导向轮

Application of antifriction bearing using in slide.

滚动轴承在导向轮中的应用。

The new unit adopts mechanical balance,uses load belt instead of wire line,replaces the crown wheel with double drums,and applies 12 guide wheels for improving load condition.

该新型抽油机采用机械平衡，用载荷胶带代替钢丝绳，将原来的天车轮换成双滚筒，并采用12个导向轮改善受力状况。

For ensuring the safe operation of ropeway ,the deviation value of passenger transport ropeway must be measured.

为了保证客运索道的安全运行，需要对客运索道导向轮偏移量进行测量。

Reel-to-reel Selective Planting Design:Guide wheel,sparger,masking belt and spot wheel plating tools are erected on SS franes which are imbedded in PPmaterial and installed in PP tank.

轮式点镀单元由不锈钢机架外表面包PP安装在PP柜内，机架上安装导向轮、喷头、遮蔽带与点镀轮模具等。

An automatic dipping production line machine equipment mainly comprises a liquid pool, a thermostated container, a curing oven, a heating cabinet, an air heating cabinet, a high pressure air heater., an air cooler, a column, a motor, a gearbox, a sprocket, a guiding wheel a supporting wheel, dual chains, a chain hanging scroll, a dedicated cradle, a vibratory pump, a dead lever, a wind plate and so on.

一种自动浸渍流水线设备，主要由液体池、恒温箱、固化箱、加热箱、空气加热箱、高压热风机、冷风机、立柱、电动机、变速机、链轮、导向轮、托轮、双链条、链条挂轴、专用挂篮、振动泵、固定杆、挡风板等构成，通电后，电动机驱动变速机使链条通过导向轮的定位导向，使待浸渍防潮液的物品的浸液、除余液、固化等工序自动连续完成，挡风板控制着热量的循环利用，具备优质高效、环保节能，是物品防潮浸渍的理想自动化流水线设备。

Fifthly, by adopt new matrix coordinate system means, found a tricycle WMR"s kinematic model, especially the investigation in the kinematically modeling of steered wheel and non-steered wheel. At the same time, the dynamic modeling of robot"s playing football motion, consummate mobile robots system.

第五，采用新型的矩阵坐标系方法，建立了三轮式机器人的动力学模型，尤其是在导向轮和非导向轮的动力学建模方面进行了深入的研究；同时，对机器人踢足球的运动进行动态建模，进一步完善了移动机器人体系。

One side of driving frame is fit with horizonal control roller,making stable running of entire machine during working.

主驱动侧装有水平导向轮，保证整机在运行过程中具有稳定的导向。

The cut-off valve with pilot valve without hand wheel, stem and lift nut inside will guide block and guide slot Butterfly Valves to guide sleeve, the disc-shaped disc to disc type bowl shape, and holes in the bottom of the flap valve to open, the valve cover of the original valve stem hole to hole diversion, because of increased pressure ring, ring, and the valve flap to class mortar, so that the flow passage separated the upper chamber cavity, external cavity, cavity, in the cavity and The external cavity increases with draft tube and stainless steel manual ball valve, flap valve in the cover plate and the center of the end of installing the spring, the upper flap valve install compression seal of the pressure ring, outside the cavity of the wall to open a Drainage holes.

带先导球阀的截止阀无手轮、阀杆和内升降螺母，将导向块与导向槽改为导向套，将盘形阀瓣改为类钵体形阀瓣，并在底部开阀瓣孔，电动蝶阀将阀盖原阀杆孔改为导流孔，因增加压环、密封圈和将阀瓣改为类钵体，使上通流腔分隔为上腔、外腔、内腔，在上腔与外腔的外部加设有导流管与不锈钢手动球阀，在盖板与阀瓣底的中心部加设弹簧，阀瓣上部加设压紧密封圈的压环，在外腔的壁上开有放水孔。

Steering wheel from one axle, bushing 2, 3 wheels, wheel frame 4, 5 bolt, with the 6 cylinder, outer cylinder 7, 8 screw shaft, nut 9, the bearings 10, felt ring 11 and handle 12, such as group into.

导向轮由轮轴1、衬套2、轮子3、轮架4、插销5、内筒体6、外筒体7、螺杆轴8、螺母9、轴承10、毡圈11和摇把12等组成。

And guarantee the space between 2 to 3 mm, at the same time, should guarantee the even space to prevent rubbing the safety brake, the adjustment method is that: relax the rolling wheel screw, adjust the direction of axle, after being adjusted, you should fix the screw.

调整要求保证侧轮和压轮与导轨间的间隙在单侧2-3mm之间，同时还要保证笼顶安全锁两边楔块与导轨架的间隙均匀，以防止正常运行时刮蹭安全楔块，调整方法是：松开导向轮紧固螺栓，调整导向轮中的偏心轴的方向，使间隙让到要求，调整完毕后必须轮紧固螺栓紧固。

Plunder melds and run with this jewel!

掠夺melds和运行与此宝石！

My dream is to be a crazy growing tree and extend at the edge between the city and the forest.

此刻，也许正是在通往天国的路上，我体验着这白色的晕旋。