将...分段

Cell Delineation is responsible for defining the cell boundaries at the originating endpoint (e.g., ATM cell switch or ATM workstation) in order that the receiving endpoint can reassemble (i.e., identify and recover) all cells associated with a data payload that has been segmented (i.e., cut up into ATM cells).

信元定界负责定义始发端（例如 ATM 小区交换机或 ATM 工作站）的小区边界，这样接收端可以将那些与已经分段的（也就是切割成数个 ATM 小区）数据有效载荷相关的所有小区重新聚集。

In this paper,several continuous variables are introduced to replace the discrete decision variable s,most importantly the pipe .

在数学模型中，引入连续变量代替离散的决策变量，这些连续变量是管道的"分段长度"，将混合整数非线性规划问题转化成连续的非线性规划问题。

Based on the current signal from the proceeding stage, the first orderΣ-Δmodulator designed could be simplified in the precondition of performance satisfaction, and it is good in accomplishing signal conversion and could be incorporated with the forestage bandgap circuit.

选择折线插值法进行非线性校正，通过硬件描述语言Verilog对体温计的占空比检测电路进行了设计，采用Matlab软件进行拟合仿真，获得了分段线性化输出方程，最后将信号转换为BCD码，在七段数码显示屏上输出。

The design of the device using NC Lathe CA6140 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with. from the I / O interface stepper pulse output signal to control the feed rate and itineraries; In order to maintain the function of cutting thread, to the outer end of spindle or other appropriate location loaded pulse generator; Lathe will be transformed into Tailstock manually controlled electric Tailstock.

本设计利用数控装置对CA6140普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

The design of the device using NC Lathe CA6240 control, part of the main transmission system using AC spindle motor and graded by the pulley driven spindle gearbox, through the inverter and gearbox to achieve sub; Feed System used by stepper motor driven ball screw slowdown after campaign vertical feed system through a gear after the ball screw drive, in the horizontal feed system through two gear-driven ball screw; Tool to automatically transfer tool carrier (4-position), thus achieving automatic tool change; by MCS-51 series 8051 data to be dealt with.

本设计利用数控装置对CA6240普通车床进行控制，主传动系统部分采用交流调频主轴电动机经带轮及分级齿轮变速箱驱动主轴，通过变频器和齿轮变速箱实现分段无级变速；进给系统采用步进电机通过减速后驱动滚珠丝杠运动，在纵向进给系统中通过一级齿轮减速后驱动滚珠丝杠，在横向进给系统中通过二级齿轮减速驱动滚珠丝杠；刀架改为自动转位刀架从而实现自动换刀；通过MCS-51系列8051单片机对数据进行计算处理，由I/O接口输出步进脉冲信号控制进给速度和行程；为了保持切削螺纹的功能，要在主轴外端或其它适当部位装上脉冲发生器；将车床的手动尾座改造成为可控电动尾座。

Main creative points of the thesis are as following:1. It is the first time to apply 2-D and 3-D turbulent model of the air-water two phases flow to the study on hydraulic properties of groyne. It makes description of the turbulent flow field to be possible precisely. This offers a more accurate method to determine the water surface in channel improvement.2. Based on the results of experiment and simulation for 3-D turbulent model of air-water two phases flow, a new formula to compute the height of damming is built.3. Based on the 2-D mode and the formula to compute the height of damming, the subdivision method of 2-D computation for water surface at upstream and downstream.

本文的创新工作主要是：首次将三维水气两相流紊流数学模型应用于丁坝水动力学特性研究，使丁坝附近流场和紊动场的精细描述成为可能，为航道整治中水面线确定提供了一个更为准确的方法；(2)基于水槽实验和三维水气两相流紊流数学模型数值模拟结果，建立了新的丁坝前奎水高度计算公式；(3)基于上述奎水高度计算公式和本文二维水面计算数学模型，首次提出了丁坝上下游二维水面分段计算方法。

"Tomorrow, we will begin to phase in the new system."

"明天，我们将开始分段采用新的系统。"

Chapter three (the methods of generating chaotic signal and its applications): In this chapter firstly the mechanism that a simple kinetic system, subsection linear map system, can generate chaotic phenomena is affirmed, the characteristics of correlation function of the chaotic signal generated by this system are simulated, on this basis a simple applicable method for generating chaotic signal is given; secondly some typical circuits generating chaotic signal are designed, also use operational amplifier to design a third -order autonomous circuit with chaotic dynamics. The basic mechanism and typical structures of chaos in the application of communication are introduced systematically and a simple method is provided for generating pseudo random code signal; At last Chaotic signal is applied into the analysis of system characteristic.

第三章(混沌信号产生方法及其应用)首先针对一类简单动力学系统——分段线性映射系统能够产生混沌现象的机理及由该系统所产生的混沌信号的自协方差函数特点进行了证明和计算机仿真，提出了软件产生混沌信号的一种实用方法；其次分析讨论了几种能够产生混沌信号的典型混沌电路，提出了用运算放大器与阻容元件实现三阶自治混沌电路的基本原理；概述了混沌在通信领域中应用的基本原理和典型结构，提出了产生伪随机码信号的一种简单方法；最后将混沌信号用于系统的特性分析中。

In order to reduce the computing time, a method to divide the load curve into sections and to form the related computation loads and ...

为减少计算时间，还提出了一种将负荷曲线分段并形成相应的计算负荷和持续时间的方法，该方法可明显地减少计算时间，而其所带来的误差不影响重构的最终结果

In order to enhance the training speed and the precision of neural networks, the daily load curve is divided and proper input and output variables are chose in each model.

为了提高神经网络的训练速度和精度，对每种不同的神经网络模型，将日负荷模型分段，选择出与预测日负荷相关的输入变量，比较得出最佳的输出变量。

In the United States, chronic alcoholism and hepatitis C are the most common ones.

在美国，慢性酒精中毒，肝炎是最常见的。

If you have any questions, you can contact me anytime.

如果有任何问题，你可以随时联系我。