多孔的

But when the cholesterol was substituted by its oxide result, the membrane life time extended to nearly 60 hrs ;besides the diameter of the hole on which the membrane exists 、temperature、PH value cause great effects to the life time of the membrane, and the diameter was the most important element. When the diameter larger than 3mm it is almost no way to form a membrane on the hole under experiment condition. Between 1mm and 3mm it has a better result by change the prescription of the membrane. when it is 0.5mm all the membrane can last more than 40 hrs ,and the prescription like Och : phosphatidylcholine / cephalin＝4:1; 3:1; 2:1; 1:1; 2:3 need the request of the experiment basically, when cooperate with multi hole structure it is very to detect the concentration and found the model.

研究结果说明，成膜在普通胆固醇/磷脂配方下不能达到满意的结果，无论如何改变外界条件成膜始终超不过7小时，而将胆固醇换成氧化胆固醇再和磷脂按照一定配比的时候，成膜时间则大大延长，可达60h左右；另外除成膜配方，成膜孔径、温度、PH值等因素对成膜有着很重要的影响，成膜孔径对膜的影响最为关键，在3mm以上的孔径时成膜比较困难，在1－3mm适当提高成膜液浓度可以改善，孔径为0.5mm左右成膜比较稳定基本都能达到40h以上，合适的几个配方如卵/脑磷脂：氧化胆固醇＝4：1；3：1；2：1；1：1；2：3基本满足实验要求，配合一板多孔结构，可以保证单位时间的离子传输量的检测和计算。

Based on the item of national high technology development project, the thesis studies the reasonable construction pattern of the tunnel portal, incidence of the micro-pressure wave and the the effect of bell-mouthed hood, lacunaris hood and expansile hood on alleviating the micro-pressure wave in the situations of single line and double line, obtains the relationship between the max micro-pressure wave and the velocity of the train as well as the relationship between the max micro-pressure wave and distance of measuring point at the velocity of 100km/h-550km/h, compares the different alleviative effect of the three different hood to max micro-pressure wave and finally proposes the reasonable construction pattern of the tunnel portal.

本文针对国家高技术研究发展计划(863计划)课题"磁浮交通沪杭线越黄浦江隧道的工程技术问题研究"，在单洞单线和单洞双线两种工况下，对隧道洞口的合理结构形式和影响范围，以及洞口喇叭形入口缓冲段、多孔壁入口缓冲段以及隧道出口膨胀室对减缓微压波的作用进行了研究，得到了磁浮列车速度在100km/h～550km/h时隧道出口微压波最大值与速度的关系以及微压波最大值与测点距离的关系，比较了三种不同形式缓冲结构对微压波最大值的减缓效果，提出了隧道洞口的合理结构形式。

Metamorphic protein element can condense into a skin, form very firm film to surround the air of interfuse inclose, in the meantime, as a result of the action of exterior tension, make albumen bubble contractive become globose, add albumen colloid to have viscosity and affiliation flour raw material to adhere to it is all round albumen bubble, make bubble becomes very stable, can carry the gas of interfuse, in heating process, the gas inside bubble be heated expands, make goods loose and poriferous and have certain flexibility and tenacity.

变性的蛋白质分子可以凝聚成一层皮，形成十分牢固的薄膜将混入的空气包围起来，同时，由于表面张力的作用，使得蛋白泡沫收缩变成球形，加上蛋白胶体具有黏度和加入的面粉原料附着在蛋白泡沫四周，使泡沫变得很稳定，能保持住混入的气体，加热的过程中，泡沫内的气体又受热膨胀，使制品疏松多孔并具有一定的弹性和韧性。

Migration of radioactive nuclides in groundwater of porous media is controlled not only by groundwater hydraulics, but also by many other physical, chemical processes. Nuclides transport model coupled chemical equilibrium action is to join convection-dispersion model and multicomponent chemical equilibrium model, it is different from traditional transport model based on K〓 completely in theory.

地下水中核素在多孔介质的迁移过程不仅受到水动力的控制，还受到多种物理化学作用的影响，耦合平衡化学作用的核素迁移模型就是把对流—弥散模型与多组分化学平衡模型有机地结合起来，这种模型与传统的基于K〓值的核素迁移模型在理论上是完全不同的。

Recites passive cooling technology methods of buildings, describes the structure of each cooling methods and compares its performance, in the same time, summarizes passive cooling technology methods of buildings fit for drought and torridity area, introduce basal principle of moisture-conditioned material, new pattern porosity moisture-conditioned material Used in buildings, recommend the structure and transfer principle of this material.

