工作分析

People are required to know and analyze the operating axes of rotary kiln in time in practice, in order to adjust and maintenance it in reason. So The Great Wall Aluminum Corporation of China bankrolled for studying the microcomputer real-time monitoring system of large-scale rotary kiln and commissioned Central South University to develop it.Based on analyzing and comparing the status quo of the monitoring system of rotary kiln, this paper brings forward a new method of monitoring the operating status of rotary kiln. It analyses the system-error and the configuration and demonstrate the feasibility in detail. In the design of hardware configuration it analyzes the principle and speciality of the tailor-made eddy current transducer and PCI-1713 analog input card and the multilevel supervisory network.

本论文首先在分析和比较同内外回转窑检测系统现状的基础上，首次提出了新的回转窑运行状态检测方法，并从系统误差及可行性角度进行了详细的分析和论证；其次，在监测系统硬件结构设计中，详细地分析了多级管理网络的实现，PCI-1713双缓冲区高速数据采集装置的原理、特点、工作过程，以及针对该系统恶劣的工作环境、特定性能要求而设计的特制电涡流传感器的原理、波形特性及性能特点，及为了减小非线性误差而采用计算机软件进行多段线性插补方法实现误差补偿；另外，在系统软件设计中，详细地分析了高速数据采样软件、智能信号处理软件、系统监测软件的实现，分析了采用模糊自适应滤波方法有效地滤除本系统恶劣环境下的各种干扰因素，并简要地介绍了系统分析软件的功能。

The mainly contents include: the research design of statistical survey, survey methods, the statistical sorting and analysis of information (contingency table, correlation measurement, inferential statistics, regression analysis, variance analysis, cluster analysis, factor analysis, principal component analysis), the composing of investigation report and the appliance of SPSS.

课程对社会统计和社会调查研究方法进行全面的介绍，要求学生牢固掌握社会统计和社会调查的基本研究方法，能熟练运用社会统计和社会调查的方法和技术从事社会研究工作，对社会统计学的概念和术语有一般程度的掌握，能应用SPSS软件进行社会统计和调查工作。本课程主要内容包括：统计调查的研究设计、资料的调查方法、资料的整理与统计分析方法（列联表、相关关系测度、推断统计、回归分析、方差分析、聚类分析、因子分析、主成分分析等）、撰写调查报告、SPSS应用等。

In this article two functional modes of the Fly-back Converter (Continuous Conduct Mode and Discontinuous Conduct Mode) are particularly analyzed, which include their characteristics, applications, the critical pattern of two functional modes is argued, both the exact boundary from the angle of circuit parameters is crystallized, at the same time, basic principle of PFC under the DCM mode is introduced, which settle theoretical basis for the subsequent design; by establishing the mathematic model of the converter, a further investigation of the configuration is made, qualitatively and quantitatively, analyzed to settle exactly theoretical basis for the subsequent emulation and the experimental parameter; from the angle of steady-state analysis, the transfer function of the system is deduced to establish dynamic small-signal state equation, emulating the system with the help of matlab, then according to the simulation result and the theory of PFC revise the system, lastly, we adopt the project which add a zero-pole compensator to the voltage loop, by this way, a satisfied system performance is gained and the PFC scheme is ensured successfully; finally, based on the previously-done work, we combining with the situation of specific design requirement, acquired the numerical value of each unit devices in this converter

详细分析了反激式变换器的两种工作状态，连续模式(Continuous Conduct Mode ，简称CCM)和断续模式(Discontinuous Conduct Mode，简称DCM)以及各自的特点、应用场合，论证了两种工作状态的临界模式，从电路参数的角度明确了二者的界限，同时还介绍了DCM模式下PFC的基本原理，为后面的设计奠定理论基础；通过对整个变换器系统建立准确的数学模型，对此变换器的电路结构做了进一步的研究，定性、定量地分析了变换器各部分的工作状态，为仿真和实验参数的确定以及电路参数的优化提供理论依据；从稳态分析的角度，为系统建立了动态小信号状态方程并推导出系统的传递函数，利用matlab对系统进行仿真，进而根据仿真结果以及PFC的相关理论对系统进行校正，采用在电压环加入零点—极点补偿器的设计方案，得到了满意的系统特性并且保证了PFC的顺利实现；最后，在前面所做工作的基础上，结合设计要求计算出此变换器系统中每个元器件的数值，利用Pspice对其进行了仿真、优化，然后根据仿真结果搭建了硬件电路。

