孔洞

The styrene-acrylate spheres were coated with the TiO2 colloidal particles via electrostatic effect and hydrogen bond interactions with the increase of aging time, thus the film-forming capability of the solution was changed. The poor film-forming capability results in the formation of the porous structure with dense, homogeneous island morphology. Then the TiO2 porous films with dense pores can be obtained after two coating-dissolving cycles.

结果表明，TiO2溶胶与苯丙乳液混合后，陈化时间的延长有利于TiO2胶粒通过静电、氢键作用在苯丙乳液粒子表面形成吸附层，从而改变涂膜液的成膜性，形成较为密集、且均匀分布的岛状多孔结构，在此基础上经两次涂膜，即可获得具有致密孔洞的TiO2多孔薄膜。

Using this the problem can be summarized into scattering of SH-wave around an elliptic cavity in full space. Finally, the solving can be reduced to the solution of a series of algebraic equations.

应用这一波函数，将半空间中的问题转化为求解一个全空间中椭圆形孔洞的散射问题，最终将问题归结对一组无穷代数方程组的求解。

It is found that organic nanotubes from keto-enol isomeric dibenzoylmethane with different diameters show unique size dependent properties according to our experimental and calculated results. With the diameters of the nanotubes decreasing, the enol isomers of DBM molecules increased, the intensity of the fluorescence emission enhanced.

制备了平面稠环分子苝的纳米管，发现纳米管的形成机制源于模板孔洞的高长径比及溶液在高表面能基体上的自发铺展过程，苝层层沉积从而形成纳米管，苝分子头对尾的聚集体是形成纳米管的主要成份。

Finally, the gaps of the scan body were filled in under the control of a given error limit. The processed data facilitates the measurement extraction, etc.

最终填补了点云中的孔洞，使得处理后的数据便于尺寸提取等后续工作。

The study's findings indicate: the unconfined compressive strength of red sandstone is mainly lined with compaction rate, pore distribution and condition of being linked with grains and the above factors have a more notable impact on its unconfined compressive strength; grains' area ratio and Euler number decrease as a whole, pores' directionality gradually increases, stability of its internal structure reduces.

研究结果表明：红砂岩的单轴抗压强度主要与密实程度、微孔洞等缺陷的分布情况及颗粒之间的联结状态有关，随着红砂岩风化程度的增强，以上各因素对其单轴抗压强度的影响将更加显著；随荷载的增加，红砂岩的颗粒面积比例及欧拉数总体上趋于减小，孔隙分布分维趋于增大，内部结构的稳定性不断降低。

The findings indicate that under uniaxial compression, the red sandstones at first experience structural intensification and then structural degradation until they are failed; the unconfined compressive strength of red sandstone is mainly related with compaction rate, pore distribution and connecting condition of mineral grains; and the above factors have a more notable impact on the unconfined compressive strength of red sandstone with the increase of weathering; with the increase of load, the grains area ratio and Euler number decrease, the pore develops towards centralization or collectivization, and the red sandstones gradually lose their resistance to deformation.

研究结果表明：在单轴压缩条件下，红砂岩先结构强化，后结构劣化，直至最终破坏；红砂岩的单轴抗压强度主要与密实程度、微孔洞等缺陷的分布情况及矿物颗粒之间的联结状态有关，随着红砂岩风化程度的增强，以上各因素对其单轴抗压强度的影响将更加显著；伴随荷载的增加，红砂岩的矿物颗粒面积比例及欧拉数总体上趋于减小，孔隙向着集中化和集团化的趋势发展，红砂岩抗变形能力逐步丧失。

Fenestrate or perforated leaves are a special peculiarity of some genera of this family.

