对轴

The effect of tribology factors on bearing vibration is studied experimentally. AR model and WPT are used to processing the normal arid abnormal signals. The results are as follows:1. The vibration of ball bearings is caused by the tribology action of contact pairs of ball and ring races and has the essential of tribo-dynamics. Any factors affecting the tribology characteristics of contact pairs will affect vibration and noise of bearings consequently.2. Vibration characteristics of bearing keep almostly unchanged with the increasing of axial load expecting the increasing of nature frequencies. When radial load increasing with axial load unchanged, nature frequencies keep unchanged but some new vibration peaks appears in the spectrum.3. Vibration amplitudes are damped and nature frequency are enhanced with sufficient lubrication. Vibration and noise of bearings increase obviously and roar can happen and the contact surfaces scratch slightly under insufficient and unclean lubrication state. Bearing will be disabled in a few minutes without any lubrication.4. Bearing vibration is unstable under low speed. With the speed increasing, the vibration become stable and natural frequencies increase slightly but the amplitudes increase apparently.5. Bearing vibration can be excited only by some harmonics ofwaviness without lubrication and by all harmonics with lubrication based on the theoretical analysis.6. The nature frequencies of ball bearings decrease with the increasing sizes. When international clearance increasing, nature frequencies decrease in radial and increase in axial and angular and the amplitudes increase in radial and decrease in axial and angular. When the number of balls increasing, nature frequencies increase and amplitudes decrease. When the pitch diameter increasing, axial nature frequency increase and others nearly keep no change. When outer race groove curvature radius increasing, nature frequencies increase in radial and decrease in axial and angular and amplitudes keep no change in radial and increase in axial and angular. When inner race groove curvature radius increasing, nature frequencies decrease and amplitudes increase.7. The distortion in amplitude and frequency components of bearing vibration signals picked up by the present probe measurement method is founded and right conclusions cannot be achieved by the signals. When accelerometer is rigidly screwed with steel stud onto a flat outer surface of a ball bearing, vibration signal can be got without distortion and the reliability of research on bearing vibration is assured.8. AR model is suitable for large samples of bearing vibration signals, square root of length of samples can be used as the upper limitation of order determination and the FPE order selection criterion is effective. Many advantages of AR spectrum are founded over the classical based on FFT.9. Time-Frequency analysis is necessary for abnormal noise of ball bearings. WPT overcomes the principle shortcomings of STFT and proved to be a best tool to process the abnormal signals.

