孔

Because of the connecting rod is one of dyadic engine of piston and main compression engine part, whose larger end hole and crank shaft link up , the small head hole links up by the wrist pin and the piston , whose effect is that the piston gas pressure is transmitted to the crank shaft , collect crank shaft gas in driving but setting a piston in motion to compress a cylinder. the intensity is high.

因为连杆是活塞式发动机和压缩机的主要零件之一，其大头孔与曲轴连接，小头孔通过活塞销与活塞连接，其作用是将活塞的气体压力传送给曲轴，又收曲轴驱动而带动活塞压缩汽缸中的气体。

D. With 2-1/8 hole saw, cut holes in 2x4 yellow pine for one battery discharge

使用 2-1/8 孔锯，於 2x4 黄松木上锯孔，一个电池包。

The supramastoid crest and the superior rim of zygoma arch correlated with the level of the bottom of the middle fossa.

颞底经小脑幕手术入路骨窗为：第1孔位于乳突上嵴上，孔的后缘与顶乳突缝前角相切。

The results show that the bioceramic coating contains such bioactive phases as hydroxyapatite and tricalcium phosphate during laser cladoping. And the interlaced flake structure and micropores of about 0.5~2 μm in size exist on the surface of accidented gradient bioceramic coating, suitable to grow new bone along with the surface and micropore.

结果表明：激光熔覆复合涂层中生成了羟基磷灰石和磷酸三钙等生物活性相，凹凸不平的表面出现网络交错的片状结构和微孔(孔径为0.5~2 μm)，有利于新骨沿着表面及内部连通微孔攀附生长。

A comparison of the bleaching process of zooxanthellae from two different strony corals, Galaxea fascicularis andAcropora austeraField observation showed that in elevated sea water temperature Acropora austera bleached very fast whit while Galaxea fascicularis did not.

从野外采回不同珊瑚的共生藻，在光照下培养后发现自简单轴孔珊瑚分离出的共生藻较丛生棘杯孔珊瑚中分离出之共生藻容易丧失色素。

The pore width of the adsorbent among 1 nm～2 nm is over 90%.

发现吸附剂微孔含量在90%以上并且主要集中于1 nm～2 nm之间，是富含纳米孔的吸附材料。

According to the working procedure chart of theZH1105W diesel engine's gear cap analysis workpiece's precision, the surface roughness, thespecification, the processing spot size, the shape structure,material degree of hardness, the work piece rigidity and thedifferent of the components batch size to definite technique andtechnological process, determine aggregatemachine-tool's overall plan. Consider to theirregularity components but have high accuracy holes to beprocessing. So,"two holes at aface" is the best localization plan.

根据ZH1105W柴油机齿轮室盖的工序图分析其精度、表面粗糙度、技术要求、加工部位尺寸、形状结构、材料硬度、工件刚性及零件的批量的大小不同，确定被加工零件工艺方法和工艺过程，确定该组合机床的总体设计方案；考虑该零件表面结构的不规则性但有较高精度的孔需要加工，定位基准选择&一面双孔&是最佳的方法。

Silicon powders were mixed with pore-forming agent of 30wt% and agglomerant of 1wt% and shaped into discs of Φ70 mm×5 mm by mould pressing under pressure of 40 Mpa.

通过添加30wt%的成孔剂颗粒，制备出孔隙率在55%左右的具有宏观球形孔的多孔氮化硅陶瓷。反应烧结前，在低于硅熔点的温度下，对多孔硅坯体进行不同温度和不同时间的预烧。

Effect of aminate regent and time on the porous sructure of the APM carrier were studied.The SEM,IR,DSC and mercury porosimery were used to examine the structure and properties of the APM carrier.

用SEM、IR、DSC元素分析仪和孔度率仪对APM载体进行了测试，研究了胺试剂和胺解时间对APM载体孔结构和氮含量的影响。

And the production comprises that dissolving polyarylamide into organic solvent; mixing and adding alumina particles, disperser, holing agent to be vibrated via ultrasonic wave; putting into drying box to be aged and defoamed; irrigating into film; vaporizing it in drying box; putting into solidify liquid to be emerged; washing with distilled water, processing aminic acid solution, compressing and shaping.

分散剂0.6～8wt。％、成孔剂2～8wt。％组成，制备方法为：将芳香聚酰胺溶于有机溶剂中，在搅拌中加入氧化铝颗粒、分散剂、成孔剂超生震荡；放入干燥箱中熟化、脱泡；浇铸成膜；浇铸后的膜在干燥箱中蒸发，然后放入凝固液中浸泡，接着用蒸馏水漂洗干净后用甲酸溶液处理；最后预压成型。

I didn't watch TV last night, because it .

昨晚我没有看电视，因为电视机坏了。

Since this year, in a lot of villages of Beijing, TV of elevator liquid crystal was removed.

今年以来，在北京的很多小区里，电梯液晶电视被撤了下来。