对比系数

Finally it analyzes the feasibility that using hydromechanics to analyze traffic flow by contrasting various characters between traffic flow and fluid flow. It analyzes influence of road alignment to basic expressway segment capacity by hydromechanics, and obtains viscous resistance and viscous movement differential equation when the vehicle drives on circular curve segment of expressway. And it infers that viscous resistance is correlated with sideway force coefficient, slope of crown and radius of circular curve. Radius of circular curve, sideway force coefficient and slope of crown are bigger, viscous resistance is smaller, the influence to capacity is smaller when the vehicle is running on nearside lane of circular curve; but radius of circular curve and sideway force coefficient are bigger, slope of crown is smaller, viscous resistance is smaller, the influence to capacity is smaller when the vehicle is running on fast lane of circular curve.

最后通过对比交通流与流体流的相似性，运用流体力学分析了道路线形对快速路基本路段通行能力的影响，求出了车辆在曲线路段的粘性阻力，建立了车辆在曲线路段的粘性运动微分方程，并由此推知，粘性阻力与横向力系数、路拱横坡度和圆曲线半径都有关系，当车辆在圆曲线外侧车道上行驶时，圆曲线半径、横向力系数和路拱横坡度越大，粘性阻力就越小，对道路的通行能力影响就越小；而当车辆在圆曲线内侧车道上行驶时，圆曲线半径和横向力系数越大，路拱横坡度越小，粘性阻力就越小，对道路的通行能力影响就越小。

A new calculation model is established using the simulating curves presented by Standing and Katz. The coefficients of the correlation are determined by fitting to the data of Standing and Katz Z-factor chart. The results of the two models are compared, the conclusion can be drawn that the error of LXF model is smaller than that of DAK model.

利用两种模型对不同拟对比温度和拟对比压力组合条件下的天然气偏差系数进行了拟合计算，与理论图版值的误差对比显示，在高温高压条件下LXF模型的拟合结果更优，特别是随着拟对比压力的增加，LXF模型的误差不断减小，因此，该模型更适用于高压和超高压条件下天然气偏差系数的工程计算。

We also believe that we can compare the enterprises in the same industry with Matrix of Direct Input Coefficients and Matrix of Cumulative Input Coefficients. In our practical analysis and demonstration, we analyze the main expenses of the enterprises linking with their value-added.

同时，发现可以用投入产出表中的直接消耗系数表和完全消耗系数表对处于同一行业的企业作对比分析，可以将企业的相关费用与企业创造的增加值结合起来作对比分析。

First by testing the practical multilayer insulation in a cryogenic tanker, which is the carilometer in my paper,some affecting factors on multilayer insulation are analysed, then by using the low-temperature and vacuum environment caused by multilayer insulation, the effective thermal conductivity of multiple fiber paper with 5 layers is tested.Through Newton interativemethod,an empirical formula is deduced to computer the thermal conductivity of fiber paper,The errors between experimental thermal conductivity and the calculated conductivity by empirical formula are below10%,so the formula of fiber conductivity can be applied to practical enginnering.

为探索改善工程应用中高真空多层绝热层绝热性能的方法，本文实验研究中首先测量了包扎在实际低温储罐上不同结构的高真空多层绝热层的绝热性能，并分析了环境温度、环境压力，层数、不同隔热材料的组合等因素对工程应用中的高真空多层材料绝热性能的影响；然后利用多层绝热层中的低温真空环境测量5层干法纸在不同温度区间内的表观导热系数，在有限实验数据的基础上用牛顿迭代数值拟和出计算5层干法纸表观导热系数的经验公式，对比经验公式计算值和实验测量值，发现二者的误差在10%以内，因此在工程应用中可用本文的经验公式计算干法纸在低温下的导热系数。

Based on it, the research content of this dissertation has been determined. Tuan Shan River Bridge is selected as an example and APDL is used to analyze the elastic properties. After calculating the internal force influence surface of assembly skew hollow slab bridge, the internal force-controlling section is attained; the transverse distribution of internal force is studied and the transverse distribution coefficient is parametric analyzed. Based on the results, relation formula of transverse distribution coefficient between skew and perpendicular bridges are fitted. Practical calculation method for the internal force calculation of assembly skew hollow slab bridge is offered. Some conclusions are drawn from comparing and analysing the internal force, bearing reaction and deformation of both assembly and monolithic skew slab bridges.