理论分析和试验研究表明： 1球轴承振动是钢球—滚道接触副中的各种摩擦学作用引起的，具有摩擦动力学的本质，任何对接触副的摩擦学特性有影响的因素都将对球轴承的振动和噪声特性产生影响； 2中心轴向载荷作用下，载荷增大使球轴承的固有振动频率升高，载荷越大同样的载荷增幅引起的频率升幅减小，足够大的中心轴向载荷作用下载荷的变化对球轴承振动的频率特性不会产生明显的影响； 3轴向和径向联合载荷作用下，径向载荷不大时球轴承振动的固有频率基本不变，但是可能引起变刚度激励的非线性振动，出现新的频峰，过大的径向载荷将使部分钢球脱离接触，使球轴承的振动和噪声呈现不稳定状态； 4润滑对球轴承的振动和噪声特性有重要的影响，良好的润滑对振动有明显的抑制作用，润滑不充分时，振动和噪声的水平会有明显增高，一定条件下还会激发接触副中的谐振，发出啸声，造成接触表面的伤害，无润滑干接触时，短时的运转就会损伤接触副表面，使振动和噪声迅速增大，并随时可能引发严重的磨损和卡滞失效；接触副润滑良好时，油膜的"刚化效应"使球轴承振动的固有频率有所提高，润滑剂中含有弥散性污浊时，振动的幅度总体升高，但弥散性污浊不会改变球轴承振动的频率特性；浙江大学博士学位论文：球轴承振动的研究 5低速时，球轴承振动的基本特征呈现不稳定状态，随着转速的提高，球轴承振动的频率特性趋于稳定，固有频率频峰升高； 6理论分析表明，干接触时钢球和滚道表面波纹度的某些谐波分量能激励球轴承的振动，振动的幅值与谐波幅值成正比，实际球轴承中钢球的分布不可能完全均匀，波纹度的激励作用会随时发生；润滑接触的分析表明，波纹度的任意谐波分量均能激励球轴承的振动； 7球轴承的几何和结构参数分析表明，球轴承尺寸越大，径向、轴向和角振动的固有频率越低；钢球中心圆直径增大，球轴承的径向和轴向振动的固有频率基本不变，角振动的固有频率有所上升，振动的幅频特性基本不变；径向游隙加大使球轴承的径向振动固有频率降低，轴向和角振动的固有频率有所升高，径向振动幅频特性的幅值升高，而轴向和角向降低；钢球的数量增多使球轴承振动的固有频率上升，幅频特性的幅值下降，径向振动的幅值下降最为明显；外圈沟曲率半径系数增大使球轴承径向振动的固有频率升高，轴向和角振动的固有频率降低，径向幅频特性基本不变，轴向和角向幅频特性幅值升高；内圈沟曲率半径系数增大使径向、轴向和角振动固有频率均下降，振动幅频特性的幅值均有升高； 8试验对比表明，传感器采用探针式安装时，由于探针接触副接触特性的影响，钡(量得到的球轴承振动信号有失真，采用专门设计和制作的试验球轴承，以固定式安装加速度计，首次测量得到了球轴承振动的真实信号，通过对振动信号的分析，验证了球轴承振动的理论模型； 9)基于时间序列分析的AR模型适用于大样本球轴承振动信号的分析，以样本长度的均方根值作定阶上界，FPE做判阶准则，给出的AR谱光滑，频率分辨率高，是球轴承振动分析的简便而可靠的手段； 10以时频域分析的小波包变换分析球轴承异音信号能够比较好地定位和聚焦异音发生的时间，时间间隔，频率范围，同样是球轴承振动分析的可靠的手段，可用作球轴承故障诊断技术。

Five novel torsion-mirror optical actuators including double-beam thickness differential structure with single torsional axis, double flexible folded-beam structure with single torsional axis, double-beam vertical torsion comb structure with single torsion axis, four-beam differential compound-micromirror structure with double torsional axis and the combined structure of the four basis forms above, are brought forward. All of these devices could be fabricated by the same silicon micromachining process we have developed. The deformation compensation design with local enhancement for the thin torsional beam which is the key structure of these devices is also put forward to improve the reliability. The three-dimension solid model and two-dimension reduced order model of the torsion-mirror optical actuator are established and then the numerical simulations for evaluating the device characteristics of the statics, dynamics, electrostatic field, mechanical and electrostatic coupling, fluid and solid coupling are carried out to optimize the structure design. Furthermore, three optical fibre clamping structures which could be integrated monolithicly are designed and analyzed to improve the optical coupling capability. 4. Three flexible process flows combined with bulk silicon micromachining and surface silicon micromachining are brought forward to fabricate these novel single-crystal silicon or polysilicon torsion-mirror optical actuators by using the same lithography masks for both SOI wafer and regular silicon wafer. A series of important process experiments are carried out to optimize the process parameters and the process flows. Some novel and typical process phenomena which occurred during the microfabrication are analyzed and then the corresponding solutions are put forward. 5. A MEMS dynamic testing system which exploit blur image synthetic technique, stroboscopic image matching technique, stroboscopic mirau microscopic interferometry technique and microscopic laser dopper vibrometer technique is set up to measure three-dimension and six-freedom micro motions of any MEMS devices with nanometer resolution.

