终壁厚与管材特性、管坯尺寸、卷曲半径及摩擦条件之间的关系，推出了判别任一铝合金双层管件可否由特定尺寸圆管稳定内翻成形而不出现管壁干涉与塑性失稳问题的解析判别式，指出了确定薄壁管圆角模内翻卷曲半径或模具圆角半径极限值的方法。

At the same time, for the polishing plate of diamond film with the same thickness, von Mises equivalent stress and the radial displament show a ascending tendency with the increase of rotating speed, but the axial displacement firstly increases and then decreases.

同时，对于同一厚度的金刚石膜抛光装置，随着转速的提高，von Mises等效应力和径向位移呈现相似的上升趋势，轴向位移却先上升后下降。

Based on Tseng-Lytton evaluation model for permanent deformation, and evaluation model for permanent deformation of clayed subgrade soils is established by improving and calibrating Tseng-Lytton model.

利用室内重复荷载三轴试验，研究了在含水量、压实度和偏应力影响下粘性路基土的永久变形特性，并以Tseng-Lytton路基土永久变形预估模型形式为基础，对Tseng-Lytton模型进行了改进和标定，建立了粘性路基土的永久变形预估模型；最后利用分层应变总和法，并结合一个典型粒料柔性基层沥青路面结构实例，计算了路基土的永久变形量。

Methods The third-passage chondrocyte were harvested from the mandibular condyles of 2-day-old rats, and a cellular compressive stress device was used to apply stress on cells at 4 000 Ixstrain for 15, 30, 60, 120, 240 min.

方法利用四点弯曲加力装置对第3代大鼠髁突软骨细胞进行周期性单轴压应力加载，力值为4000μs train，时间为15、30、60、120、240min。

The tests show that it's quite essential to confirm the mechanical properties of rock with the triaxial test fitting the stress change of acutal engineering.

试验研究结果表明通过符合工程实际应力变化的三轴试验确定岩石的力学性能参数是很有必要的。

In the present study, through using non-linear three dimensional finite element analysis, considering the contact in flange to nut and flange to gasket, we accurately computed the stress distribution in the flange joint in the normal work condition.

采用ANSYB软件，应用三维有限元技术，考虑了垫片的非线性和法兰和螺母、垫片的接触问题，并且采用了螺栓预紧单元，准确计算出法兰连接在承受内压、轴向力和弯矩外荷载时的应力分布。

The results show that the friction between hoop cable and joint will cause tension redistribution in hoop and radial cable of structure,led to uneven force distribution of the same hoop cable,increase displacement of some joints and axial stress of some bars in the lattice shell, and static properties of the structure will be obviously affected,but the dynamic and stability characteristic almost will not.

计算结果表明，环索与节点间的摩擦会导致结构环索及斜索张力重分布，致使同圈索力分布不均匀，使部分网壳杆件轴向应力和节点位移增大，对结构的静力性能影响最大，而对动力和稳定性能基本没有影响。

Based on lubrication analysis of journal bearing, the stress distribution of shaft was calculated by using film pressure that calculated as boundary condition of load.

在轴承润滑分析的基础上，将得到的轴承油膜压力作为载荷边界条件，计算了轴的应力分布。

By analyzing the influence of hemisphere pits with different dimension and ellipsoid pits with different aspect ratio on stress and strain distribution of lap joint, the possible propagation of fatigue crack was discussed, and the effects of localized pitting corrosion on the structural integrity of lap joints were discussed.

通过分析不同尺寸的半球形蚀坑和不同长短半轴比值的半椭球形蚀孔应力应变分布的影响，探讨搭接件疲劳裂纹的可能扩展方向，讨论局部孔蚀对搭接件结构完整性的影响。

In the United States, chronic alcoholism and hepatitis C are the most common ones.

在美国，慢性酒精中毒，肝炎是最常见的。

If you have any questions, you can contact me anytime.

如果有任何问题，你可以随时联系我。