宽度

Range of kerf width and exposure may be changed for optimized performance.

一系列的切缝宽度和曝光可能会改为优化的表现。

This is achieved by using a unique multi beam technology, demonstrated in figure 2, which reduces the power density, minimizes the thermal load, and reduces the kerf width in the wafer.

这是采用独特的多光束技术实现的，图2显示了其工作原理，降低了功率密度，减小了热负载，缩小了刻线宽度。

Cutting machine used to cut sheet alloy up to 1 meter in diameter, which saw kerf depth of up to 40 cm, while the width, but 0.8 centimeters.

切割机用的合金切割片直径达1米，其锯缝深度可达40厘米，而宽度不过0.8厘米。

Second, a 3D unsteady-state numerical model of heat transfer in laser circular cutting of pipe was set up for the first time, and the kerf width, the cut front profile, the temperature field and the heat affected zone were calculated by using the model.

其次，首次建立了管材激光圆周切割传热过程的三维非稳态温度场计算模型，并计算了不同管径和切割速度条件下的切缝宽度、切割前沿及其相邻基材的温度场和热影响区大小。

The results showed that with the increasing of repetition frequencies, power density, and pulse width of laser beam and with the decreasing of scanning speed, the kerf quality could be improved. Besides, a formula of estimating the kerf surface roughness was also presented, which can explain the experiment results well.

在加工电子行业中表面组装用的模板时，一般采用化学刻蚀法，其缺点是加工精度低、工序多、周期长，特别是受刻蚀因子的限制，模板的最小缝隙宽度不能低于模板厚度的 1 2 ，因而难以满足日益发展的微电子技术对电子线路制作精度的要求。

With longger fruit and more key fruits,moreover, the two traits showed significantly positive correlation (r=0.888). Of the 11 floral and fruit quantitative traits, the length and width of perianth segment and 6 other traits were different significantly among the three groups,which were successfully used in group-discrimination by means of the method of principal component analysis.

在所研究的11 个花果数量性状中，花被片长度和宽度等10 个性状在三大类群间差异极显著，主成分分析结果表明第1 主成分(贡献率69.11%)综合了各性状的主要信息，依据第1 主成分可以对三大类群进行区分，其中北美鹅掌楸类群第1 主成分值最大(变幅0.7156～1.3916，平均1.0408)，杂交鹅掌楸类群(变幅-0.0865～0.3959，平均0.2646)居于两个亲本类群之间，鹅掌楸类群(变幅-1.5443～-0.8855，平均-1.2426)最小。

King-sized Bed – A bed that measures 76" in width and 80" in length.

王大中床-一张床措施7 6条"，在宽度和8 0"长度。

The OA kneepad with PIC16F630 microcontroller core can control the output signal frequency, pulse width, intensity and work time by controlling keyboardbuttons.

1 以PIC16F630单片机为系统控制核心的OA护膝，可通过键盘按钮控制输出信号的频率、脉冲宽度、强度和工作时间。

Development of OA kneepad : The kneepad density-wave output can be controlled by 2Hz different frequencies to 300 Hz stimulation pulse component, the pulse width of 100 to 150 μ s between the positive and negative output symmetry to the stimulation pulse. The rechargeable mobile phone batteries ( 3.7V) were served as power supply and SCM as timer with automatic shutdown after 30 minutes.

OA护膝的研制：护膝输出的疏密波可控制由2～300Hz不同频率刺激脉冲组成，脉冲宽度在100～150μs 之间，输出正负向对称的刺激脉冲，采用可充电的手机电池(3.7V)供电，单片机定时，30min 自动关机。

The knothole width should choose of appropriate, concrete knothole thickness general take 1 m as unit.

板的宽度应选的适当，混凝土板的厚度一般以1m为单位。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。