大轴

After serious corrosion for main axis of naval vessel in sea water, the corrosion region of the main axis was restored by using adhesively bonding technology and domestic high strength metallic healant.

舰艇大轴在海水中严重腐蚀后，采用粘接技术，选用国产高强度金属修补剂，对大轴局部腐蚀部位进行修理，对提高大轴使用寿命，防止大轴再腐蚀起到有效作用。

Large vessels with large-axis value of expensive bearings used in place there will be wear and tear, can not be used, TG using thermal spray technology shaft to restore the normal size, so that shaft back to life for the users save the cost of the replacement parts, created a value!

大型船舶用大轴价值昂贵，使用中会出现轴承位磨损，无法使用，徐州天工采用热喷涂技术恢复了大轴正常尺寸，使大轴起死回生，为该用户省去了换新件的费用，创造了价值！

Using Latin square test, the effect of geometrical parameters on the characteristics of non-overload sewage pump was studied, and the effecting principle of geometrical parameters on efficiency, maximum brake horsepower and its location were researched, the major and minor factors affecting these performance were found out by way of variance analysis, the correction of equation on maximum brake horsepower and its location were also tested.

用正交试验法研究了各几何参数对无过载排污泵性能的影响，探索了各几何参数对效率、最大轴功率值及其位置的影响规律，并通过方差分析找到了影响这些性能的主要因素和次要因素，验证了无过载排污泵最大轴功率值及其位置公式的正确性，根据试验结果对模型泵提出了进一步设计方案，本试验结果对无过载排污泵水力设计有一定的参考价值。

This is a rotation of the windmill, by the three major axis and the axis composed of three small windmill, and into a clockwise rotation, the center of the color change cycle.

详细说明：这是一个旋转的风车，由三个大轴和大轴上的三个小风车组成，且成顺时针转动，中心的颜色成周期变化。

Based on existing creep theory and the spline function collocation point method, a numerical method was developed to calculate the transient creep strain and stress of a rotor of steam turbine to be aligned.

以往由于缺乏转子钢在直轴温度范围内的蠕变特性实验数据以及对大轴温度场、应力场和应变场的深入理论分析，直轴工艺还带有较大的经验性。

The calculations of torsional vibration of crankshaft systems of 12V240ZJ6E diesel engines were carried out with TVCA programme and I deas software to obtain system natural vibration frequencies, vibration amplitudes of various concentric masses at different rotational speeds, and torques and torsional stress es of various crankshaft sections at different rotational speeds.

运用TVCA程序和Ⅰ deas软件对 12V2 4 0ZJ6E型柴油机轴系的扭转振动进行计算，求出系统的自振频率、各集中质量在不同转速下的振幅和各轴段在不同转速下的扭矩、扭转应力值，对自振频率、自由端振幅和扭转应力最大轴段进行了分析，对轴系的扭转振动情况作出总结与评

The greatest quality of axle load: vehicle carrying the largest single-axis by the total mass.

最大轴载质量：汽车单轴所承载的最大总质量。

A APDL program is developed for analyzing the contact stress of journal bearing pair of roller cone bit. The 25 contact stress cases of different clearance fit(including clearance of large bearing is bigger, equal to and smaller than that of small bearing) journal bearing pair of the 8 1/2XXX roller cone bit are analyzed. The result is that the maximum contact stress is less when the clearance of large journal bearing pair is smaller than or equal to that of small journal bearing pair.

用参数化设计语言APDL编制了牙轮钻头滑动轴承的ANSYS接触有限元分析程序，根据钻头制造厂方提供的某8 1/2的轴承配合间隙尺寸，分三种不同的间隙配合（大轴间隙大于小轴间隙、大轴间隙等于小轴间隙、大轴间隙小于小轴间隙），共25种情况，对轴承的表面的接触应力进行了分析，得出：大轴间隙小于等于小轴间隙时最大应力比较小。

The effects of such parameters as temperature, pH, feeding rate,concentration, [NH_3]_T/_T molar ratio, surfactants and agitation, on the morphology and size of the particles, were studied and conclusions obtained are as follows:(1) The morphology and size of the particles are mainly decided by the species of nickel oxalates present.(2) Speeding up dissolution-recrystallization process benefits the preparation of the particles of being composed of a single species with uniform morphology and high aspect ratio.(3) The variations of nucleation and growth supersaturation under different conditions have definite effects on the morphology and size of the particles.(4) Adding PVP25 at a proper amount is beneficial to the preparation of fibrous nickel oxalate particles with high aspect ratio. 3 The formation mechanism as well as the morphology and size control of fibrous cobalt oxalate particlesThe cobalt oxalate particles with fibre morphology were prepared using CoCl_2 solution and mixed(NH_4)_2C_2O_4, NH_3·H_2O solution by a double jet process.

研究了温度、pH值、加料速度、浓度、[NH_3]_T/_T摩尔比、表面活性剂及其添加量、搅拌等对颗粒形貌与粒度的影响，主要结论为：(1)草酸镍化合物种类是决定颗粒形貌与粒度的最主要因素；(2)提高陈化中溶解—再结晶速度，有利于得到物相单一，形貌规整，轴向比大的粉末；(3)不同条件下，颗粒形核与生长过饱和度改变，也会对粉末形貌与粒度产生一定影响；(4)适量添加PVP25有利于大轴向比纤维状草酸镍的制备。3纤维状草酸钴的形成机理及其形貌与粒度控制采用CoCl_2溶液与(NH_4)_2C_2O_4和NH_3·H_2O混合溶液并流加料合成的方法，研究了纤维状草酸钴的制备。

RESULTS:① The maximal axial pulling-out force of 10 femoral neck samples implanting the hollow nail was 471.5-1 070.5 N, with the mean value of (855.0±207.5) N; the maximal axial pulling-out strength of femoral neck samples implanting the side-hole hollow nail added by poly-methyl methacrylate bone cement was 2 023.7-3 572.1 N, with the mean value of (2 943.3±535.8) N.

结果：①置入空心钉10个股骨颈的最大轴向拔出力为471.5~1 070.5 N，平均(855.0±207.5)N；而添加聚甲基丙烯酸甲酯侧孔空心钉后最大轴向拔出力在2 023.7~3 572.1 N，平均(2 943.3±535.8)N。

Lugalbanda was a god and shepherd king of Uruk where he was worshipped for over a thousand years.

Lugalbanda 是神和被崇拜了一千年多 Uruk古埃及喜克索王朝国王。

I am coming just now,' and went on perfuming himself with Hunut, then he came and sat.

我来只是现在，'歼灭战perfuming自己与胡努特，那麼，他来到和SAT 。