Content abstract: The article from the job category, the investment originated, the operational mechanism three aspects to differentiate and to limit the public welfare and the commercial character two kind of heterogeneity geological work; Has analyzed the geology surveying work reform background, has been clear about the reform guiding principle; Has analyzed under the traditional system the geology surveying work existence malpractice, reviewed the former reform measure; Based on this, the major issue three aspects which from the organization, the operational mechanism and must solve establishes the land resources big investigation the new system, the new mechanism; Finally, the author believed that what the deepened commercial character geology work reform is most essential cultivates the geological minerals Investment company, namely, on the one hand expanded geology investigation investment origin, on the other hand the cultivation geology investigation's subject of investment, and must strive for stock going on the market positively, widely uses the social fund, the reform commercial character geology work operational mechanism.

内容摘要：文章从工作性质、投资来源、运行机制三个方面区分和界定了公益性和商业性两类不同性质的地质工作；分析了地质勘查工作改革的背景，明确了改革的指导思想；分析了传统体制下地质勘查工作存在的弊端，回顾了以往的改革措施；在此基础上，从机构、运行机制和必须解决的重大问题三个方面建立国土资源大调查的新体制、新机制；最后，作者认为，深化商业性地质工作改革最关键的是培育地质矿产投资公司，即，一方面扩大地质勘查的投资来源，另一方面培育地质勘查的投资主体，并要积极争取股份上市，广泛利用社会资金，改革商业性地质工作的运行机制。

Generally we used traditional analogism and the improvising method to design them. In this paper, the finite element analysis method is applied. Firstly, the static analysis of the device is carried out and the reaction forces at the joints are calculated.

本文基于有限元分析理论，首先研究装载机的工作装置的静力分析问题，根据装载机工作装置受力最大时铲斗所受的外力，以及装载机工作装置的位置分析，求得装载机工作装置中摇臂和连杆零件各铰接点处所受的力。

But in practical operating, overvoltage caused by reignition of the vacuum switching device frequently appears, and it result in damage of the capacitor bank or the switchgear itself. Ensuring the switchgear against reignition and installing a protective device are two main approaches to avoid the phenomenon. In this paper, a study on overvoltage caused by reignition due to capacitor bank switching with the vacuum switching device and its preventive measures are carried out. The main work which has been done and researches are as follows: 1. The producing mechanism of overvoltage and its influence factor are analyzed. It is pointed out that single-phase reignition is the main reason for damage of the switchgear and two-phase reignition is the main reason for damage of the capacitor bank,so overvoltage of single-phase reignition and two-phase reignition are the emphases of prevention. 2. Analysis of the special working condition of the operating switch for capacitor bank is carried out. It indicates that the vacuum switching device is difficult to realize no-reignition under this operation condition, so it is more practical to adopt protection devices. 3. Analyses of protection effect of RC and MOA and their shortages are carried out. It shows that the two methods can only restrain effectively overvoltage caused by single-phase reignition, and they cannot protect the capacitor bank when reignition of two-phase occurs. 4. The operation principle of G-R damping device is analyzed and discussed emphatically.

