峰值

The peak power of the input signal in the NALM is about 8 mW.

实验中非线性放大环镜的输入信号峰值功率约为8 mW。

In the instantaneous voltage applied to the appliance exceeding 105 percent of the peak value of the specified test voltage.

施加测试电压时，应使得施加到器具的瞬态电压不超过规定测试电压峰值的105%。

Should say insusceptible, it is the discharge to this IP necessarily so, perhaps made peak value limitation in the light of this resource of fictitious lead plane, use independent IP to assure this, cannot come true at all.

要说不受影响，那么必然是对于此IP的流量，或者是针对此虚拟主机的资源作了峰值限制，采用独立IP来保证这一点，是根本无法实现的。

Its fully variable intake and exhaust valve timing achieves outstanding flexibility, delivering 90 percent of the engine's peak torque where it is most useful, between 1500 rpm and 6000 rpm.

完全的可变进气和排气气门正时达到出色的灵活性，提供百分之九十发动机的峰值扭矩，因为那里最有用的1500至6000转的转速。

Combining the experimental results and theoretical analysis, the following work has been accomplished.(1) Reasons of the decrease of interelectrode capacitance and the increase of discharge gap caused by the powder suspended in dielectric fluid are explained. And the mechanism that surface quality of workpiece improved by powder-mixed EDM is analyzed from this viewpoint.(2) The variation regularity of the percentage of silicon on the machined surface of workpiece has been summarized according to the experiment results when silicon powder was added into the working fluid. The entropy is introduced to explain the reasons for this variation regularity by thermodynamics.(3) The dimensional accuracy is greatly influenced by the overcut resulting from discharge gap and electrode wear in practice application. Empirical formulas for the overcut in EDM and powder-mixed EDM are established based on the experimental results using the ternary linear regressive method in this paper.(4) The influence of main factors on the machined surface characteristics has been evaluated based on the orthogonal experimental design method.

通过一系列普通电火花加工与混粉电火花加工的对比实验，运用工艺实验和理论分析相结合的方法，重点做了以下工作：(1)探讨了粉末颗粒导致极间电容减小、放电间隙增大的原因，并从这个角度解释了混粉电火花加工可以改善工件表面质量的机理；(2)以混合硅粉的电火花加工为例，实验得出峰值电流和脉冲宽度对加工表面层成分中硅元素含量的影响规律，并引入熵的概念从热力学的角度对硅元素含量变化的原因寻找了理论依据；(3)在实际加工中，由于粉末的加入使放电间隙变大，这使得混粉电火花加工的尺寸精度难以控制，本文利用三元线性回归的方法，在实验数据的基础上，建立了两种电火花加工过切量的计算公式；(4)将正交试验法应用于混粉电火花加工实验研究，并通过对实验指标极差的直观分析，得出各电参数对加工指标影响的敏感程度。

The intercalation ultraviolet absorption material begins combustion decomposition of interlamination negative ions at around 425 DEG C, and reaches peak temperature of exothermic peak thereof at the temperature of 478 DEG C, thus having strong thermal stability and being an excellent light and heat stabilizer.

该材料在约425℃左右才开始层间阴离子的燃烧分解，478℃达到放热峰的峰值温度，具有很强的热稳定性能，是一种优良的光热稳定剂。

The system was driven with menu to select and person-computer interlocutory way by LCD. The measured data and maxima data was displayed on real time.

采用液晶显示器，整个系统采用菜单提示选择和人机对话方式，实时显示实测值和峰值。

Measures and displays Peak Power, PRF, and Pulse spacing of Interrogator.??

测量和显示应答器的峰值功率，PRF和脉冲间隔。

Finally, an algorithm of reconstructing object contours by means of peak points and intersecting points is also proposed.

最后给出利用交点和峰值点直接重建物体轮廓线的算法。

The interventricular septum, mitral annulus and left ventricular posterior wall peak systolic velocity were also significantly different between the two groups.

室间隔、二尖瓣环及左室后壁收缩期峰值运动速度在OSAHS组与正常对照组之间比较差异有统计学意义。

Do you know, i need you to come back

你知道吗，我需要你回来

Yang yinshu、Wang xiangsheng、Li decang,The first discovery of haemaphysalis conicinna.

1〕 杨银书，王祥生，李德昌。安徽省首次发现嗜群血蜱。