定理
- 与 定理 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
The purpose of this paper is to estimate the eigenvalues of square quaternion matrices.
估计定理,在估计定理的基础上提出了对角线元素是实数的四元数方阵的特征值。等式
-
In addition, the concept of generalized fuzzy quotient group is introduced and the correspondence theorems of generalized fuzzy quotient groups and fuzzy quotient subgroups are obtained respectively under group homomorphism.
另外,我们引入广义模糊商群概念,建立了环同态下广义模糊商群的对应定理及模糊商子群的对应定理。
-
This paper takes one low-speed-circumgyrate rocket with a empennage asa research object, set up a relevant reference frame, analyse the strength andmoment on the amended rocket, ratiocinate the sports equation with 6 DOF; analyse the factors which cause terminal windage between pratical trajectoryand fiducial trajectory, take certain rocket for example, make use of theemluator on the influence of estimating precision caused by measuredinformation, find the speed, the trajectory obliquity, the trajectory setoverand the coordinate are the sensitive factor arosing terminal windage of thetrajectory; introduce the developing status of detecting technique, and basedon the actuality, choose the radar in the ground as measure equipment; simplydesign and analyse the setting and inflame control of the impulse engine onthe amended rocket; design the amend method and validate its feasibility takingthe use of emluator.
本文以某型低速旋转尾翼火箭弹为研究对象,建立了相应的坐标系,详细的分析了作用在弹道修正弹上的力和力矩,由动量定理和动量矩定理推导出了在一般形式下的弹道修正弹的空间六自由度的运动方程;对引起弹道落点偏差的因素进行了分析,以某口径火箭弹为例仿真了可测信息量对估算精度的影响,发现速度大小、弹道倾角、弹道偏角和位置坐标是引起落点偏差的主要因素;对弹道探测技术发展现状作综合性阐述,并基于现状,选用地面火控雷达作为测量装置;对弹道修正弹上脉冲推力器的安装和点火控制方法进行了简要的设计与分析;设计了弹道修正弹指令修正的修正方法,通过数字仿真验证了方法的可行性。
-
Reciprocal theorem for non-linear elasticity with finite displacements in rectargular cartesian coordinates is established in this paper and reciprocal theorems for bending of thin plates with large deflections are given.
建立了直角坐标系有限变形非线性弹性力学的倒易定理并给出了大挠度弯曲薄板的倒易定理。
-
The solutions of thin bending rectangular plate with one subtense edges simply supported and the other subtense edges free, large deflection under uniform pressure are obtained by the Reciprocal Theorem Method in this paper. From the results it can ha found that the method is valid in non-linear questions and develops a new access.
主要应用大挠度弯曲薄板的第二类功的互等定理,求解在均布载荷作用下一对边简支一对边自由矩形板的挠曲面方程,计算结果表明,大挠度弯曲薄板功的互等定理在解决非线性问题方面简单有效,为求解相关大挠度问题开辟了一个新的途径。
-
The generalized magnetostatic field reciprocity theorem is deduced by the language of differential forms.
应用微分几何语言导出了广义静磁场互易定理,并应用该定理推导了漏磁无损检测数值分析中的富内德和蒙积分方程和线圈电感增量公
-
The conventional numerical simulation of a reverberant field as a launch acoustic environment was introduced. Following the reciprocity theorem used in the coupled FE-BE model, the structural response due to reverberant acoustic excitation was substituted by the sound pressure caused by force excitation on the structure, then the output response power spectrum density of the coupled model subjected to reverberant environment was evaluated based on the stochastic analysis principle.
首先介绍了传统的构建混响声场的数值模拟方法;其后利用声振耦合中的互易定理,将混响声场的激励问题转化为结构模型上力激励引起的场点声压响应问题,并采用随机分析原理,用谱分析方法推导了结构在混响声场激励下的响应计算公式;最后建立了航天器典型结构的声振耦合模型,并分别用传统方法和利用互易定理的方法进行了数值模拟。
-
Classic Chinese Remainder Theorem solving program, you have to import the solution congruence theorems can be solved by!
经典的中国剩余定理求解程序,输入你所要解的同余式即可按定理求解!
-
This paper proposed a directed threshold signature scheme based on the Chinese Remainder Theorem and Schnorr's signature scheme.
文章运用中国剩余定理,提出了基于中国剩余定理、ELGamal公钥密码理论和Schnorr理论的有向门限签名方案。
-
Of course, the major reason for this is that the basic algorithms are very complex (such as Chinese Remainder Theorem, Theory of Quadratic Residues, and many kinds of cryptagraphic algorithms).
当然造成这种结果的原因是因为实现这些方案的基础算法很复杂(例如中国剩余定理、平方剩余定理以及各种密码算法)。
- 推荐网络例句
-
It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.
从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。
-
The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.
集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐
-
The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.
血精的原因很,以良性病变为主。