对应点

Since the distance between these two points is 182 units, the fundamental frequency is fs/(182/5)= 16000/(182/5)= 439.56 Hz, which is equal to 68.9827 semitones.

在上述范例中，上图红线的位置代表音框的位置，下图即是 256 点的音框，其中红线部分包含了 5 个基本周期，总共占掉了 182 单位点，因此对应的基本频率是 fs/(182/5)= 16000/(182/5)= 439.56 Hz，相当於 68.9827 半音，其中由基本频率至半音的转换公式如下

When the swirl variable device is part-opened, because swirl has some effect on the second injection, second injection timing has distinctly effect on fuel consumption, and the fuel consumption change fluctuantly with twice injection timing. When the tumble variable device is adopted, second injection timing also has effect on fuel consumption, but there is only one point that the fuel consumption is lowest. When the load is bigger, the second injection point where the fuel consumption is lowest is earlier than the smaller load.

在可变涡流结构中，当阀片处于非全开状态时，由于涡流运动对二次喷油的作用，二次喷油正时对发动机的比油耗存在明显影响，发动机比油耗随喷油正时改变呈较明显的波动状；在可变滚流结构中，二次喷油正时对发动机比油耗同样存在影响，但最低油耗点只有一个，当负荷较大时，最低比油耗所对应的喷油正时要更早一些。

Experiment results show that this method can find the correct feature point pairs under transformation and local distortion.

实验结果表明，该方法可以在变换与局部变形存在的情况下，正确判定两幅指纹之间对应的特征点。

The invention performs pseudo bit error rate statistic by utilizing the message of multi sampling points in each modulation symbol of discretization system, and again performs one-to-one mapping by utilizing corresponding relation between the pseudo bit error rate and the signal-to-noise ratio, thereby obtaining signal-to-noise ratio estimation value.

本发明利用了离散系统每个调制符号中多个采样点的信息进行伪误码率统计，再利用伪误码率与信噪比之间的对应关系进行一一映射，从而得到信噪比估计值。

Evaluation methodology used in SearchE system is totally an automatic method. System uses the users' click analysis to construct the query set and mark the answer set automatically.

&搜索仪&系统所采用的评价，完全是基于自动方式的评价结果，系统使用用户点击行为分析的方法进行查询集合的构建以及对应答案自动标注。

For now check out the problem of pin VGA to VGA plug down to find the corresponding spot on the board PCB, found in open, re-repair welding on it.

对于检查出中现问题的VGA针脚，可以顺着VGA插头找到PCB板上的对应焊点，发现断路，重新补焊就可以了。

Introduced the analysis and processing of a transformer with three-phase winding of DC resistance imbalanced defect,through further analysis of the after processed DC resistance,believed the transformer still existing the polarity selector"-" side contact deficiency,further on finding out the method of comparing corresponding DC resistance difference rate at each tap has the advantage to detect the polarity selector defect more accurately more sensitively and more directly.

对一台变压器出现三相绕组直流电阻不平衡缺陷的分析和处理情况做了介绍；通过对处理后直流电阻的进一步分析认为，该变压器还存在极性选择开关&－&向侧仍有接触不良方面的缺陷，遂进一步提出，如采用比较各对应分接位置下直流电阻差率的方法能够有更准确、灵敏、直接地发现极性选择器方面缺陷的优点；还提出了测试变压器绕组直流电阻时的几点注意事项。

The results indicated that the isoelectric point of Al2O3 suspension shifted to acidic side and the absolute value of Zeta potential also increased when a dispersant was added into the suspension.

研究表明：加入分散剂使Al2O3悬浮液的等电点向酸性区移动，Zeta电位绝对值增大，其中pH值为9.56对应的Zeta电位绝对值最大，悬浮液最稳定。

The complexity of bodywork decides variety of it's error. The station and primary factor which cause error is inconstant change and using correlation analysis can find out the primary factor. With an project given, the theory of correlation analysis for dimension variation of bodywork is discussed through correlation analysis and the layer structure of the bodywork,the state in which the error happened can be found out. How to use eigenva...

车体装焊的复杂性决定了误差产生的多因素性，车体制造过程中产生误差的工位和主要因素是不断变化的，采用相关性分析方法从众多的误差根源中准确地发现最主要的误差源；结合工程实践，论述了车体尺寸波动的相关性分析方法的原理，根据测量点的相关性分析和车体焊接工艺的层次结构，可准确地找到产生车体尺寸误差的工位；讨论了如何利用相关系数矩阵的特征值和相应的特征向量判断尺寸波动的模式，指出测量数据的波动主要按最大特征值所对应的特征向量方式波动，引起这种波动的原因是车体误差产生的主要原因，应重点采取措施加以控制；提出了应用计算机进行相关性分析的解决方案。

Five different kinds of dynamic modes are found corresponding five regions in parameter space. In the region Ⅳ, the stable resting stable and stable limited circle of oscillation coexist.

通过改变描述心室肌细胞动作电位动力学的Beeler-Reuter方程的慢离子电导Gs和漏电流I，研究了Gs～Ⅰ平面上参数点对应的系统动力学模式和稳定吸引子性质。

It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.

从鲍尔点的形成原理出发，分析对称连杆曲线上鲍尔点的产生条件，提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。

The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.

集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品，年生产总值3000万美元，产品价廉物美、选料上乘、质量保证，深受国内外客户的青睐