夹
- 与 夹 相关的网络例句 [注:此内容来源于网络,仅供参考]
-
The blog folder on the server, and the wordpress folder on your computer should be identical with regards to the contents.
服务器上的blog文件夹和你的电脑上wordpress文件夹,内容应该是一样的。
-
Unlock the Solo rope clamp to extend the block and tackle system down to the victim,then re-lock the Solo rope clamp
开启夹绳器放松绳索,延长滑轮组的绳圈到受灾者的身上,再锁上夹绳器。3。
-
Note that the blue bar shows which folder your browsing in at any given time.
注意蓝色色块标明那个文件夹是您正在浏览的文件夹。
-
Sometimes there could be seen gliding into the butcher's shop on the corner, in the midst of the bantering cooks who elbowed him, an awkward young man, carrying big books under his arm, who had a timid yet angry air, who, on entering, removed his hat from a brow whereon stood drops of perspiration, made a profound bow to the butcher's astonished wife, asked for a mutton cutlet, paid six or seven sous for it, wrapped it up in a paper, put it under his arm, between two books, and went away.
有时,人们看见一个形容笨拙的青年,一只胳臂夹着几本书,神气腼腆而莽撞,溜进那街角上的肉铺子,挤在一些嘴里没好话、把他东推西撞的厨娘中间,一进门便摘下帽子,满额头的汗珠直冒,对那受宠若惊的老板娘深深一鞠躬,继又对砍肉的伙计另外行个礼,要一块羊排骨,付六个或七个苏,用张纸把它裹上,夹在胳膊下的两本书中走了。
-
With some materials, this process will have to be repeated several times before a satisfactory butt weld is obtained.
用夹具夹住焊接线,用钳子夹住热电偶线,然后把两根线头对头接触,之后按焊接按钮。
-
Step two: in the "Operation source" page select "choose files and folders" and click "Next" button found in the document tree and check to backup files and folders, and then click "Next" button.
第二步:在"作业源"页面选择"选择文件和文件夹"后单击"下一步"按钮,在文件树中找到并勾选要备份的文件和文件夹,接着单击"下一步"按钮。
-
An operation lever displaceably pressed by the engagement piece for operation to operate the rope gripping mechanism is connected to the rope gripping mechanism.
绳索夹紧机构上连接有工作用杆,该工作用杆用于通过被工作用卡合件按压移动来使绳索夹紧机构工作。
-
This design is to dials forks the components the processing craft and the jig design, its components are the forging, has the volume to be small, components complex characteristic,Because the surface is easier than the hole to process, when formulation technological process, first the machined surface, then processes other take the surface as the datum,In which various working procedures jig all uses the unit clamp, special regarding processes the big end of hole, the trough and drills the capitellum hole incline eyelet in the working procedure, Chooses locate mode which two sells at the same time, and operates the simple manual clamp way clamp, its organization design is simple, the convenience also can satisfy the request.
此次设计是对拨叉零件的加工工艺和夹具设计,其零件为锻件,具有体积小,零件复杂的特点,由于面比孔易加工,在制定工艺规程时,就先加工面,再以面为基准来加工其它,其中各工序夹具都采用专用夹具,特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中,选一面两销的定位方式,并以操作简单的手动夹紧方式夹紧,其机构设计简单,方便且能满足要求。
-
This design is to dials forks the components the processing craft and the jig design its components are the forging has the volume to be small components complex characteristicBecause the surface is easier than the hole to process when formulation technological process first the machined surface then processes other take the surface as the datumIn which various working procedures jig all uses the unit clamp special regarding processes the big end of hole the trough and drills the capitellum hole incline eyelet in the working procedure Chooses locate mode which two sells at the same time and operates the simple manual clamp way clamp its organization design is simple the convenience also can satisfy the request.
此次设计是对拨叉零件的加工工艺和夹具设计,其零件为锻件,具有体积小,零件复杂的特点,由于面比孔易加工,在制定工艺规程时,就先加工面,再以面为基准来加工其它,其中各工序夹具都采用专用夹具,特别的对于加工大头孔、槽和钻小头孔斜面小孔的工序中,选一面两销的定位方式,并以操作简单的手动夹紧方式夹紧,其机构设计简单,方便且能满足要求。关键词拨叉,加工工艺,专用夹具,设计
-
This tuning may also be used with a capo at the third fret to match the common lute pitch:
这个调弦常常在第三品夹个变调夹来与普通的鲁特琴调弦G-c-f-a-d'-g'相匹配。
- 推荐网络例句
-
It has been put forward that there exists single Ball point and double Ball points on the symmetrical connecting-rod curves of equilateral mechanisms.
从鲍尔点的形成原理出发,分析对称连杆曲线上鲍尔点的产生条件,提出等边机构的对称连杆曲线上有单鲍尔点和双鲍尔点。
-
The factory affiliated to the Group primarily manufactures multiple-purpose pincers, baking kits, knives, scissors, kitchenware, gardening tools and beauty care kits as well as other hardware tools, the annual production value of which reaches US$ 30 million dollars.
集团所属工厂主要生产多用钳、烤具、刀具、剪刀、厨具、花园工具、美容套等五金产品,年生产总值3000万美元,产品价廉物美、选料上乘、质量保证,深受国内外客户的青睐
-
The eˉtiology of hemospermia is complicate,but almost of hemospermia are benign.
血精的原因很,以良性病变为主。