子系统

This research program "network application system of digital map ." serving as a segment of the main program "the digital map making system map maker", which is a research subject of the general section of weapon and equipments, is based on the thoughts of software engineering, and after systematically analyzed and designed by the means of UML( unify to set up the mold language), linked with C++ in general use, are able to directly converts the map data in DXF form into data in unified and open SVG form( the flexible form that can be updated), and realizes to view and interact SVG document accordingly via the JavaScript foot script language on the web page.

本课题作为总装预研项目&全数字地图制图系统Map Maker&的一个组成部分，即数字地图网络应用子系统，它根据软件工程的思想，经UML进行系统分析和设计后，通过C++通用接口，将存储为DXF格式的地图数据文件直接地转换为统一、开放的SVG格式文件(即可升级的矢量图形格式文件)，并且利用JavaScript脚本语言在网页上实现了对SVG文件的浏览和交互操作。

The master controller can be used to communicate with the slave controller implementing boundary scan test of testable subsystems.

IEEE1149.5主控制器可完成和从控制器间的通讯以便对机箱或子系统级中可测试性模件进行边界扫描测试。

In the base of these key technologies mentioned above, a Image Control System prototype has been built to satisfy the need of medicals.

基于以上关键技术的研究，作者构建了一个适用于我国网络资源现状、满足医护人员要求的图像控制子系统。

At this time if load is applied on mid-span, the subsystems will rotate around the damaged connection.

在跨中加载的情况下，各子系统绕着损伤横向连接发生约束扭转。

According to the emulate analysis, the harmonic amplitudes go bigger with the increment of misalign value for shafts with normal couplings, but may fall for one or two times.

仿真分析结果显示，连轴节无故障的不对中转子系统，各倍频振幅随着不对中量增加，总的变化趋势为逐渐增大，但中间会出现波动。

The results also revealed that the modes of the misaligned rotor system were different from the aligned one.

分析结果还表明不对中转子系统的模态与理想对中系统相比有较大的差别。

In this paper the test approaches and procedures for measuring the acceleration mobilities of rotor and fuselage subsystem and coupled system are introduced. The measured and calculated results for self-designed rotor/fuselage model are summarized and compared.

本文介绍旋翼／机身耦合系统模型及其子系统的导纳的测试方案、试验程序，综述以作者自行设计的旋翼／机身耦合系统模型进行试验所得到的结果及其与理论计算结果的比较。

The acceleration mobilities of rotor and fuselage subsystem and coupled system are key parameters for determining natural frequencies of the rotor/fuselage coupled system by using mobility matching method. We have deduced the analytical expressions. In order to verify the feasibilities of the expressions, it is necessary to measure those mobilities.

直升机旋翼和机身子系统以及其耦合系统的导纳是用动柔度匹配法确定直升机旋翼／机身耦合系统固有频率必要的数据，我们已推导了它们的分析表达式，为验证分析表达式的可用性，须进行试验测试与研究。

Combining the results of modal experiment analysis on body-in-white and the results of finite element analysis, structural dynamics modification on the car front-body of a monocoque body has been made based on optimization algorithm.

结合轿车白车身试验模态分析和有限元分析的结果，成功地对某承载式轿车车身的车头子系统结构进行了基于优化算法的结构动力学修改。

The structural function and its implement of TIDS System developed in the AutoCAD package are introduced in this paper. In this system, so long as a basic size and tolerance code are inputted by users at a time, the deviation can be searched and printed or dimensioned in the drawing directly. Thus, automation is completely realized to indicate tolerance in the CAD System.

本文介绍了作者在AutoCAD软件中开发的子系统TIDS的功能及其结构和功能实现等，该系统能根据用户一次输入的基本尺寸和公差带代号检索出极限偏差数值并作打印或自动标注，从而在CAD中完全实现了尺寸公差标注的自动化。

This one mode pays close attention to network credence foundation of the businessman very much.

这一模式非常关注商人的网络信用基础。

Cell morphology of bacterial ghost of Pasteurella multocida was observed by scanning electron microscopy and inactivation ratio was estimated by CFU analysi.

扫描电镜观察多杀性巴氏杆菌细菌幽灵和菌落形成单位评价遗传灭活率。