尾轴

This practical new-pattern power input axis 1 is assorted with furrow whole machine batholith 46 power fitting machine support 26 install rototiller axis 21 gear box 4,17 There are glide assorted umbrella gears 5, tooth border away-combine talon 7 and spring in axis .umbrella gears 5 and power input axis end of umbrella gears 11 mesh , the other end of axis with umbrella gears 42 mesh umbrella gears14 on rototiller axis 21, on axis 21 installs revovle furrow sword 23, on the shelf is tail wheel 29.tooth border away-combine talon 7 is driven by branch arm 35 on dial fork axis 34, branch arm is controlled by handle 38, connect part 39, control hold 36, it has orientation part .

本实用新型动力输入轴1与耕整机底盘46动力装置配合。机架26上装有旋耕轴21，齿轮箱4，17。轴1有滑动配合的伞齿轮5和牙镶离合爪7，有弹簧8。伞齿轮5与动力输出轴13端部的伞齿轮11啮合，轴13另一端有伞齿轮42与旋耕轴21上的伞齿轮14啮合，轴21上装有旋耕刀23，上有尾轮29。牙镶离合爪7由位于拨叉轴34上的支臂35驱动，支臂由手柄38，连接件39，操纵把36控制，有定位件45。

Methods. Electrical conductiity measurement was performed on 24 axial, circumferential, and radial annulus fibrosus specimens and 24 axial nucleus pulposus specimens from boine coccygeal discs.

研究方法：对24例牛尾椎椎间盘的纤维环标本进行了轴向、周围和放射向的导电性测试，对24例牛尾椎间盘髓核标本进行了轴向的导电性测试。

It's cost performance is extremely superior compared to ordinary single shaft or multi-shaft dovetail tenoner.

CSJ-500B数控燕尾榫机的性能价格比是其它普通单轴，多轴燕尾榫机无法比拟的

Slender mandrel connect with the spindle flange、end,spindle can drive mandrel to turn,at this time feed truck move to the position of reservation,rolling paper up to mandrel.

细长芯轴与主轴法兰、尾台法兰连接起来，主轴可带动芯轴旋转，此时送纸车移到预定位置，将纸卷到芯轴上。

Making the tail rotor 使尾桨 The tail rotor consists of a motor, tail blades, tail shaft holding tube and a blade holder.

使尾桨 该尾桨组成的汽车，尾气叶片，尾轴管控股和刀片持有人。

Sheer, B, ridge arc C, side top of the wall line D, the top line of the outer plate 4, the tail shaft exit ribs Contour Smoothing Setting out should meet the ...

、舷弧B、脊弧C、舷墙顶线D、外板顶线4、尾轴出口处肋骨型线放样时应满足的光顺。。。

Spraying of plastic on stern tube bearing.

尾轴管轴承塑料喷漆。

Spraying of plastic on stern tube bearing|n.

尾轴管轴承塑料喷涂

First you need the boring for the shaft, then install the stern tube into the stern frame, next fit the gun-metal or white-metal bush.

首先要镗孔，然后安装尾轴管，接下来装炮铜或白合金制的轴承套，也叫轴承。

The thrust coefficients and propulsive efficiency of a two-dimensional flexible fin with heaving and pitching motion were computed using FLUENT. The effect of different locations of the pitching axis on propulsive performance was examined using three deflexion modes which are respectively, modified Bose mode, cantilever beam with uniformly distributed load and cantilever beam with non-uniformly distributed load.

利用FLUENT软件数值计算了二维柔性鳍作升沉纵摇运动时的推力系数及推进效率，探讨了修正Bose变形方程、均匀载荷和非均匀载荷悬臂梁变形方程等三种柔性模式下纵摇轴位置对摆动鳍推进性能的影响，其中纵摇轴在尾缘处能够获得更大的推力，而最高的推进效率分别对应修正Bose模式下纵摇轴距首缘1/3弦长处和悬臂梁柔性变形模型下纵摇轴距首缘2/3弦长处。

Neither the killing of Mr Zarqawi nor any breakthrough on the political front will stop the insurgency and the fratricidal murders in their tracks.

在对危险的南部地区访问时，他斥责什叶派民兵领导人对中央集权的挑衅行为。

In fact,I've got him on the satellite mobile right now.

实际上 我们已接通卫星可视电话了