大轴

The results show that: when the stress triaxiality is low, the penny-shaped crack can lead to damage anistropy of a ductile material; and the variance of Lodes parameter will lead to the variance of the expanding rate and deformed shape of penny-shaped crack and sphere-shaped void.

进而对材料中同时含有币形微裂纹和球形微孔洞的情形作了数值模拟分析。计算结果表明：币形微裂纹的存在将导致低应力三轴度下韧性材料破坏的细观损伤呈现明显的各向异性；而Lode参数对微裂纹和微孔洞的长大和变形状态具有较大的影响。

Wheelies are an old trick that goes back at least as far as roller skating does and most likely much further.

Wheelies是故伎重演，可追溯到至少就滚轴溜冰不和最有可能更大。

As a result, it is difficult to measure the wavefronts of the laser beams by conventional wavefront sensors.

大功率激光二极管线阵特殊的发光区结构使它具有不理想的光学特性，特别是其快轴方向高达40°的大发散角，使得传统的波前探测器很难对其进行波前探测。

The vessel is powered by twp 1,100hp diesel, with two shafts, giving a maximum speed of 14 knots.

采用两台1，100马力柴油发动机，双轴，最大航速14节。

At present, brazing technology are widely adopted at home and abroad . In order to verify the availability and applicability of pulse Nd:YAG laser-welding, a comparison is made between the new technology and the present technology in such aspects as the dismantled torsions, the microstructure and the micro-hardness of the weld area and the heat-affected zone, the maintenance of fabrication precision and assembling precision of the components.

本文首次采用灯泵Nd：YAG脉冲激光进行焊接试验，并和硬钎焊获得的拆卸扭矩、焊缝金相组织、显微硬度等进行了综合对比，结果表明，激光焊接能很好地保证支架和支架轴固有的机械性能、耐磨性、加工与装配精度；激光焊连接可靠，耐拆卸扭矩大，符合整体结构性能要求；焊后无需后续处理，可以作为最终工序，验证了激光焊接的有效性、适用性。

Bob Teal discovered that very powerful electric motors could be built using electric solenoids pulling on a crank shaft system.

Bob Teal发现马力大的发电机能过通过螺线管吸引曲柄轴的系统。

The influences of settled material, bellout height and diameter on the bearing capacities of pile with straight shaft and pedestal pile are determined.

分析了桩底沉渣、扩底高度和扩底直径对大直径等截面桩与扩底桩承载特性的影响，得出桩身轴力、桩侧阻力和桩顶沉降等变化规律。

To reveal aft end internal flow feature of a solid rocket motor with submerged nozzle, a two dimension cold flow test model with rectangular channel was designed The cold gas simulation was based on geometric similarity and aerodynamic analogy Mean and fluctuating velocity field was measured using phase doppler particle analyzer It showed that the flow separates at upstream of the submerged nozzle and reattaches on the tip of the nozzle nose A relatively steady recirculation zone formed in...

为了揭示含潜入喷管的固体火箭发动机尾部流动特征，按照几何相近和气动相似原则设计了通道为矩形的二维冷流实验模型，利用相位多普勒粒子分析仪对燃烧室尾部气流的时均速度和湍流脉动速度进行了测量。实验结果表明气流在潜入喷管入口上游发生分离，再附点位于喷管前端部外侧，背壁空腔内形成一个较为稳定的回流区，流场的轴向和横向湍流强度都比较大

As a downstream piping system when the valve opens, reflux valve, when closed, the main medium used to prevent backflow to prevent the pump and drive motor reversal, as well as a container medium discharge; currently the most commonly used is the valve flap around the body Swing Pin rotation flap valve and the valve body along the vertical axis to move lift check valve, but the above two kinds of structures exist in the valve closed, medium speed back quickly from the largest drop to zero, inlet side of the pipe resulted in the rapid pressure rise, resulting Proportional Pressure Reducing Valves in damaging effects on the piping system of water hammer phenomenon, it is generally a diameter of valve production of 50 ~ 500 mm.

止回阀作为管道系统顺流时开启，逆流时关闭的阀门，主要用于防止介质倒流，防止泵及驱动电机反转以及容器内介质泄放；目前使用最普遍的是阀瓣围绕阀体销轴旋转的旋启式止回阀和阀瓣沿着阀体垂直中心线移动的升降式止回阀，但以上2种结构的阀门均存在关闭时介质倒流速度从最大迅速降为零，致使管道进水管一侧内压迅速升高，从而产生对管路系统有破坏作用的水锤现象，所以一般止回阀生产口径为50～500 mm。

Radial piston pump can be divided into the valve with flow and axial flow with two broad categories.

径向柱塞泵可分为阀配流与轴配流两大类。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。