工件

Two-way from the X-Y table driven precision CNC workpiece completed X, 2 Y direction of the movement to X, Y, Z direction of the 3 Feed Movement ball screw, by AC servo motor drive.

由X-Y双向精密数控工作台带动工件完成X， Y两个方向的进给运动；X， Y， Z三个方向的进给运动均滚珠丝杠，并由交流伺服电机驱动。

This paper narrates the usage and maintenance of semi-automatic CO2 welding torch with feed push-wire,including the distance between nozzle and workpiece,wire feed cables of torch,using same size tip with wire,correct usage of soft wire feed tube,bending angle of gooseneck ,installation and uninstallation of gooseneck and inner soft wire feed tube.

对推丝式半自动CO2气体保护焊焊枪的使用与维护进行了详细的叙述，包括：喷嘴至工件间的距离大小，焊枪的送丝电缆，使用与焊丝尺寸一致的导电嘴，送丝软管的正确使用，鹅颈的旋转角度、装卸方法以及内送丝软管的装卸方法等。

The depth of cut is adjusted by the cross feed of the grinding wheel into the workpiece.

切削深度通过改变砂轮对工件的横向进给来进行调整。

The results show that, low feed rate of grinding wheel and high rotational speed of workpiece are helpful to obtain smaller envelope height.

结果显示，为得到较小的残留高度，应尽量保持低的砂轮进给速度，并且提高工件转速。

In the second part, the effects of grinding depth of cut, workpiece speed of feed, wear of wheel and grinding fluid on workpiece burn are reveal. And also, microhardness of ground surface layer as well as burn colour of surface are investigated experimentally.

第二部分通过大量的实验，探讨了磨削深度，工件进给速度，砂轮磨损和磨削液对磨削烧伤的作用机理，依据实验，本文提出了一些新的观点。

The grinding force experience formula is derived by means of experimental results. By the rotation dynamometer, the experiment with different speed of grinding wheel, different feed rate and working piece speed have been carried out.

利用旋转测力仪进行了不同砂轮转速、径向切削深度、以及工件转速对磨削力影响的测试实验。

Wire/workpiece short-circuit detection and display in manual wire feeding mode minimizes mechanical stresses on wire feed head supports.

焊丝和工件之间可以实现短路过渡，在手动送丝模块中能减少焊丝头支撑座的机械压力。

Through a series of experiments,the heat distortion curves of different position on such key parts of the grinder as feeding table,head box,grinding head are gained,and their influence factors are analyzed.

对深孔内圆磨削时磨削热对工件尺寸精度的影响进行了探讨，通过系列实验，获得了磨床进给滑板、床头箱、磨具等内圆磨床关键部件不同位置的热变形曲线，并对其影响因素进行了分析。

The multipolar scoop channel embedded mechanical finger manipulator through inserts a series of different outflow boundaries the mechanical finger to obtain the flexibility function, the different shape's work piece may use corresponding the finger to clamp separately takes uses the replacement entire jig.

求助：机械专业英语翻译，关于机器人的（1）多极凹槽性嵌入式机械手指机械手通过嵌入一系列不同外缘的机械手指来取得柔性化的功能，不同形状的工件可以分别使用对应的手指来夹取而不用更换整个夹具。

Influence of the workpiece s pre-hole diameters and passes on thick-wall cylinders hole flanging is investigated by experiment and numerical simulation.

采用实验研究和数值模拟的方法，分析了工件预加工孔径和孔型参数对厚壁筒体翻孔工艺的影响。

We have no common name for a mime of Sophron or Xenarchus and a Socratic Conversation; and we should still be without one even if the imitation in the two instances were in trimeters or elegiacs or some other kind of verse--though it is the way with people to tack on 'poet' to the name of a metre, and talk of elegiac-poets and epic-poets, thinking that they call them poets not by reason of the imitative nature of their work, but indiscriminately by reason of the metre they write in.

索夫农 、森那库斯和苏格拉底式的对话采用的模仿没有一个公共的名称；三音步诗、挽歌体或其他类型的诗的模仿也没有——人们把&诗人&这一名词和格律名称结合到一起，称之为挽歌体诗人或者史诗诗人，他们被称为诗人，似乎只是因为遵守格律写作，而非他们作品的模仿本质。

The relationship between communicative competence and grammar teaching should be that of the ends and the means.

交际能力和语法的关系应该是目标与途径的关系。