在对硅微机械扭转镜光致动器的光机电特性系统地理论研究的基础上提出了硅微机械扭转镜光致动器的结构设计准则。3、提出了单轴双梁厚度差分结构、单轴双柔性折叠梁结构、单轴双梁垂直扭转梳齿结构、双轴四梁差动复合微镜结构以及以上四种基本结构组合后的衍生结构等五种工艺加工技术兼容的新型的硅微机械扭转镜光致动器，对器件关键结构薄厚度、高耐疲劳扭转梁进行了局部加强的变形补偿设计，建立了器件的三维实体模型以及两维降阶模型，对提出的新结构硅微机械扭转镜光致动器进行了系统的静力学、动力学、静电场、力电耦合和流体固体耦合的建模仿真与优化设计，同时设计并分析了三种可实现单芯片集成的弹性光纤定位夹紧结构。4、提出了组合体硅微加工技术与表面硅微加工技术、兼容同一套光刻版图、可分别基于SOI 晶片和普通Si 晶片、适应于制造提出的各种新结构单晶硅和多晶硅硅微机械扭转镜光致动器的三套柔性加工工艺流程，开展了一系列重要工艺步骤的单项工艺试验，对工艺流程与工艺参数进行了优化，针对加工过程中出现的具有普遍意义的典型工艺问题进行了讨论和分析，并提出了解决方法。5、创新性地将模糊图像合成技术、频闪图像匹配技术、频闪Mirau 显微干涉技术与显微激光多普勒测振技术有机结合，建立起了一套周期运动测量与瞬态运动测量相结合、单点运动测量与全视场运动测量相结合、满足不同MEMS 器件各种动态测试要求的集成的MEMS 三维六自由度微运动精密测量系统。

III Investigations of ferromagnetic alloy films by XMCD1. By using XMCD and SQUID magnetometry, the spin and orbital moments of Fe and Co in the Co_(0.9)Fe_(0.1)(50nm) are studied. Compared with single-element film, the spin moment of Co remains constant while that of Fe reduced from 1.98 to 1.63μB. The contributions of different elements in the film is, m_ : m_ - 10.5 : 89.5. The average magnetic moment (1.90μB) determined by XMCD is in agreement with that (1.82μB) obtained from SQUID measurements. Utilizing XMCD spectra in-plane element-dependent magnetic anisotropy in Co_(0.9)Fe_(0.1) films has been investigated. Apart from known field-induced easy axis during film growth, a soft axis perpendicular to it was observed, and hard axes are 66° away from the easy axis.

利用XMCD谱研究了50nm Co_(0.9)Fe_(0.1)薄膜，结果发现：样品中Fe、Co元素对磁化强度的贡献比为10.5∶89.5；由XMCD获得的合金平均原子磁矩1.90μ_B与用SQUID磁强计得到的合金平均原子磁矩1.82μ_B基本相符；对Co_(0.9)Fe_(0.1)薄膜面内元素分辨的磁各向异性的研究发现，除了在生长的磁诱导方向存在易磁化轴外，与该轴垂直的方向还存在一个类似易轴的软磁化轴；面内的两个难磁化轴与易磁化轴取向大约成66°夹角，构成面内双轴磁各向异性，并根据XMCD结果对面内双轴形成的原因进行了分(来源：Ad2BC82论文网www.abclunwen.com)析。2。

Motibity changed by gear-box in direction and rotate speed is transferred to the blade axis on the right side to drive the blade axis. blade axis'parameter, blade assembling frame and blade assembling means are ascertained. The load and movement of the blade axis are analyzed. And the best blade rotate speed is ascertained. According to the request of no-tillage soil, the appropriate furrow openers are chosen. They are staggered and assembled in two rows .According to the sliding cutting request, the crucial parts of the anti-blocking——the sliding cutting blade, its edge curve is analyzed and designed in principle. The academic curve function is gotten. Combined with working practice and technics request, the blade's figuration parameter is designed, 65Mn is chosen as the material for blades. The working load is analyzed. And the intension of the sliding cutting is analyzed and checked with ANSYS software. At last, the spring rack of the suppress wheal is analyzed in principle. The theory and parameter of designing the spring rack of the suppress wheal. Experiment indicated that the anti-blocking capability of this anti-blocking equipment was excellent.