本文针对真空开关投切电容器组时因重燃而产生的过电压及其防治措施进行了研究，所开展的主要工作和研究结果如下： 1、对过电压的产生机理及其影响因素进行了分析，指出单相重燃是导致开关设备损坏的主要原因，而两相重燃则是导致电容器组损坏的主要原因，因此单相重燃和两相重燃过电压是防护的重点； 2、对电容器组操作开关的特殊运行条件进行了分析，指出在这种运行条件真空开关难于实现不重燃，因此采用保护装置更具有现实意义； 3、对RC与MOA的保护效果和存在的不足进行了分析，指出这两种方法均只能有效抑制单相重燃过电压，而不能在发生两相重燃时保护电容器组； 4、重点对G-R阻尼装置的工作原理进行了分析和讨论，指出该装置接入后线路中将会出现两种频率的高频振荡，而电容器组上的过电压是由这两种振荡共同决定的； 5、根据对上述两种振荡的分析指出存在一个最佳电阻值使得过电压最低，并提出了电容器组电压和最佳电阻值的近似求解方法； 6、使用电气暂态分析软件MATLAB对G-R装置的保护效果进行了仿真计算，证实该装置确实可以有效抑制重燃时的电容器组过电压； 7、根据仿真与近似计算结果的偏差提出了近似计算的修正方法，经过修正后的过电压计算结果与仿真结果吻合较好； 8、对G-R装置中放电装置G与阻尼电阻R的要求进行了分析，指出采用编织电阻和真空间隙可能是最佳选择。

With the support of a major research grant of Zhejiang Province (No. 001101027) and the Plan of Promoting Education of Excellence of Zhejiang University in the 21st Century, this dissertation is devoted to address the above problems and fabricate an L-band EDFA with low cost, high performance and technological innovation.First the mechanism of an erbium doped fiber amplifier is introduced. Various theoretical models based on classical rate propagation equations are summarized and compared for their applications. We use a modified numerical model based on the Giles model, which agrees with the experimental results well. This serves as the theoretical base for the whole thesis and will be used to optimize the characteristics of EDFAs. A novel method based on a map of noise figure and gain is proposed to analyze efficiently the dependence of the noise figure and gain for EDFAs on the EDF length and the pump power. The characteristics of various EDFAs are studied and compared.Secondly, some important parameters are introduced to describe the characteristics of EDFAs. The methods and the experimental setups for measuring the gain and noise figure of an EDFA are emphasized. We introduce how to measure the characteristics of each component of an EDFA, especially the gain and absorption coefficient of an erbium doped fiber.Thirdly, four types of simple and novel L-band EDFA structures with low noise, high gain and low gain ripple are proposed to satisfy the requirement of a DWDM system. They can be classified into two categories. In the first category, a single ASE pumping is served asa secondary pump. This category includes the following three types. Type: a new construction using a fiber Bragg grating in an unpumped EDF section at the input side. Type: a new structure of L-Band EDFA with two-stage pumps, which utilizes the forward ASE as a second pump.

本论文本着科技创新、服务于生产实践的精神，以设计价格低廉，性能优越、结构合理简单的L-band EDFA为目标，依托浙江省科技厅重大科学基金资助项目(001101027)和浙江大学振兴教育计划资助的全光网络的搭建—《光通信技术》课程实验建设项目，展开了如下工作：首先，介绍了掺铒光纤放大器的工作原理，归纳总结了基于速率方程基础的EDFA的各种理论模型，分析比较了各个模型的特点和适用场合，最终选择完善的Giles理论模型作为本论文分析设计EDFA的理论基础；针对实际实验条件提出了修正的EDFA模型的数值计算方法；创新地提出了增益—噪声系数全局分析法，直观有效地分析了EDFA的增益和噪声系数与掺铒光纤长度和泵浦功率的依赖关系，并对各种EDFA的性能作了全面的比较；第二，介绍了掺铒光纤放大器特性参数的定义与测量方法，重点介绍了噪声系数和增益系数的测量方法及实验装置；介绍了组成掺铒光纤放大器各组件的特性测量方法，重点介绍了测量掺铒光纤参数的方法和实验装置；第三，针对WDM系统对L-band EDFA谱平坦、低噪声、高增益的要求，我们创新地提出了四种不同的L-band EDFA结构，按设计思路可以分为两大类：一类是基于单抽运二级泵浦法，这一类包括在未泵浦掺铒光纤的输入端插入一根布拉格光纤光栅的两段L-band的EDFA的新结构；基于前向ASE光作为二级泵浦源推动下一级EDF工作的泵浦分配、两段级联L-band的EDFA的新结构；基于单根光纤光栅、泵浦分配、两段级联的EDFA；另一类则是基于同时应用前后向C-band ASE作二级泵浦源的双抽运法，如基于前后向ASE光作为二级泵浦源的三段级联L-band的EDFA的新结构。

A multi - agent corporate model including the firm owner , the manager and the auditor of the corporate is analyzed in the paper , the conclusions are : educing the optimum solution of model which could prevent the manager and the auditor becoming collusive or skulked ; clarifying the relationship between monitoring of the firm owner and working of the auditor , and illustrating the behavior combination of optimum solution ; further analyzing the relationship among monitoring degree , punishment of auditor and the auditor risk .

