大轴

In the paper,the transmission of designed roller oscillating tooth reduction gear adopts osci llating tooth gear drive without exception,one-stage reduction gear and two-stage reduction gear have joined through spline coupling band;The joining way of shock wave thellomble and oscillating tooth adopts the biserial bearing of without inner ring of needle bearing,and directly adopts bearing outer ring as shock wave thellomble;Center wheel of two-stage reduction gear and center wheel of two-stage reduction gear passes through taper thread,and center wheel is fixed;As soon as the flange of input end and center wheel of one-stage reduction gear,the flange of export end and center wheel of two-stage reduction gear makes monobloc structure.

本文预设的井下减速器的传动均采用活齿传动，一级减速器的输出轴和二级减速器的输入轴通过花键联轴套联接；激波环与活齿的毗连方式采用能蒙受较大载荷的无内圈双列滚针不锈钢管，且直接采用不锈钢管外圈作为激波环；一级减速器的中心轮和二级减速器的中心轮是通过锥螺纹毗连的，且中心轮固定；一级减速器的中心轮与输入端的法兰盘，二级减速器的中心轮与输出端的法兰盘均做成整体的结构。

In the paper,the transmission of designed roller oscillating tooth reduction gear adopts oscillating tooth gear drive without exception,one-stage reduction gear and two-stage reduction gear have joined through spline coupling band;The joining way of shock wave thimble and oscillating tooth adopts the biserial bearing of without inner ring of needle bearing,and directly adopts bearing outer ring as shock wave thimble;Center wheel of two-stage reduction gear and center wheel of two-stage reduction gear passes through taper thread,and center wheel is fixed;As soon as the flange of input end and center wheel of one-stage reduction gear,the flange of export end and center wheel of two-stage reduction gear makes monobloc structure.

本文设计的井下减速器的传动均采用活齿传动，一级减速器的输出轴和二级减速器的输入轴通过花键联轴套联接；激波环与活齿的连接方式采用能承受较大载荷的无内圈双列滚针中国财经圈，中国财经圈，且直接采用进口中国财经圈外圈作为激波环；一级减速器的中心轮和二级减速器的中心轮是通过锥螺纹连接的，且中心轮固定；一级减速器的中心轮与输入端的法兰盘，二级减速器的中心轮与输出端的法兰盘均做成整体的结构。

In view of this fault features discussed judgment is that the main motor brake problems more likely, as a result, and then by careful observation, he finally found Braker friction wheel in closing the gap between the time of separation are uneven, there was a slight touch of local sweep／ to the corresponding axis on the spindle motor, which enables some resistance.

鉴于这一障碍特点，笔者开端鉴定是宾电机制动器呈现题目的不定性较大，于是，再通功不苛的查察，毕竟发掘制动器上的摩擦轮在呼分别离时的间隙有不平均不梢体，部分有惨重碰擦到对应的轴轮上，这样使电机宾轴爆发必定的阻力。

The smaller piston is incorporated internally of the output shaft, while the larger piston, of an annular shape, coaxially surrounds the output shaft.

较小的活塞（58）被设在输出轴（16）内部，而较大的活塞（68）呈一环形形状，其同轴地环绕输出抽（16）。

The measured radiation patterns of the mode coveter agree well with the calculated results, which indicate that the out-put modes of the mode converter are the same as the simulated results.

实验测得模式转换器的辐射方向图轴向最大，与数值计算结果吻合良好，表明实验中模式转换器的输出模式与数值计算结果一致，从而验证了同轴插板式模式转换器的可行性。

According to the calculated result, the metal flowing law, von Mises stress and the formed outer diameter of involute spline were forecasted; also the errors between the simulation result and the object dentiform of involute spline were analyzed.

