屈服强度

The results indicate that the tensile strength,yield strength and the elongation reach 403.61MPa, 343.98MPa and 8.9%, respectively.

实验结果表明，复合材料的抗拉强度、屈服强度和延伸率分别达到了403.61MPa、343.98MPa和8.9%。

The deformation of conductive particles in pure metal connected by anisotropically conductive adhesives has been investigated using finite element analysis. The results indicate that the increment in stresses of the conductive particles begins at the contact area toward the boundary through the centers of conductive particles when the reduction in height increases. When stress is over the yield strength, the similar behavior was observed. So the deformation of conductive particles is not uniform, which means that the deformation of conductive particles is the same as the stress does.

采用有限元模拟分析了各向异性导电胶连接的纯金属导电颗粒的变形过程，研究结果表明，随着压下量的增加，导电颗粒的应力增加由接触面开始，经中心区域向导电颗粒的周边扩展，大于屈服强度的应力变化与此相似，因此导电颗粒的变形是不均匀的，即导电颗粒的变形由接触面开始，经中心区域向周边区域进行。

The results show that,In nomal institution,its yield strength,averager r -value and n value reach approximatly 150 Mpa,2.5 and 0.25,respectively.

实验结果表明，在正常情况下，热镀锌钢板其屈服强度在150Mpa左右，r，n 平均值分别为2.5和0.25。

Correspondently, the fatigue strength of B-free bainitic steel is higher than that of B-alloyed bainitic steel.

以此结果，提出了提高设计贝氏体钢的屈服强度的合金化途径与工艺途径的理论依据。

Twisting vibration of main transmission shaft during working, smaller dedendum comer R than the normal and lower material yield strength were the main reasons leading to main transmission shaft failure ahead.

主传动轴工作中存在扭振，齿根转角R偏小和材料屈服强度偏低是导致主传动轴提前失效的主要原因。

6Al10Ti5 bulk amorphous alloy with a diameter of 3 mm were annealed isothermally for 600 s at 673 K and 823 K, for 1500 s at 823 K, and for 3600 s at 723 K.

6Al10Ti5块体非晶在不同退火条件下的显微组织与力学性能，等温退火后可以得到尺寸约为 30—60nm金属间化合物相弥散分布在非晶基体上的混合结构、研究表明：块体非晶的压缩屈服强度为 1。

Combined with the observation of the metallograph and analysis of the change of chemical composition of alloys,we can draw the following conclusion:the addition of within the range of 40% once-used cobalt-chromium alloy to casting cobalt-chromium alloy wouldn't affect the quality of restorations,excessive addition of once-used alloy would damaged the microstructure and physical properties.

摘 要：通过比较不同比例的新旧钴铬合金铸造后的抗拉强度、屈服强度、延伸率、硬度等机械性能指标，并结合相应的金相观察及化学成份分析，得出结论：铸造钴铬合金中可加入不超过40％的仅铸造过一次的旧料而不影响合金的主要机械性能，超过这一比例，将影响修复体的质量。

The mechanical properties of coal filled polymer composites The mechanical properties of coal/PP composites were investigated, and the effects of coal rank, particle size, surface modification of coupling and alkylation were discussed. The results show that the anthracite and bituminous coal all can be used as filler of plastic after pretreatment of part devolatilization and surface modification; The modulus of composites increase with the content of coal filler; The coupling agent is of no effect for reinforcing the coal/PP composites, except that there are new oxygenous function group forming on the surface in the process of pulverizing; The F-C alkylation reinforce coal (under 10μm)/PP composites obviously.

4煤填充高分子复合材料力学性能超细煤粉填充聚丙烯复合材料力学性能的研究结果表明，烟煤和无烟煤经过脱除部分挥发分的预处理后，都可用于与塑料共混制备复合材料；偶联剂改性对低变质程度烟煤/聚丙烯复合材料的力学性能基本不起改善作用，而对于经气流超细粉碎后的小粒径高变质程度烟煤及无烟煤则有一定的增强作用；烷基化改性在煤表面接枝了烷基，使平均粒径小于10μm的煤/聚丙烯复合材料拉伸屈服强度普遍提高，煤填充高分子复合材料可在较高含煤量情况下维持良好的力学性能。

Tensile strength,yield strength and elongation of the alloys decrease and hardness increases as silico...

随Si量的增多，合金的抗拉强度、屈服强度和伸长率下降，硬度提高。

In current study, the laser shock processing technique of high energy and short pulse duration is adopted. The substructural transformation characteristics and mechanisms of 2Cr17Mn15Ni2N austenitic stainless steel, subjected to ultra-high strain-rate and impact stress in excess of dynamic yield strength of the target, are investigated by scanning electron microscope, X-ray diffraction and transmission electron microscope technology.

采用高能短脉宽激光冲击加载技术，利用扫描电子显微镜，X射线衍射和透射电子显微镜等手段，研究了在激光诱导的超高应变率和高于材料动态屈服强度冲击加载条件下，2Cr17Mn15Ni2N奥氏体不锈钢表面亚结构的转变特征和机制。

On the other hand, the more important thing is because the urban housing is a kind of heterogeneity products.

另一方面，更重要的是由于城市住房是一种异质性产品。

Climate histogram is the fall that collects place measure calm value, cent serves as cross axle for a few equal interval, the area that the frequency that the value appears according to place is accumulated and becomes will be determined inside each interval, discharge the graph that rise with post, also be called histogram.

气候直方图是将所收集的降水量测定值，分为几个相等的区间作为横轴，并将各区间内所测定值依所出现的次数累积而成的面积，用柱子排起来的图形，也叫做柱状图。