应力轴

A general-purpose software for the analysis of the rotor integral stress has been designed,which can be employed not only for a complicated rotor incorporating both radial and axial pretightenning,but also for a rotor with any arbitrary axisymmetrical structures.

给出了通用计算方法，并设计了组合转子整体应力分析的通用软件。该软件不但适用于具有径、轴双向配合的复杂转子，还适用于任意轴对称结构。

In the present thesis, the solution of axisymmetrical space full plastic problems of ideal elastoplastic material is proposed from the fundamental equations, the possibility of using Tresca's yielding condition and the influence of longitudinal stress are discussed therefore the analytic formulae of plastic strain are also derived.

本文从轴对称空间问题的基本方程出发，研究了理想弹塑性材料塑性加载时的一般解法，讨论了采用各种形式Tresca屈服条件的可能性及轴向应力对于它的影响，并导出了塑性应变的解析式。

When the burring process of 12×4J wheel is processed taking the deformation area as the plane stress condition,the deformation characteristics of normal and radius directions are studied,which is influenced by the factors such as height and the inner hole initial radius and the deformation law of circle strain.

利用斜冲模对12×4J轮辐进行翻边时，将变形区看做是平面应力状态，探讨了翻边高度、初始孔径及斜冲模角对翻边变形区径向应变和轴向应变的影响，对12×4J轮辐翻边不同斜冲模角下的冲压力变化规律进行了计算。

The technology doesn't stop at the circuit board, with a high performance coreless motor, dual ball bearing supported output shaft, bushing supported gear shafts and a Heavy Duty Metal gear train this servo was designed to withstand the stress of on/off road vehicles.

该技术并不停留在电路板，高性能芯电机，双球轴承支持输出轴，衬套支持齿轮轴和重型金属齿轮火车，这是伺服设计足以承受的应力/断道路车辆。

After thermal cycling testing, when the strength of equiaxial grain regions or thermally grown oxidation layer became lower than the shear stress, the spallation occurred along the vertical crack network.

经过长时间热循环后，当陶瓷层等轴晶区的强度或者热氧化生长层的强度小于边缘效应产生的剪应力时，涂层在试样的中部以垂直裂纹网格形状发生剥落失效。

In this program, the declining segment of the stress-strain relation of the concrete, the restriction effect of hooped reinforcement and the bond-slip problem of the reinforcement are considered, as the same time the optimized arithmetic is applied to accelerate calculation procedure. Though the appropriate experiment arrangement, the influential factor such as the strength of concrete, the ratio of hooped reinforcement, the ratio of axial compression and the loading angle are researched, some available rules of carrying ability and ductility of the special-shaped column can be attained.

程序中考虑了混凝土应力应变曲线的下降段及箍筋对混凝土的约束影响，采用了合适的算法加速计算过程并考虑了纵筋锚固滑移的影响，通过正交试验分析了混凝土强度、体积配箍率、轴压比和荷载角对异形柱截面抗弯承载能力及截面曲率延性比的影响。

The finite element analysis of an existed hydroturbine thrust bearing support are presented in the paper.

本文对水轮机推力轴承支架进行了有限元分析，为改善应力分布、减小轴向位移和节省材料，对其作了优化设计

OBJECTIVE: To quantify the stress distribution on the intervertebral disc, interarticular process and iliolumbar ligament of the lumbar vertebrae.

目的：观察轴向载荷下L5~S1上关节突与下关节突之间的峡部、椎间盘和髂腰韧带的应变和表面应力情况。

On base of analysis to simulation result, it was point out the main cause making dissimilar metal"s bonding so difficult was metal"s inharmonic plastic deformation. The distribution and changement of stress and strain on interface and in workpieces were analyzed.Making use of experiment and simulation result, main factors that influence welding property of cold pressure welding were discussed.

通过对模拟结果的分析，说明了异种金属冷压焊较同种金属冷压焊困难的原因主要是界面处两种材料的径向和轴向的不协调塑性变形；直观地显示了冷压焊过程中工件内部及界面处的应力应变分布及变化情况。

In the cases of clubfoot, wire-cutting of the matatarsal bones was found in 33.33%, rigidity of the intertarsal joint and pin tract infection in 55.56% and 77.78% respectively.

克氏针足够张力和改变引起下肢出现外翻应力的姿态以及对严重短肢畸形分次延长可减少轴向偏移和肌肉关节挛缩。

In the United States, chronic alcoholism and hepatitis C are the most common ones.

在美国，慢性酒精中毒，肝炎是最常见的。

If you have any questions, you can contact me anytime.

如果有任何问题，你可以随时联系我。