失效

The results show that the peak tension in the conductor of upper crossarm at suspension point exceeds the design value. Insulator rupture has no effect on tower component of upper crossarm, but it has significant influence on insulator tension of upper crossarm. The lower limit of longitudinal unbalanced tension of two and more than two bundle conductor is relatively small. Insulator rupture should be taken into account in the design for overhead transmission lines.

分析结果表明，上横担一组绝缘子破坏失效后，破坏档未破坏端导线的张力超过了技术规程中的设计值；导线的跌落对破坏档未破坏端的上横担绝缘子受力有较大的影响，而对上横担铁塔杆件没有明显的影响；考虑杆塔断线荷载时，应增大两分裂以上导线纵向不平衡张力的下限值；在架空送电线路的设计中应该考虑绝缘子断裂的荷载工况。

Butt,T-butt and cruciform weldments are typical joints in ship and ocean structures. Most of the fatigue failure can be traced to the weld toe.

对接、T型接头与十字接头是船舶与海洋结构的典型结构形式，其大部分疲劳失效是由于焊趾引起的。

119 4 And 0. 006 7, respectively. Both the failure probability density function and the cumulative distribution function can be presented by this degradation failure model.

所选的某型金属化膜脉冲电容器未知参数估计值为0.0001194和0.0067，将该值代入失效分布函数和概率密度函数中。

The characteristic function of the probability density function of response variable is obtained by the high efficient multidimensional numerical integration method or convolution integral based on response surface method. Then the discrete probability density function of response variable is calculated using the fast Fourier inverse transform technique, at last the cumulative distribution function of the response variable can be quantitatively determined.

首先利用高效多维数值积分方法或基于响应面法的卷积积分求解功能函数的分布函数的特征函数，也就是进行Fourier正变换；然后利用快速Fourier逆变换数值求解功能函数的概率密度函数，进而求得失效概率。

A general reliability model is constructed according to the distributed and real-time control demand of lower hybrid current drive system.

软件可靠性是指在规定环境下，在规定时间内软件不引起系统失效的概率；或在规定的时间周期内在所述条件下程序执行所要求功能的能力[1]。

The effect of tribology factors on bearing vibration is studied experimentally. AR model and WPT are used to processing the normal arid abnormal signals. The results are as follows:1. The vibration of ball bearings is caused by the tribology action of contact pairs of ball and ring races and has the essential of tribo-dynamics. Any factors affecting the tribology characteristics of contact pairs will affect vibration and noise of bearings consequently.2. Vibration characteristics of bearing keep almostly unchanged with the increasing of axial load expecting the increasing of nature frequencies. When radial load increasing with axial load unchanged, nature frequencies keep unchanged but some new vibration peaks appears in the spectrum.3. Vibration amplitudes are damped and nature frequency are enhanced with sufficient lubrication. Vibration and noise of bearings increase obviously and roar can happen and the contact surfaces scratch slightly under insufficient and unclean lubrication state. Bearing will be disabled in a few minutes without any lubrication.4. Bearing vibration is unstable under low speed. With the speed increasing, the vibration become stable and natural frequencies increase slightly but the amplitudes increase apparently.5. Bearing vibration can be excited only by some harmonics ofwaviness without lubrication and by all harmonics with lubrication based on the theoretical analysis.6. The nature frequencies of ball bearings decrease with the increasing sizes. When international clearance increasing, nature frequencies decrease in radial and increase in axial and angular and the amplitudes increase in radial and decrease in axial and angular. When the number of balls increasing, nature frequencies increase and amplitudes decrease. When the pitch diameter increasing, axial nature frequency increase and others nearly keep no change. When outer race groove curvature radius increasing, nature frequencies increase in radial and decrease in axial and angular and amplitudes keep no change in radial and increase in axial and angular. When inner race groove curvature radius increasing, nature frequencies decrease and amplitudes increase.7. The distortion in amplitude and frequency components of bearing vibration signals picked up by the present probe measurement method is founded and right conclusions cannot be achieved by the signals. When accelerometer is rigidly screwed with steel stud onto a flat outer surface of a ball bearing, vibration signal can be got without distortion and the reliability of research on bearing vibration is assured.8. AR model is suitable for large samples of bearing vibration signals, square root of length of samples can be used as the upper limitation of order determination and the FPE order selection criterion is effective. Many advantages of AR spectrum are founded over the classical based on FFT.9. Time-Frequency analysis is necessary for abnormal noise of ball bearings. WPT overcomes the principle shortcomings of STFT and proved to be a best tool to process the abnormal signals.

