对圆的

The results show that the number, length and width of the slots influence evidently the vibration behavior and thermal deflection of the circular saw.

对于分别开3、4、5、6个不同长度和宽度径向槽的圆锯片，径向槽的数量、长度、宽度对木工圆锯片的动态稳定性和热变形都有不同程度的影响。

This paper researches the part third-order contact condition of tool and the surfaces by the contact principle of deferential geometry in to the 5-axis NC machining and analyzes the contact degree of the intersection line of the cutter and the surfaces.

运用微分几何中的切触原理，研究了在多轴数控机床中铣刀铣削圆与零件曲面的切触条件和局部坐标系下的局部三阶切触条件，并用截形对铣刀铣削圆与曲面的贴近程度进行了分析。

The second research has also got that a function of slopes to C values is monotone decreasing function when target circles are bigger than distractors circles.

研究二针对目标圆大于干扰子圆大的条件，得到的目标搜索斜率对C值的函数也是单调递减函数，并确定了平行搜索与系列搜索的临界点〓（0.497）。

First, orthogonal circle operator was modeled in terms of Zernike orthogonal complex moment; the one-to-one mapping between the edge point and the parameters of the circle was established by the algorithm. Then, quadratic polynomial interpolation was adopted to further locate the edge points in the gradient direction.

首先根据Zernike正交复数矩建立圆物体边缘点与边缘参数之间的映射关系，并提取边缘点；然后利用二次多项式插值在梯度方向上对提取出的边缘点进行进一步定位；最后利用最小二乘法拟合插值后的边缘点，得到亚像素精度的圆参数。

The orthogonal expansion of the solution of the rotating disk motion equation is analyzed, and the stability of the system that includes the controller and the dynamics of sensor and actuator are analyzed.

本文通过对旋转圆盘运动方程解的正交级数展开的分析，由此在考虑控制器、作动器和传感器的动态特性情况下，分析了旋转圆盘振动主动控制系统的稳定性，指出了系统失稳的条件。

The computer simulations show the validity of the new method. The orthogonal expansion of the solution of the rotating disk motion equation is analyzed, and the stability of the system that includes the controller and the dynamics of sensor and actuator are analyzed.

本文通过对旋转圆盘运动方程解的正交级数展开的分析，由此在考虑控制器﹑作动器和传感器的动态特性情况下，分析了旋转圆盘振动主动控制系统的稳定性，指出了系统失稳的条件。

It is in this background that the displacement formula of flattened Brazilian disc for orthotropic material is proposed.

改进后的平台巴西圆盘克服了集中力产生应力集中的缺点，正交异性材料则是对各向同性材料的推广，在这样的背景下提出正交异性巴西圆盘试样的压缩位移公式。

All facilities of machinery have been imported from Korea, at the same time that they are blessed with high precision of production capacity, according to perfective technological process, high precision of test method, scientific manage system and so on that strickly make all produce process had high quality.

总投资200万美圆，注册资本150万美圆，所有的机械加工设备都是从韩国引进并具有高精密的机械性能，以完善的加工流程，高精密的测试手段，科学的管理体系对整个生产过程加以严格的控制确保产品质量。

C Taking the short-fiber reinforced and inhomogeneity spreaded composite materials as engineering background, singular integal equations of plane problem of interaction between line inclusion and circular inclusion are deduced, and some particular cases are analysed.

以短纤维和颗粒弥散体复合材料为背景，导出了线夹杂与圆夹杂相互作用平面问题的奇异积分方程，并对一些特殊情形作了退化分析，建立了数值法，给出了圆夹杂和线夹杂两侧的界面应力及线夹杂端点的应力强度因子表达式，同时作了具体的数值计算。

My grandpa's house is pretty flash, actually, except for an arch in the interior of the house which I thought was completely unnecessarily decorated with supposedly 'Greek' and 'Roman' curves and leaves and all that stereotypical intoxicants related with this certain genre.

那座公寓布置的相当舒适整洁，除了房间里头有一个十分无聊的罗马式圆拱。这个圆拱我认为是一个败笔，勾起了我对这种所谓欧式公寓的诸多不佳印象。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。