根据数值模拟的结果，讨论了齿形误差及其成因；揭示了滚轧过程中金属流动规律和应力变化情况；分析了冷滚轧前轴坯直径与成形后花键最大外径的关系，提出了轴坯直径的修改建议。

Based on an analysis of distribution pattern of hydrocyclone"s axial velocity, by changing the inlet flow rate Qi and split ratio Fand making an investigation in the effect of Qi and F on axial velocity field, the factors causing the forming of short-cut circuit and circulating flow are found. It is considered that the short-cut circuit and circulating flow are produced by the structure of the hydrocyclone, and can"t be eliminated completely, though they interfere the flow field inside a hydrocyclone and affect the separation accuracy. Test results show that, by increasing Qi and F and controlling them in a certain range, the separation efficiency of the hydrocyclone can be improved.

在研究旋流器轴向速度分布规律的基础上，分析了短路流与循环流的形成原因，试验研究了改变操作参数，即改变入口流量Qi与分流比F对轴向速度场的影响认为短路流与循环流是由旋流器结构决定的，很难完全消除，它们干扰了旋流腔和大锥段的流场，在一定程度上也影响了分离精度试验结果表明，加大入口流量Qi与分流比F，并将其控制在一定范围内，便可提高分离效率这项研究对水力旋流器分离机理的认识与实际应用均有重要意义

At present, all the P-Y curve methods recommended by the referring code demand using geotechnic parameters C_u (three-axle undrained shear strength) and ε_50(the strain value that is equal to a half of the difference stress in the undrained triaxial compressing test). Moreover, we must do the complex and expensive triaxial geotechnic experiment to get those two geotechnic parameters, so they restrain the P-Y curve method from using comprehensively.

但目前国内外有关规范推荐的P-Y曲线均需用到土工参数C_u和ε_(50)(三轴不排水压缩试验中最大主应力差一半时的应变值)，而获得这两个参数需要进行比较复杂且费用较高的土工三轴试验，限制了P-Y曲线法的广泛应用。

Bamboo first crystallizes then lignifies during bamboo shoot growth and basically forms crystal structure in one month. 1-year-old bamboo culm ends growth and its height,thickness, volume almost change little, but culm tissue is small and tender and there is more water and less substance in it. Bamboo crystal proportion keeps invariable during this period.2-year-old bamboo culm begin to lignify,its cellulose proportion debases and its crystal proportion decreases. Bamboo lignin debases, crystal proportion changes a little in the end of this period.Many-old-year bamboo culm crystal proportion is almost invariable. Freaky bamboo cell wall crystal region's thickness is less than normal bamboo's. Bamboo cross section crystal area and the ratio of long axis to short axis are less than normal bamboo's,and roundness,irregular index, the fiber cap density per unit area increase more than normal bamboo's.

竹笋生长阶段是先结晶后木素化的过程，一个月内细胞壁结晶组织基本形成；2）一年生竹材的植株秆茎生长结束，秆茎的高度、粗度和体积变化不大，但秆茎的组织幼嫩，含水量高，干物质少，竹材结晶度基本不变；3）二年生竹材的植株开始木质化，纤维素比例降低，结晶度减少，到后期竹子木质化降低，竹材结晶度变化不大；4）多年生竹材的结晶度没有太大的变化，结晶度大小处于波动状态；5）畸形竹材纤维帽细胞壁结晶区的厚度比正常竹小，其横截面结晶区的面积、纤维帽长轴与短轴比有所减少，而圆形度、异型指数有所加大，单位面积纤维帽的密度增大。

The displacement is large when the load is exerted mesiodistally or buccolingually, and decrease slowly along the long axial of implant. While the load is exerted gingivooccluaslly, the displacement is very small and change gently.

前两者位移量较大，并沿植入体长轴缓慢递减，而后者的位移量非常小，并沿植入体长轴的位移变化也非常小。

Breath, muscle contraction of the buttocks; arch body, as far as possible to hold his head, right leg straight towards the ceiling (peg-leg knee in order to avoid muscle tension).

呼气，收缩臀部肌肉；拱起身体，尽量抬起头来，右腿伸直朝向天花板（膝微屈，以避免肌肉紧张）。

The cost of moving grain food products was unchanged from May, but year over year are up 8%.

粮食产品的运输费用与5月份相比没有变化，但却比去年同期高8％。