设计出适合此防堵装置的动力传输方案，动力经变速箱变向变速后从右侧传给刀轴，驱使刀片切割秸秆；确定出了刀轴的参数、刀片的安装结构和安装方法，对刀轴的受力和运动进行了分析，确定出了刀轴最佳转速；根据免耕地的要求，选择恰当的开沟器，并采用双排错位安装的办法，避免了"瓶颈"现象的发生；根据滑切的要求对此防堵装置的关键部件——滑切刀片的刃口曲线进行了理论分析和设计，得到了刀刃的理论曲线方程；结合生产实践及工艺要求，设计出刀片的外形参数，选择65Mn作为刀片的材料；分析和计算了刀片在工作中承受的载荷，运用ANSYS 软件对滑切刀片的强度进行了分析校核；最后对镇压轮的弹簧支架结构进行了理论分析，提出了设计镇压轮弹簧支架的理论和参数依据。

A APDL program is developed for analyzing the contact stress of journal bearing pair of roller cone bit. The 25 contact stress cases of different clearance fit(including clearance of large bearing is bigger, equal to and smaller than that of small bearing) journal bearing pair of the 8 1/2XXX roller cone bit are analyzed. The result is that the maximum contact stress is less when the clearance of large journal bearing pair is smaller than or equal to that of small journal bearing pair.

用参数化设计语言APDL编制了牙轮钻头滑动轴承的ANSYS接触有限元分析程序，根据钻头制造厂方提供的某8 1/2的轴承配合间隙尺寸，分三种不同的间隙配合（大轴间隙大于小轴间隙、大轴间隙等于小轴间隙、大轴间隙小于小轴间隙），共25种情况，对轴承的表面的接触应力进行了分析，得出：大轴间隙小于等于小轴间隙时最大应力比较小。

The printed UWB antenna is comprised of a planar monopole radiator and the ground plane which are connected to a coaxial cable to launch RF signals. This kind of ground and antenna system is essentially an unbalanced design, where electric currents are distributed on both radiator and ground plane, and then leakage to the outer conductor of the feeding cable. The impedance matching and radiation pattern will be influenced in the low band, which are our focus. Finally, some techniques will be proposed to reduce the cable effect on the antenna performance.

进行超宽频天线量测时，吾人会利用同轴缆线连接到网路分析仪，这时的同轴缆线不只是扮演一个传输讯号的工具而已，由於单极天线的不平衡结构，对低频而言，接地回流电流会泄漏到同轴接地的导体外部，造成同轴缆线也是一个辐射体，影响到天线低频时的阻抗匹配与辐射特性，因此本论文将探讨同轴缆线对於天线一些参数的影响，并研究提出解决的办法。

Based on the critical approach, a model for multiaxial fatigue life prediction was established by combining maximum shear strain and normal strain on the critical plane, and the effect of stress state under the multiaxial cyclic loading condition on the fatigue life was taken into account.

通过对薄壁圆管和缺口试样的高温多轴疲劳寿命特性分析，基于临界面方法提出了一个的多轴疲劳寿命预测模型，在考虑临界面上最大剪应变和正应变对多轴疲劳损伤贡献的同时，还引入了应力状态对多轴疲劳寿命的影响因素。

Stern tube may be welded in between shaft boss and aft peak bulkhead.

可以对轴毂和艉尖舱壁之间的尾管进行焊接。

The statistic analysis is made for the vehicle type,bearings and axle temperature of vehicles with application of the sample data of predicting hot box.

利用预报热轴的样本数据对车辆的车型、轴承、轴温进行了统计分析，提出为了减少多报和误报，应区别对待C64系列、C80型等车辆和2位轴、4位轴的热轴判别数学模型，对能区分的C64系列、C80型等装配SKF轴承的车辆应建立单独的热轴判别数学模型，以提高热轴判别的准确率和兑现率。

And the H∞ control in the control design of magnetic bearing was applied.

采用了基于H∞控制系统的优化设计思想，在对轴向磁轴承H∞控制进行分析的基础上将H∞控制应用于磁轴承的控制器设计中。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