工件

So if both 5:5 pulldown and Smooth Motion are on, you will get the same set of artifacts as you do with 5:5 pulldown on and Smooth Motion off--the side of the ship is clean, but the prow still judders.

因此，如果双方5：5下拉和流畅的画面上，你会得到相同的工件设置为您5：5和平滑运动的下拉休学去做-船的一侧是干净的，但船头仍然judders。

The results show that after quenched and tempered with protective coating,no elements in the protective coating are found to permeate into the matrix,but the martensite laths in welded zone and heat affected zone are refined and the dispersion of carbides in these area is increased,the sizes of the dimples in these fracture are decreased.

通常情况下，D406A钢壳体在热处理中未采用保护气氛，造成调质后壳体表面脱碳严重，使壳体强度降低。为防止或减少调质处理过程脱碳带来的不利影响，可采用保护涂料或保护气氛热处理以及真空热处理等[2]，但对于大型工件，采用保护气氛或真空热处理需要大量的设备资金投入；而采用保护涂料投入较少。

For further enhances the numerical control engine laths the processing efficiency, the numerical control engine laths is clamping to the work piece in an engine laths attire then completes the multi-channel working procedure or the complete working procedure processing direction develops, therefore appeared each kind of type processing center engine laths, ike the turning center, the boring mill processing center, drills truncates center and so on.

为进一步提高数控机床的加工效率，数控机床正向着工件在一台机床一次装夹即可完成多道工序或全部工序加工的方向发展，因此出现了各种类型的加工中心机床，如车削中心、镗铣加工中心、钻削中心等等。

A kind of magnetic levitated wafer stage is designed. The wafer stage is compact, light, and precise.

设计了一种适用于极紫外光刻机的真空工件台系统，该系统具有体积小、质量轻、精度高等特点。

You will need a quartz rod to hold the object in place until it levitates, or while it is heating.

你得有个石英棒来在工件未悬浮之前托住它。

They can also be rather important depending on the intended end use for the work piece being machined.

它们也可以是相当重要的，这取决于被机械加工的工件的预期最终用途。

Compared with the numerical model, the analytical model is more propitious to studying relationship between process parameters and surface geometrical error.

通过研究这些因素，基于铣削力/铣削扭矩和瞬时未变形切屑厚度的关系，建立了一个考虑了铣削力/铣削扭矩的解析模型，用来预报在端铣情况下工件的表面几何误差。

Ultra-high strength 23Co 14Ni 12Cr3MoE steel was shot peened and the surface residual stress of shot-peened specimens was determined during rotating bending fatigue by X-ray diffraction method.The surface residual stress decreases greatly in the first 10 cycles and it is steady alter 100 cycles.

工件表面的残余应力，对其疲劳性能具有重要的影响，喷丸强化工艺主要利用的就是在表层产生一定数值大小的残余压应力以提高疲劳抗力，但喷丸残余压应力在疲劳过程中并不是稳定的，在一定外力或/和温度的单独或共同作用下，残余应力可发生松弛['一5]。

The distribution and variation of plastic zone in the joint were calculated and analyzed during inertia friction welding process. And the variation of deformation rate of plasticized material was also simulated.

计算并分析了惯性摩擦焊接过程中接头塑性区的分布、扩展规律及其与工件轴向缩短的关系，并计算了塑性区金属塑性变形速率的分布和变化情况。

Water jet machining is a special machining method using high pressure high speed water(pure water or water with additives) to impact the wor kpiece with the action of suspended abrasive in the water for cutting, pouching, crushing or surface material removal.

水射流加工是一项特种加工方法，采用高压高速水冲击工件，在水中悬浮磨粒的作用下，进行切割、穿孔、破碎或表面材料去除。

We have no common name for a mime of Sophron or Xenarchus and a Socratic Conversation; and we should still be without one even if the imitation in the two instances were in trimeters or elegiacs or some other kind of verse--though it is the way with people to tack on 'poet' to the name of a metre, and talk of elegiac-poets and epic-poets, thinking that they call them poets not by reason of the imitative nature of their work, but indiscriminately by reason of the metre they write in.

索夫农 、森那库斯和苏格拉底式的对话采用的模仿没有一个公共的名称；三音步诗、挽歌体或其他类型的诗的模仿也没有——人们把&诗人&这一名词和格律名称结合到一起，称之为挽歌体诗人或者史诗诗人，他们被称为诗人，似乎只是因为遵守格律写作，而非他们作品的模仿本质。

The relationship between communicative competence and grammar teaching should be that of the ends and the means.

交际能力和语法的关系应该是目标与途径的关系。