论文采用所有者经理人审计师多代理人模型为基础进行分析，主要成果是：得出能够防止共谋和不努力工作的模型最优解集合；通过因素分析阐明审计师工作努力程度与所有者监控力度之间的直接关系，以及审计合约最优解的行为策略组合及其制定顺序；引申分析所有者监控力度与审计风险、审计师惩罚力度之间的关系；成功的将模型从单一期间扩展到多期间情况，并且将审计师声誉等非现金收入形式的效用影响加入到模型当中；通过分析审计实务中的所有者行为特征说明所有者对审计师工作实施监控的必要性，以及实现该监控所需的条件。

A multi-agent corporate model including the firm owner, the manager and the auditor of the corporate is analyzed in the paper, the conclusions are:⑴educing the optimum solution of model which could prevent the manager and the auditor becoming collusive or skulked;⑵clarifying the relationship between monitoring of the firm owner and working of the auditor, and illustrating the behavior combination of optimum solution;⑶further analyzing the relationship among monitoring degree, punishment of auditor and the auditor risk. Adapting the model from a single term to serial terms, and adding the non-monetary utility of auditor--- reputation into the model;⑷describing behavior of the firm owner in reality and clarifying the necessity of monitoring by the owner and the environment improvements it needs.

论文采用所有者－经理人－审计师多代理人模型为基础进行分析，主要成果是：⑴得出能够防止共谋和不努力工作的模型最优解集合；⑵通过因素分析阐明审计师工作努力程度与所有者监控力度之间的直接关系，以及审计合约最优解的行为策略组合及其制定顺序；⑶引申分析所有者监控力度与审计风险、审计师惩罚力度之间的关系；成功的将模型从单一期间扩展到多期间情况，并且将审计师声誉等非现金收入形式的效用影响加入到模型当中；⑷通过分析审计实务中的所有者行为特征说明所有者对审计师工作实施监控的必要性，以及实现该监控所需的条件。

Through analyzing the work characteristic and the work mechanism of the interface in this research paper, bonded rebar technique is applied to the bonding treatment of the interface, the reformative method of enlarging sectional areas is proposed, and the work mechanism of the anchor bar in the interface is analyzed. The work mechanism of the reformative method of enlarging sectional areas and the interface mechanical performance have be more systematical analyzed and studied with the finite element numerical simulation method, the structural testing method, and combing project practice. Based on that, the suggestion formula of shear and tension bearing capacity for the old and new concrete is put forward.

本研究论文通过分析新旧混凝土界面的工作特点及工作机理，将化学植筋技术应用于新旧混凝土界面的粘结处理，提出改进的加大截面加固法，分析了锚筋在新旧混凝土界面上的工作机理；运用有限元数值模拟方法和结构试验方法，并结合工程实践，对改进的加大截面法的工作机理及界面受力性能进行了较为系统的研究分析，提出了新旧混凝土抗剪、抗拉承载能力的建议公式；根据研究结果，提出了改进加大截面法的设计原则和施工工法，并在工程应用中取得了良好的效果。

I will endeavour to find you some assistance.

我尽力帮你找人帮忙。

At first I only know bruck is the idol of American younglings, afterwards I returned back to Taiwan ,even in Beijing last year ,I saw her poster everywhere, I was so surprised at her charm.

起初我只晓得布鲁克雷德丝是美国少男少女崇拜的偶像，后来回台湾，甚至去年在北京，居然也四处看见她的海报，才惊讶她的魅力之大。