本文对装配式斜交空心板桥的发展现状进行了综述，从此出发，确定了本文的研究内容，以团山河大桥为工程背景，采用ANSYS 提供的参数化语言APDL，对装配式斜交空心板桥弹性特性进行全面分析，计算了装配式斜交空心板桥的内力影响面，得到内力控制截面；同时计算了内力的横向分布影响线和横向分布系数，并对内力横向分布系数进行了参数分析；基于参数分析的结果，拟合了装配式斜交空心板桥与对应正交桥内力横向分布系数的关系式，为装配式斜交空心板桥的内力计算提供了实用计算方法；对比分析了装配式斜板桥与整体式斜板桥的内力、支座反力以及变形特点，得出了一些有益结论。

This article analyses the application conditions of freezing method, current research status and the problems in this field. It points that it's necessary to study deep freezing temperature field deeply and discusses the factors which influence the freezing wall such as soil's nature, moisture content, geological conditions, etc. It introduces the theory, process of freezing method, the distribution of temperature field of freezing method and key thermotics parameters influencing freezing temperature field. It simplifies the deep freezing temperature field model. Through ANSYS, this article founds the deep freezing temperature field model, and simulates the field on vary heat conductivities. It analyzes the results of ANSYS simulation, gains the theoretical value of thermometric holes which is needed by back-analysis. Using the simulation temperature and actual value, it gets the equivalent heat conductivity. Then it solves the deep freezing temperature field by the equivalent value, simulates the freezing wall development process and temperature change curve. Against the actual project, the results are favorable.

文中分析了冻结法施工的应用条件，目前对冻结法施工的研究现状和在此领域内存在的问题，指出了对深土冻结温度场进行深入研究分析的必要性；对影响冻结壁形成发展的因素如冻土土性、含水量、地质条件及施工方法等因素进行了论述；对冻结法施工的原理、过程，冻结法温度场的分布情况，影响冻结温度场分布的主要热学参数进行了综述；对深土冻土温度场模型进行了合理的简化，通过ANSYS大型有限元分析软件，建立了深土冻结温度场的模型，对不同导热系数情况下的深土冻结温度场进行了模拟；对ANSYS的模拟结果进行了定性的分析，通过对ANSYS结果的后处理取得了反分析时需要用到的测温孔理论温度值；经过对测温孔模拟温度值和实测温度值的分析，得到了冻结温度场的等效导热系数；使用等效导热系数对深土冻结温度场进行了求解，模拟了冻结壁发展情况和温度场中的温度变化曲线，用所得结果对比工程实际情况，取得了较好的效果。

This article analyses the application conditions of freezing method, current research status and the problems in thisiold. It, points that it" s necessary to study deep freezing temperature field deeply and discusses the factors which influence the freezing wall such as soil" s nature, moisture content, geological conditions, etc. It introduces the theory, process of freezing method, the distribution of temperature field of freezing method and key thermotics parameters influencing freezing temperature field, it simplifies the deep freezing temperature field model. Through ANSYS, this article founds the deep freezing temperature field model, and simulates the field on vary heat conductivities. It analyzes the results of ANSYS simulation, gains the theoretical value of thermometric holes which is needed by back analysis. Using the simulation temperature and actual value, it gets the equivalent heat conductivity. Then it solves the deep freezing temperature field by the equivalent value, simulates the freezing wall development process and temperature change curve. Against the actual project, the results are favorable.

