平均

Results:After d ealing with the wound which sealing time of acute wound was 1～3 weeks,average time was 2 weeks.Sealing time of chronic wound was 2～8 weeks,average time was 4 weeks.

结果：经该方法处理创面后创面愈合时间，急性创面1～3周，平均2周；慢性创面2～8周，平均4周。

In this paper, effects of atmospheric factors to Ka-Band earth-space links are analyzed, and the total fade distribution function is derived. With the scintillation prediction model, monthly averaged standard deviations and monthly percentage time averaged fade of scintillations for some of referential earth stations of our country are computed.

摘要本文分析了各气象因素对Ka-波段地空链路衰减特性的影响，得出了链路综合衰减分布函数，利用闪烁预测模型计算了全国各参考站点的闪烁月平均标准偏差和月百分比时间平均衰减值。

Mean tumor size was 1.2 cm (range, 0.8 - 1.6 cm), and mean time of RFA application was 13.8 minutes (range, 7 - 21 min). There was minimal or no discomfort, and no treatment-related complications other than minimal breast ecchymosis.

结果测得平均肿瘤大小为1.2公分（范围在0.8 - 1.6公分），平均电烧时间13.8分钟（范围在7 - 21分钟），患者感到不适的情形非常轻微，甚至根本没有不适的感觉，也未发生与治疗相关的任何并发症，即使是最轻微的乳房瘀血。

It has important theoretical significance and practical value for promoting level of environmental management and ecotype small town construction.

以海林市2005年实际发展状况为例，通过对比分析指标标准化法、最大隶属度和加权平均三种综合评价的优缺点，筛选与确定加权平均法为最优方法，并验证了本文提出的生态小城镇评价指标体系的可行性。

Its mean diameter is 3,475 kilometers (2,160 miles), its mass approximately one eightieth that of Earth, and its average period of revolution around Earth 29 days 12 hours 44 minutes calculated with respect to the sun.

它的平均直径为3，475公里2，160英里），它的质量约为地球的八十分之一，参照太阳，它围绕地球旋转的平均周期为29天12小时44分钟

Mean age was 64, and mean duration of time elapsed following stroke was 39 months.

这些病人平均年龄64岁，脑中风后平均39个月。

The average optical density that benefit measures organization of different period hemangioma and normal skin to organize Cyclin G1 and P53 expression with technology of computer image analysis and average and electropositive area.

利用计算机图像分析技术测量不同时期血管瘤组织和正常皮肤组织Cyclin G1和p53表达的平均光密度和平均阳性面积。

In order to install the electrothermic Board, silica gel used for blocking the release version of silica gel used for blocking the General selection of grass-roots level to 1-3 mm in thickness of the aluminum plate. Silica gel layer from the aluminum plate between the bond strength directly linked to silica gel used for blocking the version of the service life, if the silican layer from the aluminum plate between the bond strength is not high enough, the high temperature and high pressure easy to crack.

当然，在本质操纵洋上述几个参数的设定不是白云苍狗的，而给根据本质处事洋的需给举行拔取和设定，如铜、锌版不同，平均的烫印压辛、较矮的烫印温量和较缓的烫印速率会爆发更抱负的烫印成果，因为平均的烫印压辛使电化铝的黏结性更好，较矮的烫印温量使电化铝的光华量更矮，而较缓的烫印速率是为了适答较矮的烫印温量。

We can use the ellipsoidal model to calculate the relations of period derivation and braking index with average density.

而我们就可利用椭球模型来计算周期变率和制动系数同平均密度的关系；如果取平均密度约为2.2×10〓克/厘米〓，则周期变率约为5.4×10〓秒/秒，制动系数为-0.4。

Results: The prepared AmB-PBCA nanoparticle had a regular spherical or elliptic surface, with a mean diameter of (69.01±28.56) nm. The curve of standard AmB was linear within the range of 1.12-5.60μg/ml: D405=0.1634c+0.0066 (r=0.9993). The average recovery of AmB-PBCA-NP was 99.93%, showing the solution of AmB-PBCA-NP was stable within 12 h. The nanoparticles showed a sustained drug release in vitro within 24 h. The optimized recipe was: DextranT-70 stabilizer without sodium deoxycholate, with a mean encapsulation rate of 56.10% and a drug loading rate of 82%.

结果：制备的AmB-PBCA-NP外观呈圆或类圆形，平均粒径(69.01±28.56)nm，分散均匀；AmB标准品在1.12~5.60μg/ml范围内的线性回归方程为：D405=0.1634c+0.0066，r=0.9993，AmB-PBCA-NP的平均回收率为99.93%，其溶液在12h内稳定性较好；体外释放实验表明24h体外释放具有一定的缓释性；实验发现最优化的处方为稳定剂采用DextranT-70，且不加助溶剂脱氧胆酸钠，其包封率及载药量均比较高，分别为56.10%、82%。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。