工艺过程

The air cylinder jacket is an important spare part of the engine, it is usually produced by the flowing water line in batches, the precise of it"s production is very high.Generally specified equipments,tongs and cutting tools are adopted in it"s production,So in the course of the development of the air cylinder jackets CAPP, specified equipments, tongs and cutting tools must be considered.

气缸套是发动机的重要零件，其生产通常是采用流水线批量进行的，气缸套零件的加工精度高，工艺过程复杂，在生产过程中通常采用专用的设备，夹具和刀具，因此气缸套CAPP系统必须考虑生产过程中采用的设备、夹具和刀具。

This paper expounds the oxyacetylene flare overlaying welding technology of tungsten carbide rod made to be metal matrix carbide ceramal compound overlaying welding layers.

介绍碳化钨条氧乙炔火焰堆焊制备金属基碳化物陶瓷复合耐磨堆焊层的工艺方法，结合碳化钨条氧乙炔火焰堆焊工艺过程、堆焊层性能特点、泥沙磨损实验结果及显微组织形貌，分析讨论了热源性质对堆焊层性能的影响以及复合耐磨堆焊层的抗泥沙磨损特性。

A process for simultaneous purification of phosphatidyl choline and phosphatidyl ethanolamine by alumina column chromatography was developed, and the optimization of operating parameters was made.

研究了氧化铝柱层析同时分离纯化卵磷脂和脑磷脂的工艺过程，包括上样、洗脱工艺条件优化以及氧化铝再生等。

These concrete worksare the following:1, a new heterogonous SHS model had been proposed, which first included all the relativematerials characters, such as reactants particle sizes, changeable heat-conductivity and massdiffusion during SHS and so on, and its chemical reaction characters, initial combustion status.This new model made a more precise prediction about the SHS combustion way and itsTechnological characters possible.2, with the heterogonous SHS model, lots of combustion way had been imitated by changesystems relative factors and the rule of the combustion way change had also been studied,chemical reaction in these systems was controlled by a single mechanism.

在该模型中，首次将体系的微观不均匀特性、体系的基本物性及燃烧过程中的化学反应机理与整体燃烧动力学行为联系在一起，从而为更加准确地预测和控制SHS体系的燃烧行为，优化SHS的工艺过程奠定了理论基础。2、采用非均质燃烧模型，通过对相关参数的改变，模拟SHS燃烧过程中的各种燃烧行为，并研究了燃烧行为变化的规律。

The behaviors and factors effecting the diffusion of bath compositions in the coating layers,the characteristics of processing dynamics and technological processing,antifoging measures and mechanism,the factors of effecting granularity and sharpness and mechanism and the some facilities are discussed.

文章介绍并讨论了加工浴组分在照相材料涂层中的扩散行为和影响扩散的因素，过程动力学的特点，工艺过程特点(含显定合一过程特点及机理、防止灰雾的措施和机理、影响影像粒性和清晰度的因素及机理)和设备简况

According to chemical reaction in forming elastic grinding material this paper analyzes and discusses chemical balance in controlling the reaction and proposes prescription testing method and technology process in forming material.

基于弹性磨具材料生成过程的化学反应，分析讨论了控制反应过程的化学平衡问题，根据实验提出了弹性磨具材料配方试验的基本方法和生产工艺过程。

The poly-generation process,which combined the CFB combustion and coal pyrolysis is one of the effective coal utilization means in our country.This process is based on CFB,and combined combustion with pyrolysis.It make the combined produce of heat,electricity,gas and tar in a system become reality.This paper summarized the research situation about solid heat carrier coal pyrolysis based on CFB.

循环流化床燃烧/煤热解多联供技术是我国煤资源的有效利用方式之一，该工艺过程是以CFB为基础，集燃烧和热解工艺于一体，实现了热、电、气、油在一套系统中的联合生产，同时对基于CFB的固体热载体煤热解工艺的研究状况进行了综述。

Based on the overall analysis of whole process, compared with regular SBR treatment, under the same target of standard reached discharge, the technique has merits of low initial investment and operation cost. The quality of the effluent can meet the requirement of grade 1 in the meat-packing wastewater discharge standard GB13457-1992. Compared with other bio treatment processes. It has good stability and adapt ability.

在全面分析整个工艺过程的基础上，通过与常规的处理相比较，在同样达标排放的前提下，采用该工艺的工程初期投资和运行成本都较低，经该工艺处理后，外排出水水质能达到《肉类加工工业水污染物排放标准》(GB 13457-1992)的一级排放标准。

Mechanical manufacturing process, every change the shape, size production target, location and nature, make the finished product or process known as process of semi-finished products.

机械制造生产过程中，凡是改变生产对象的形状、尺寸、位置和性质等，使其成为成品或半成品的过程称为工艺过程。

Systemic works was carried out on the followed area, the surface modification of templates, the optimization of roll-press technique, the reason and simulation of crack formation in RPCs using FEM , the investigation of the two-step centrifuging technique.

在对工艺过程深入研究的基础上，通过有机泡沫体的表面处理、辊压工艺的优化、缺陷形成原因及有限元计算结果的分析、两次离心挂浆工艺及其影响因素等方面做了深入系统的研究，并为具有可控结构网眼多孔陶瓷的制备提供了一条崭新的途径。

With Death guitarist Schuldiner adopting vocal duties, the band made a major impact on the scene.

随着死亡的吉他手Schuldiner接受主唱的职务，乐队在现实中树立了重要的影响。

But he could still end up breakfasting on Swiss-government issue muesli because all six are accused of nicking around 45 million pounds they should have paid to FIFA.

不过他最后仍有可能沦为瑞士政府&议事餐桌&上的一道早餐，因为这所有六个人都被指控把本应支付给国际足联的大约4500万英镑骗了个精光。