文中分析了冻结法施工的应用条件，目前对冻结法施工的研究现状和在此领域内存在的问题，指出了对深土冻结温度场进行深入研究分析的必要性；对影响冻结壁形成发展的因素如冻土土性、含水量、地质条件及施工方法等因素进行了论述；对冻结法施工的原理、过程，冻结法温度场的分布情况，影响冻结温度场分布的主要热学参数进行了综述；对深土冻土温度场模型进行了合理的简化，通过ANSYS大型有限元分析软件，建立了深土冻结温度场的模型，对不同导热系数情况下的深土冻结温度场进行了模拟；对ANSYS的模拟结果进行了定性的分析，通过对ANSYS结果的后处理取得了反分析时需要用到的测温孔理论温度值；经过对测温孔模拟温度值和实测温度值的分析，得到了冻结温度场的等效导热系数；使用等效导热系数对深土冻结温度场进行了求解，模拟了冻结壁发展情况和温度场中的温度变化曲线，用所得结果对比工程实际情况，取得了较好的效果。

A method using a tiny thermistor as heat transfer model was developed to measure thermophysical properties (thermal conductivity and thermal diffusivity) of three standand samples(ethanol, ethylene alcohol, solution of calcium chloride). Results showed that there was no significant difference between measurement and recommendation; results of thermal conductivity from thermistor method and heat probe method for carrot and potato samples showed no significant difference; results of thermal diffusivity between thermistor method and calculation for carrot and potato samples showed no significant difference.

在分析微珠状热敏电阻传热模型的基础上，在室温对标准样品（乙二醇、乙醇、氯化钙的水溶液）的热物性进行测定，结果显示，导热系数及热扩散系数的测量值与推荐值之间无显著性差异（p＞0.05）；热敏电阻法与热探针法对比测定胡萝卜及马铃薯两种农产品的导热系数，结果显示两种方法之间无显著性差异（p＞0.05）；热敏电阻法与常规计算对比测定胡萝卜及马铃薯两种农产品的热扩散系数，结果显示两种方法之间无显著性差异（p＞0.05）。

Analyzing the changing rule of reaction time under road lighting level of different lighting sources can ascertain the luminance contrast coefficients of different lighting sources to high pressure sodium lamp, then appropriate lighting source can be selected based on these coefficients during road lighting designing, road lighting could achieve the aim of safely, quickly, cozily run and energy saving.

分析不同光源在道路照明水平下的反应时间变化规律，可以确定不同光源对高压钠灯的亮度对比系数。在进行道路照明设计时，就能选择合适的照明光源，使道路照明进一步达到安全、快速、舒适和节能的目的。

Then the waveband was divided into two parts to develop calibration model using partial least square method for soluble solids content to remove the effect of the skin and the results indicated that the measurement results was not be enhanced. However, the difference of calibration results in the wavelength of 650-950nm with the r of 0.949, the RMSEC of 0.292 for intact watermelon and with the r of 0.973 and the RMSEC of 0.214 for skin-peeled watermelon indicated that the influence of skin is not very serious and the intact watermelon spectra also can get satisfied calibration result. 5. Vis/NIR spectroscopy nondestructive detection needs high-energy light source, so differences of diffuse transmittance spectra with different light intensity (600W, 1000W) were detected and effects of light intensity on spectra and calibration results were compared.

针对西瓜果皮较厚的特点，对去皮西瓜与带皮西瓜进行对比试验研究，发现果皮对光谱的影响主要集中在可见光部分(650-750nm)，对可溶性固形物含量采用偏最小二乘法进行分段建模并没有有效消除果皮的影响，对比研究去皮西瓜与完整西瓜光谱在650-950nm范围内的建模结果，完整西瓜二阶微分光谱校正模型相关系数r为0.949，RMSEC为0.292，去皮西瓜校正模型相关系数r为0.973，RMSEC为0.214，果皮对建模结果的影响并不严重，完整西瓜的建模结果可以满足检测要求； 5。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。