应力

The fatigue reliability analysis for the 16V240ZJB diesel engine crankshaft inserving DF4B internal-combustion locomotive were carried out in thisdissertation.Firstly,according to the fatigue loads of the crankshaft,the bendstress and torsion stress at danger zone in rated operation modes werecalculated respectively.The stress randomicity of the crankshaft was analyzedrelating operation modes of acceptance,and the probability distribution ofstresses were obtained with statistical analysis.

运用本文所提出的疲劳可靠性分析模型(干涉模型-Miner准则综合法及弯扭复合模型)和经分析简化得到的材料p-S-N曲线和p-Sa-Sm-N曲面，分别按一维、二维疲劳应力及弯扭复合应力三种情况对东风4B型内燃机车16V240ZJB柴油机曲轴进行了疲劳可靠性分析。

Author regards topography's effect on underlying horizon rock formation as distributed load, thus obtains expression of subsidiary stress induced by distributed load by integral action.

山体对其下伏岩层可作为分布载荷，对集中力作用下水平岩层中各应力分量积分，便求得山体对下伏水平岩层的附加应力。

Asymmetrical dynamic propagation problems under the action of variable loads and (P^3t/x^2) located at the origin of the coordinates respectively, are resolved by the measures of self-similar functions, and the universal expressions of analytical solutions to stresses, displacements and stress intensity factors are gained.

采用自相似函数的方法对坐标原点分别受到变载荷Px/t、Pt^3/x^2作用下的非对称动态扩展问题进行求解，获得了应力、位移和动态应力强度因子解析解的一般表达式。

The potential functions of incident and scattered waves were expanded into Fourier-Bessel series, and the coefficients of scattering waves field were determined by imposing continuity conditions of stress and displacement at the soil-pile interfaces with the help of a set of cylindrical coordinate systems and in accordance with the Graff's addition theorem.

将倾斜入射波和散射坡的势函数展开成Fourier-Bessel函数的无穷级数的形式，利用一组圆柱坐标系统和Graff加法转换定理，通过施加桩土界面处的应力和位移连续的边界条件，求解出散射波势函数的待定系数，进而得到饱和土体中任意点的位移和应力。

When the equivalent strain rate is relatively low, this influence can be neglected and the compression process can be considered as an isothermal process. While the equivalent strain rate is high, this influence is of importance and the compression process can be approximately considered as an adiabatic process.

当等效应变速率很小时，变形热效应对流动应力的影响可忽略不计，压缩过程可近似认为是等温过程；当等效应变速率较大时，变形热效应对流动应力的影响相当显著，压缩过程基本上成为绝热过程。

When the equivalent strain rate is relatively low, this influence can beneglected and the compression process can be considered as an isothermal process. While the equivalent strain rate is high, this influence is of importance and the compression process can be approximately considered as an adiabatic process.

当等效应变速率很小时，变形热效应对流动应力的影响可忽略不计，压缩过程可近似认为是等温过程；当等效应变速率较大时，变形热效应对流动应力的影响相当显著，压缩过程基本上成为绝热过程。

Moreover, the influences of all kinds of factors on adiabatic shear in high speed machining are analyzed.

该判据考虑了切削过程中第一变形区压应力的影响，克服了最大剪应力准则经验性强的不足。

According to the change regularity of deformation modulus, combining with the rock mass structure characteristic of region studied, using interpolation method, the deformation modulus of rock mass in 36# adit can be deduced. The average vertical deformation modulus of rock mass during 0-70 zone is 39Gpa, and the horizontal deformation modulus of rock mass is 51. 3GPa in nature stress state and 50.8GPa in engineering load state. The average vertical deformation modulus of rock mass during 70-140 zone is 32. 2Gpa, and the horizontal deformation modulus of rock mass is 41GPa in nature stress state and 42. 6GPa in engineering load state. It will be a good reference of engineering design and evaluation.

9根据节理岩体变形模量变化规律，结合研究区岩体的结构特点，采用插值的方法对36号平硐岩体进行变形模量的推测，得到0-70段岩体的平均铅直向的变形模量为39GPa，水平向的变形模量：天然应力状态下为51.3GPa，工程荷载作用下为50.8GPa；70-140段岩体的平均铅直向的变形模量为32.2GPa，平向的变形模量：天然应力状态下为41GPa，工程荷载作用下为42.6GPa，这为工程设计、评程设计、评价等提供了必要的参考。

Strength theories focus on the limit states of stress and strain in order to compare them with admissible stresses and strains.

强度理论主要研究应力和应变的极限状态，以便与容许的应力和应变进行比较。

Treating with coils as aeolotropy, this paper brings forward a set of mathematical mode for computing internal stress distribution of coil in the process of coil coiling, in which some factors are taken into account, such as the transverse distribution of shape, crown and curl tension of the strip, the friction between the strip and the reel, the friction between strips, and etc. Because the reel shrinkage and the inner circle of the strip losing radial restrain and circumferential restrain can induce interlayer slipping and the change of the whole coil compactedness , the assumption concerned ——"virtual reel" in the process of coil uncoiling is put forward, which takes the form of slow action to express the uncoiling process and, therefore clearly simulates the variation course of internal stress distribution of coil in the process of coil uncoiling.

考虑到带材板凸度、卷取张力的横向分布以及带材与卷筒之间、带材与带材之间的摩擦力等因素的影响，并将钢卷按各向异性体处理，提出一套计算卷取过程中钢卷内部应力分布的数学模型；同时考虑到卸卷过程中由于卷筒的收缩，钢卷内圈失去径向和周向约束而引起层间滑移及整个钢卷紧密程度发生变化，提出钢卷卸卷过程中有关"虚拟卷筒"假设，将卸卷过程以"慢动作"的形式表示出来，清楚地模拟出卸卷过程中钢卷内部应力分布的变化历程。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。