应力

Second, by analyzing the strain of northsouth blocks of the fault, we find an asymmetric displacement distribution between the two sides of the rupture, and the two blocks are subject to compressional and tensional stress respectively. It is a pattern that cannot be explained with the linear elastic theory. However, laboratory experiments and in situ measurements in boreholes have shown that many crustal rocks exhibit a nonlinear elastic behavior in compression and tension with a dependence of the Young's modulus on the minimum principal stress. So we suggest that the nonlinear displacement distribution should be considered when dislocation and hypocentral parameters are analyzed.

进而通过对地震南北盘同震应变的分析，发现了昆仑山地震的南北两盘分别受挤压和拉张两种应力作用，研究表明多种岩石在拉张和压力作用下其最小主应力下的杨氏模量表现出非线性弹性特征，从而提出对昆仑山地震地表位移及震源特征参数分析时应考虑非线弹性介质导致的非线性弹性位移分布特征。

The mixed boundary problem was reduced to a system of singular integral equations by means of Fourier transform.

利用Fourier积分变换技术将混合边值问题转化为一对奇异积分方程，通过数值求解奇异积分方程获得含裂纹功能梯度板条分别在剪切和法向载荷作用下的I型和Ⅱ型应力强度因子，并讨论了材料的非均匀性和裂纹相对尺寸对裂纹尖端应力强度因子的影响。

With the temperature and strain increasing, modulus of elasticity of steel gradually decreases.

结果表明，钢材的应力－应变曲线随温度升高，应力变小而应变增大，曲线斜率即弹性模量随温度升高和应变增大而趋于零。

The monotone property of multivariate function proved that the maximum stress strength point exists on the inner surface of

应用多元函数单调性理论，证明了在三轴应力条件下管体中最大应力强度值出现在套管内壁。

Second, thestress-type ABC indicates that the ABC is an expression of interaction stress betweenthe near-field finite domain and the far-field infinite domain. It can compatible withthe finite element method very well as a natural stress boundary condition, leading tothe numerically stable near-field wave motion method.

其次，应力型指人工边界条件是有限域和无限域间相互作用应力的表达式，其作为自然边界条件较好地兼容有限元法，易于形成稳定的近场波动分析方法。

In this paper, the negative land angle s of PCBN tools was determinedwhen the cutter was used to cut hardened steel.

本文研究了PCBN刀具负倒棱前角的合理选择，并用X射线衍射仪测量了加工表面残余应力，分析了负倒棱前角在形成表面残余压应力过程中的作用。

It was found by the stress nephogram analysis that the maximal stress of V-notch column sample only exist at tip where the V-notch lies and this will do good to Q235s regular fracture.

通过分析试样的ANSYS应力云图可得：V型切口试样的最大应力仅仅出现在切口尖端，这对Q235的规则断裂创造了条件。

The casing strength is analyzed and displacement nephogram and stress distribution nephogram of the casing are obtained. The results show that the direct reasons causing the casing crack are local stress concentration and inadequate material strength.

通过分析得出箱体的位移分布云图和应力分布云图，结果表明箱体出现裂纹故障的直接原因，是箱体局部应力集中，材料强度不够。

The influence of the material Poisson's ratio on the strain, stress and neutral plane in the direction perpendicular to the magnetization is prominent, but insignificant for the stress, strain and the neutral plane in the direction of magnetization, and further, its role can be neglected.

材料泊松比对垂直于磁化方向的应力和应变以及中平面的影响很大。但是，泊松比对磁化方向的应力，应变和中平面的影响很小，可以忽略。

The results show that structure curvature is negatively related to coalbed gas content,relative gas emission rate,outburst gas and coal amounts which reflect No15 coalbed of Ji is above the neutral plane of folds.That is,the No15 coalbed of Ji Group is compressed in incline and is tensed in anticline,and the higher structure curvature is,the higher stress is.

结果表明，构造曲率与瓦斯含量、瓦斯相对涌出量、突出瓦斯量、突出煤量呈负相关关系，反映研究区己15煤层位于褶皱中和面以上，即煤层在向斜轴部受挤压而背斜轴部受拉张，正曲率值反映煤层受到拉张应力作用，负曲率值反映煤层受到挤压应力作用，曲率绝对值越大，受力越大。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。