本科有些属特别具有多孔洞的叶

Compared with the graphite, the coefficients of friction of the RL-C/C are lower under the same load of about 0.08-0.12, and the increasing range of the volume losses are still lower than those of the graphite. Compared with the SL pyrocarbon material, the COF and the volume loss of the SL-C/C are about 0.02-0.05 and 0.2 mm^3, lower than those under the same load. The COFs of most RL-C/C and SL-C/C specimens remain stable or decrease slightly with time, while those of the graphite and pyrocarbon specimens increase. The thickness of the integrated friction film of the RL-C/C decreases with load, but the wear surface of the SL-C/C is rough. Tough the wear surface of the graphite is integrated, the serious abrasive wear make the debris move easily and accumulate on the edge of the wear trace to form a restacked morphology. On the wear surface of the pyrocarbon material, some loosed debris, circular worn holes and flake worn out pyrocarbon has been found.

结果表明：PAN炭纤维改善C/C复合材料的摩擦磨损行为；在实验载荷范围内，与高强度石墨材料相比，含RL炭C/C复合材料的摩擦因数降低0.08~0.12；体积磨损量增幅降低；与热解炭试样相比，具有SL炭C/C复合材料的摩擦因数降低0.02~0.05，体积磨损量低0.2立方公厘左右；随着时间的延长，大部分C/C复合材料的摩擦因数基本相对稳定或呈小幅下降，而石墨、热解炭块的摩擦因数均呈不同幅度的上升；具有RL炭的C/C复合材料摩擦表面膜厚度随载荷增加而降低，具有SL炭的C/C复合材料摩擦表面较粗糙；高强石墨能形成较完整致密的摩擦膜，但磨粒磨损严重，磨屑易在摩擦膜边缘形成层状堆积；热解炭块摩擦表面磨屑堆积松散，有较多的孔洞以及热解炭层整体剥落的形貌。

Compared with the graphite, the coefficients of friction of the RL-C/C are lower under the same load of about 0.080.12, and the increasing range of the volume losses are still lower than those of the graphite. Compared with the SL pyrocarbon material, the COF and the volume loss of the SL-C/C are about 0.020.05 and 0.2 mm3, lower than those under the same load. The COFs of most RL-C/C and SL-C/C specimens remain stable or decrease slightly with time, while those of the graphite and pyrocarbon specimens increase. The thickness of the integrated friction film of the RL-C/C decreases with load, but the wear surface of the SL-C/C is rough. Tough the wear surface of the graphite is integrated, the serious abrasive wear make the debris move easily and accumulate on the edge of the wear trace to form a restacked morphology. On the wear surface of the pyrocarbon material, some loosed debris, circular worn holes and flake worn out pyrocarbon has been found.

结果表明：PAN炭纤维改善C/C复合材料的摩擦磨损行为；在实验载荷范围内，与高强度石墨材料相比，含RL炭C/C复合材料的摩擦因数降低0.08~0.12；体积磨损量增幅降低；与热解炭试样相比，具有SL炭C/C复合材料的摩擦因数降低0.02~0.05，体积磨损量低0.2 mm3左右；随着时间的延长，大部分C/C复合材料的摩擦因数基本相对稳定或呈小幅下降，而石墨、热解炭块的摩擦因数均呈不同幅度的上升；具有RL炭的C/C复合材料摩擦表面膜厚度随载荷增加而降低，具有SL炭的C/C复合材料摩擦表面较粗糙；高强石墨能形成较完整致密的摩擦膜，但磨粒磨损严重，磨屑易在摩擦膜边缘形成层状堆积；热解炭块摩擦表面磨屑堆积松散，有较多的孔洞以及热解炭层整体剥落的形貌。

The lower die shoe often has machined or flame-cut holes that allow slugs and scrap created in the die to fall freely through the die shoe onto the press bed.

本句中的 that allow 引出定语从句，修饰 flame-cut holes ；全句译文：下模座往往具有加工完的或火焰切割后的孔洞，这样可使模具中产生的金属块和金属碎片经过模座自如降落到压床上。

For a big chunk of credit-card losses; the number of filings (and thus charge-off rates) would be rising again, whether

年美国个人破产法的一个改动使得破产登记急速下降，而后引起了信用卡大规模的亏损。

Eph. 4:23 And that you be renewed in the spirit of your mind

弗四23 而在你们心思的灵里得以更新