孔

Through the research of this paper, a conclusion can be drew: NaCl treatment raise the NH4＋-N removal ratio obviously by 18%, and is better than treating by heating, H2SO4, HCl and NaOH. The most reasonable concentration of NaCl is 0.8~1.0mol/L considering technical, economic and other factors synthetically; The best conditions of NaCl modifying is as follows : temperature 70~75℃, time 2.5hours, granularity ＜120mesh, volume/mass 25ml/g; As additive forming pores, activate carbon powder is a little better than charcoal powder, but the effect of both is much better than sawdust.

通过本论文的研究得出以下结论：NaCl改性能明显提高沸石对氨氮的去除效率，氨氮去除率提高了18%以上，其改性效果优于加热、H2SO4、HCl、NaOH等处理方法，综合考虑技术经济等因素的影响，取0.8～1.0mol/L为最合理的改性浓度；NaCl改性的最佳条件如下：温度70～75℃，时间2.5h，沸石粒径＜120目，体积质量比25ml/g；作为微孔沸石的造孔剂，活性炭粉略优于木炭粉，但二者的效果均比木屑好得多。

In addition, the exfoliation and intercalation of three kinds of novel layered aluminophosphate are investigated systematically, and mesoporous materials with high surface area chromium oxide supported aluminophosphate are synthesized successfully.

同时对三种层板具有规整微孔结构的层状磷酸铝的剥离与嵌入进行了系统研究，并成功地制备了高比表面的微介孔材料——铬柱磷酸铝。

The fit clearance between cylinder shaft hole of wire coil and supporting shaft should be 0.1mm to 0.5mm.

在装线盘时，先要检查线盘与顶头之间的配合性能：通常线盘圆柱轴孔与顶头之间的配合间隙应在0.1mm～0.5mm之间：锥形轴孔与顶头的锥度偏差

In order to increase the rolling capability of three-high cogging mill,the forging plant of Laigang reforms the traditional cogging process,joining the six angle-square pass with box pass well and designing the six angle pass with heavy elongation to realize conjugate rolling,thus realizing the heavy reduction,heavy elongation for cogging rolling and single end product outing and self nip,improving the rolling rhythm.

为提高三辊开坯轧机的轧制能力，莱钢锻压厂对传统的开坯工艺进行改造，将六角—方孔型与箱形孔良好衔接，并设计了能够共轭轧制的大延伸六角孔，从而实现了开坯轧制大压下、大延伸，以及成品单出与自动咬入，提高了轧制节奏。

The web perforation can provide space for electrical conduits and bracing. Therefore, it has the meanings and motive for the study of C-shaped section with web openings. The strength of a compression member can be influenced by the section shape, thickness of section, length of member, and support condition.

不过，构材之厚度、加劲与未加劲、是否开孔、上下两端之接合方式，皆会影响受压构材之抗压能力，所以目前先针对C形断面构材的开孔与否及上下两端之接合方式，分别以两种尺寸来讨论，并藉由有限元素分析软体ANSYS 6.0版，来模拟构件受压时，断面的应力分布情形。

Mesh of main raw material for stainless steel plate, aluminum, copper, steel, steel mill, the surface coating, coating, can be as hot galvanized processing, its mesh shape, size and size can be customized according to the different needs of customers.

冲孔网主要原材料为不锈钢板、铝板、镀锌板、冷轧钢板、铜板等，其表面可进行喷塑、喷涂、冷热镀锌等加工处理，其网孔的形状、大小及尺寸均可根据客户的不同需求定做。

Stem leaves narrowly oblong to narrowly elliptic, glabrous or sparsely short strigose abaxially; pedicel to 0.2 cm; calyx pubescent along midvein; corolla limb 5-7 mm wide; abaxial aperture of nutlets ca. 0.6 mm

缺乏茎生叶狭长圆形到狭椭圆形，无毛或疏生背面；花梗到0.2厘米；花萼短柔毛沿中脉；花冠瓣片5-7毫米宽；小坚果的背面的孔约0.6毫米 14 Microula oblongifolia 长圆微孔草

Orient the new rod coupling such that the hole in the coupling aligns with the hole on the hydrant rod.

确定新的阀杆连接套的位置，连接套上的孔与阀杆上的圆孔对齐，用销钉和开口销将连接套固定。

The MNCs were cultured on 96-well culture plate, with 0.2 mL in each well.

在96孔板上培养，0.2 mL/孔，14 d计数早期红系祖细胞，6 d计数晚期红系祖细胞。

By this the system, bovine preantral follicles in different diameters were cultured in vitro;and the effects of the number of follicles in each well of culture plate, different concentrations of NGF, Vitamin E, and Vitamin C on in vitro development of preantral follicles were studied.

在96孔培养板中，每孔25μl培养液的条件下，利用此系统研究了卵泡的入培直径、共培养卵泡数及神经生长因子、维生素C和维生素E对腔前卵泡体外发育的影响。

As she looked at Warrington's manly face, and dark, melancholy eyes, she had settled in her mind that he must have been the victim of an unhappy attachment.

每逢看到沃林顿那刚毅的脸，那乌黑、忧郁的眼睛，她便会相信，他一定作过不幸的爱情的受害者。

Maybe they'll disappear into a pothole.

也许他们将在壶穴里消失