孔

To resolve this problem, we'll reel outwards drive across the bridge to the intermediate surface of variable-speed drive wheel with two wheels of processed into 30 °, the increase in friction with Groove, even if such a belt would not have had; the diameter of 6 mm, spin out to o-rubber belt changed out with Burr corn-cob o-shaped belt; crossing the bridge to another variable-speed drive belt pulley to roll out of the book, two rounds of the belt pulley turned into 1/2 inch, using chain drive sprocket, and fixed machinewe side wall to cross the bridge wheel seat side wall plate processing growth holes for adjust tension pulley and sprockets.

为解决这个问题，我们将分切机朝外传动面传动到中间过桥变速皮带轮的两轮加工成30°的带槽，增加摩擦力，这样皮带即使松了也不会打滑；直径6mm的O型橡胶皮带改成外面带毛刺的聚氨酯O型皮带；过桥变速皮带轮的另一个传动到出书辊的皮带轮，两轮改成1/2英寸的链轮，采用链条传动，再将固定在机器侧墙板的过桥轮座侧墙板孔加工成长孔，可任意调整皮带轮与链轮的松紧。

On the basic of it chatter of cutting processes is analyzed by speed feedback and displacement delaying feedback and curial condition of stability cutting is discussed. Secondly, dynamic model of deep-hole drilling system with the two degrees of freedom are established in the light of principles of machining chatter in cutting processes.

本文针对深孔加工系统的特点，首先分析了深孔加工的力学特性，并在此基础上，根据金属切削中的颤振现象，对金属切削过程中由于速度反馈和位移延时反馈所引起的颤振现象进行了分析，并分别讨论了稳定切削的临界条件。

The Tertiary reservoir in the vertical orientation develops three high porosity zones, every one firstly occurs in the sandstone of debouch bar and braided-divided flow channel, secondly occurs in the sandstone of raised bank and channel bar.

第三系储层在纵向上发育三个高孔带，各高孔带主要发育在沉积微相为河口坝、辫状分流河道的砂体中，其次发育在天然堤和心滩的砂体中。

Posterior cranial cavity heteromorphosis and crowded nervous tissues in debouch of inferior foramen occipital may be the reasons of the kind of cervical vertebra sickness symptoms and the latter group cranial nerve symptoms,so we suggest calling this group of symptom the debouch of inferior foramen occipital crowding syndrome.

后颅腔形态变异和枕骨大孔出口神经组织拥挤可能是类颈椎病症状和部分后组颅神经症状的原因，建议将这组症状称为枕骨大孔出口拥挤综合征。

Professor Kong De-Qing is one of the most well recognized 77th decedent of Confucius.

孔德清教授是名声显赫的孔夫子77代后裔之一。

Experiments were carried out concerning drilling of CFRP, using solid carbide drills and diamond drills. It was found that the diamond drill were an ideal tool for drilling of CFRP.

本文最后对碳纤维复合材料高质量制孔技术进行了试验研究，给出了几种金刚石钻头的结构，经钻削试验发现金刚石钻头是碳纤维复合材料高质量制孔的良好工具和今后发展方向。

On a diatonic, essentially you have three holes that really sound good.

在布鲁斯口琴上，有3个孔是最动听的，特别是第3孔。

Gage hole dimeter , hole diameter and overall slot size their have difference tolerance.

测量孔直径，孔直径和所有槽的尺寸，均有不同的公差要求。

When the soil surface is fully mulched with plastic film, salt concentration is a exponential function of depths. With different film hole ratios and wetting fronts depths, the salt concentrations can be expressed as a discontinuous function of the depth.

对不同开孔率来说，全覆膜蒸发的浓度可用深度的指数形式表达，不同入渗锋和开孔率条件下浓度可表示为位置的分段指数函数。

The result showed that the optimal linear velocity of hammer terminal were 35～45 m/s and 40～50 m/s(the average granularity is 1.30 mm)on minitype and large and medium-sized type of no-sieve disintegrator in smash corn.

结果表明：粉碎玉米时，小型与大中型锤片式无筛粉碎机锤片末端最佳线速度分别为35～45m/s和40～50m/s(平均粒度为1.0～1.3mm最佳)；最佳排粉方式为采用从动定盘间隙和定盘环面长条孔同时排粉；当长条孔宽度为4～6mm、线速度为43～47m/s时，成品的平均粒度在1mm左右。

The concept of equivalent rotationally rigidity is offered and the formula of rotationally rigidity is obtained.

主要做了如下几个方面的工作：对伸臂位于顶部的单层框架—筒体模型进行分析，提出了等效转动约束的概念和转动约束刚度的表达式。

Male cats normally do not need aftercare with the exception of the night after the anesthetic.

男猫通常不需要善后除了晚上的麻醉。