理论分析和试验研究表明： 1球轴承振动是钢球—滚道接触副中的各种摩擦学作用引起的，具有摩擦动力学的本质，任何对接触副的摩擦学特性有影响的因素都将对球轴承的振动和噪声特性产生影响； 2中心轴向载荷作用下，载荷增大使球轴承的固有振动频率升高，载荷越大同样的载荷增幅引起的频率升幅减小，足够大的中心轴向载荷作用下载荷的变化对球轴承振动的频率特性不会产生明显的影响； 3轴向和径向联合载荷作用下，径向载荷不大时球轴承振动的固有频率基本不变，但是可能引起变刚度激励的非线性振动，出现新的频峰，过大的径向载荷将使部分钢球脱离接触，使球轴承的振动和噪声呈现不稳定状态； 4润滑对球轴承的振动和噪声特性有重要的影响，良好的润滑对振动有明显的抑制作用，润滑不充分时，振动和噪声的水平会有明显增高，一定条件下还会激发接触副中的谐振，发出啸声，造成接触表面的伤害，无润滑干接触时，短时的运转就会损伤接触副表面，使振动和噪声迅速增大，并随时可能引发严重的磨损和卡滞失效；接触副润滑良好时，油膜的"刚化效应"使球轴承振动的固有频率有所提高，润滑剂中含有弥散性污浊时，振动的幅度总体升高，但弥散性污浊不会改变球轴承振动的频率特性；浙江大学博士学位论文：球轴承振动的研究 5低速时，球轴承振动的基本特征呈现不稳定状态，随着转速的提高，球轴承振动的频率特性趋于稳定，固有频率频峰升高； 6理论分析表明，干接触时钢球和滚道表面波纹度的某些谐波分量能激励球轴承的振动，振动的幅值与谐波幅值成正比，实际球轴承中钢球的分布不可能完全均匀，波纹度的激励作用会随时发生；润滑接触的分析表明，波纹度的任意谐波分量均能激励球轴承的振动； 7球轴承的几何和结构参数分析表明，球轴承尺寸越大，径向、轴向和角振动的固有频率越低；钢球中心圆直径增大，球轴承的径向和轴向振动的固有频率基本不变，角振动的固有频率有所上升，振动的幅频特性基本不变；径向游隙加大使球轴承的径向振动固有频率降低，轴向和角振动的固有频率有所升高，径向振动幅频特性的幅值升高，而轴向和角向降低；钢球的数量增多使球轴承振动的固有频率上升，幅频特性的幅值下降，径向振动的幅值下降最为明显；外圈沟曲率半径系数增大使球轴承径向振动的固有频率升高，轴向和角振动的固有频率降低，径向幅频特性基本不变，轴向和角向幅频特性幅值升高；内圈沟曲率半径系数增大使径向、轴向和角振动固有频率均下降，振动幅频特性的幅值均有升高； 8试验对比表明，传感器采用探针式安装时，由于探针接触副接触特性的影响，钡(量得到的球轴承振动信号有失真，采用专门设计和制作的试验球轴承，以固定式安装加速度计，首次测量得到了球轴承振动的真实信号，通过对振动信号的分析，验证了球轴承振动的理论模型； 9)基于时间序列分析的AR模型适用于大样本球轴承振动信号的分析，以样本长度的均方根值作定阶上界，FPE做判阶准则，给出的AR谱光滑，频率分辨率高，是球轴承振动分析的简便而可靠的手段； 10以时频域分析的小波包变换分析球轴承异音信号能够比较好地定位和聚焦异音发生的时间，时间间隔，频率范围，同样是球轴承振动分析的可靠的手段，可用作球轴承故障诊断技术。

But in this case it is deactivated.

但在这种情况下是失效。

An epidemic disease caused by an infection by human immunodeficiency virus (HIV-1), a retrovirus that causes immune system failure and debilitation and is often accompanied by cancers and secondary infections such as but not limited to tuberculosis.

一种由免疫缺陷病毒感染的人类传染病(HIV-1)，一种逆转录酶病毒引致免疫系统失效或者衰弱和经常伴随着癌症或者第二传染病例如肺结核，但不限于肺结核。

Crack propagation leading to decohesion or delamination is one of the major failure.

但在生产与使用过程中膜基界面处容易产生裂纹，裂纹的扩展导致膜层的脱落是使膜层完全失效的主要形式之一。

The prior cycles with higher axial stress and larger strain range greatly restrains ratchetting strain of subsequent cycling with lower ones. Creep behavior plays an important role in the ratchetting strain and its influence on ratchetting behavior can not be neglected. Fracture morphology characteristics of two kinds of materials were investigated by scanning electron microscope. It shows that failure of material A is induced by cavitation and that of material B is induced by decohesion. For material A, with the decreasing strain amplitude the fracture surface shows more larger diameter globular particles under uniaxial loading and can be seen more obvious and deep crack under multiaxial loading. However for material B, with the decreasing strain amplitude fracture surface shows larger and larger scalelike shape and becomes more smooth under uniaxial loading, but fracture surface under multiaxial loading looks like more smooth than that of uniaxial loading, and shows gradually wave-like morphology.

通过扫描电子显微镜研究表明：材料A为空穴引起的失效，材料B为剥离导致疲劳破坏；随着载荷幅值的减小，材料A在单轴载荷下，断口表面浮出更多更大直径的球状颗粒，而多轴载荷下，可以看到很深的裂纹；随着载荷幅值的减小，材料B在单轴载荷下，断口表面鱼鳞片越来越大，表面越来越平整，而多轴载荷与单轴载荷相比，断口表面看上去更加平整，并且随着载荷幅值的减小，断口逐渐呈现波浪形貌；通过微观的傅立叶变换红外光谱分析，结果表明随着应变幅值的增加，无论载荷是单轴还是多轴状态下，橡胶材料吸光度比值随着幅值的增加而增加，这说明体系中的结晶含量也随之增加。

However, as the name（read－only memory）implies, CD disks cannot be written onorchanged in any way.

然而，正如其名字所指出的那样，CD盘不能写，也不能用任何方式改变其内容。

Galvanizes steel pallet is mainly export which suits standard packing of European Union, the North America. galvanizes steel pallet is suitable to heavy rack. Pallet surface can design plate type, corrugated and the gap form, satisfies the different requirements.

镀锌钢托盘多用于出口，替代木托盘，免薰蒸，符合欧盟、北美各国对出口货物包装材料的法令要求；喷涂钢托盘适用于重载上货架之用，托盘表面根据需要制作成平板状、波纹状及间隔形式，满足不同的使用要求。