小孔

Cross cloth embroidered with the uniform is a woven fabric, cloth box on the form of numerous holes, each hole is the location of the pin.

布刺绣用的十字布是一种均匀编织的布料，布上的方格形成无数的孔，而每个小孔都是插针的位置。

The characteristics of pitting corrosion above breakdown potential E_b are studied for AISI 304 stainless steel in the solution of 1NH_2SO_4+0.5NNaCl at 25℃.

本文研究了AISI304不锈钢在25℃的1NH_2SO_4+0.5NNaCl溶液中，当电位正于击穿电位时发生小孔腐蚀的特征。

The mechanism of porous oxygen electrode to accelerate pitting corrosion of bronze ware has been put forwarded.

提出了加速青铜器小孔腐蚀的多孔氧电极机理。

This design is to dials forks the components the processing craft and the jig design, its components are the forging, has the volume to be small, components complex characteristic,Because the surface is easier than the hole to process, when formulation technological process, first the machined surface, then processes other take the surface as the datum,In which various working procedures jig all uses the unit clamp, special regarding processes the big end of hole, the trough and drills the capitellum hole incline eyelet in the working procedure, Chooses locate mode which two sells at the same time, and operates the simple manual clamp way clamp, its organization design is simple, the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。

This design is to dials forks the components the processing craft and the jig design its components are the forging has the volume to be small components complex characteristicBecause the surface is easier than the hole to process when formulation technological process first the machined surface then processes other take the surface as the datumIn which various working procedures jig all uses the unit clamp special regarding processes the big end of hole the trough and drills the capitellum hole incline eyelet in the working procedure Chooses locate mode which two sells at the same time and operates the simple manual clamp way clamp its organization design is simple the convenience also can satisfy the request.

此次设计是对拨叉零件的加工工艺和夹具设计，其零件为锻件，具有体积小，零件复杂的特点，由于面比孔易加工，在制定工艺规程时，就先加工面，再以面为基准来加工其它，其中各工序夹具都采用专用夹具，特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中，选一面两销的定位方式，并以操作简单的手动夹紧方式夹紧，其机构设计简单，方便且能满足要求。关键词拨叉，加工工艺，专用夹具，设计

Results There is egg cover before insect egg and is wrinkled increase part behind it. The nipples having cilium,sanken having or not cilium and little holes are distributed symmetrically around the oral sucker of cercariae. The nipples having cilium are discovered in the rest,which may have sense function.

结果 虫卵前端有卵盖、末端有皱褶增厚部分；尾蚴的口吸盘周围对称分布着有纤毛的乳突，有或无纤毛的凹陷及小孔；具纤毛的乳突在虫体的其余部分也有发现，可能起感觉器的作用。

We hope to show proof of principle, and to demonstrate efficient energy transfer, Colby said.

电子和光脉冲将穿过光子晶体中比微波加速结构狭窄10，000倍的小孔。

In order to improve the performance of aerostatic bearing and enhance the reliability of system, the chief works of this paper represents as follows: First, on the foundation of development and present research situation of internal and external aerostatic bearings, this paper summarizes the principle of aerostatic bearing, according to several assumptions of work conditions, two-dimensional Reynolds equation of isotherm compressible fluid is deduced.

为改善气体轴承的性能，提高气浮轴承转子系统的安全性、可靠性，本文进行了如下研究工作：首先，本文在综述了国内、外气体静压轴承的发展历史和研究现状的基础上对气体静压轴承基本原理进行了概述，根据小孔节流静压气浮轴承的工作状况，作了若干假设，在此基础上导出了描述气膜压力场的二维可压缩Reynolds方程。

The crampon can also be used for counterbalance or by hooking with the heel behind icicles or in holes in the ice .

冰爪有时用来做反平衡或用脚后跟钩在冰柱上，或者放进冰上的小孔内。

The crampon can also be used for counter balance or by hooking with the heel behind icicles or in holes in the ice.

冰爪有时用来做反平衡或用脚后跟钩在冰柱上，或者放进冰上的小孔内。

I didn't watch TV last night, because it .

昨晚我没有看电视，因为电视机坏了。

Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.

今年以来，在北京的很多小区里，电梯液晶电视被撤了下来。