从叙述建筑物被动冷却方式入手，对各种冷却方式的结构特征进行了描述和性能比较，同时总结了适用于干热地区环境因素的建筑物被动冷却方式，并重点介绍了近年来迅速发展应用的调湿材料的基本原理，提出了一种新型的用于贴附于建筑物墙体外表面的多孔调湿材料，简述了这种材料的结构特征及内部的传递机理。

Inthe last stage of reduction,the iron substrates formed on the surface of Wüstite areporous and permeable to gaseous diffusion.The reduction rate is controlled by thesurface reaction on the Wüstite-iron interface,but the rate of this surface reactionis limited by the velocity of CO formation.

在浮士体还原成金属铁的阶段，所生成的多孔性金属铁并不阻碍气相的扩散；还原的速率由浮士休-金属铁相界面的表面反应所控制，而表面反应的速率则受CO的生长速率所限制。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,代写医学论文,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对冷冲压技术的分类、特点及发展方向作了简略概述；论述了冲压零件的形成原理、基本模具结构与运动过程及其设计原理；对典型的冲压件模具进行了设计：大直径三通管冲压复合模设计盖世了大直径三通管的加工困难的问题、带有浮动凸凹模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、消音器后补碗落料、拉深、冲孔、翻边复合模设计、一模两件落料拉伸冲孔翻边复合模设计、环形弯曲件的模具设计、铰链卷圆成形工艺及模具设计、半自动送料切角装置设计、滑板式送料拉深、冲孔、翻边模设计实现自动送料、长管多孔冲模设计、带凸缘台阶方盒形零件拉深模和盒形件侧壁小孔翻孔模。

Elaborated the punching components formation principle, the basic dies structure and the rate process and the principle of design; and designed some conventional punching die:the die for big diameter three direction pipe which solved the problom of traditional machining,the drawing and punching compound die with float punch-matrix,the drawing and cutting compound dies with unaltered press,the compound die for the back bowl of the noise keeper,the design of the compound die which could produce two workpieces in one punching,the bending die for the ring shape part ,the bending die which used the gemel ,automate loading die for cutting, the drawing,punching and burring compound dies with sliding automated loading,the punching die for the long pipe with two row of hole,the drawing die for the square box shape workpiece and the burring die for the box shape workpiece.

本文对冷冲压技术的分类、特点及发展方向作了简略概述；论述砬冲压零件的形成原理、基本模具结构与运动过程及其设计原理；对典型的冲压件模具进好的了设计：大直径三通管冲压复合模设计盖世了大直径三通管的加工难题、带有浮动凸凹模的拉伸冲孔复合模设计、适力压边式落料拉伸切边复合模设计、消音器后补碗落料、拉深、冲孔、翻边复合模设计、一模两件落料拉伸冲孔翻边复合模设计、环形弯曲件的模具设计、铰链卷圆成形工艺及模具设计、半自动送料切角装置设计、滑板式送料拉深、冲孔、翻边模设计实现自动送料、长管多孔冲模设计、带凸缘台阶方盒形零件拉深模与盒形件侧壁小孔翻孔模。

According to the phase change law for wax deposition and dew point line curves, and the change of the saturation of condensate gas with phase properties, gas-liquid-solid was transformed with phase change, which would result in the change of distribution of fluid pressure and influence or alter the characteristic and the process of condensate gas percolation flow.

根据相的变化受析蜡线、露点线的相态变化规律控制，分析相变特性会导致储层内油气饱和度的变化，揭示蜡沉积在多孔介质表面引起孔隙性质改变和气、液、固在储集层中的微观空间分布会影响凝析气的流动特征。

The wonderful loess lands, which cover much of Kansu, Shensi, Ninghsia, and Shansi provinces, account for the marvelous fertility of these regions, for the loess furnishes an inexhaustible porous topsoil tens of feet deep.

这一令人惊叹的黄土地带，广及甘肃、西、夏、西四省的大部分地区，雨量充分的时候异常肥沃，因为这种黄土提供了无穷无尽的、几十英尺深的多孔表土层。

I can not make it blossom and suits me

我不能让树为我开花

When temperatures are above approximately 80 °C discolouration of the raceways or rolling elements is a frequent feature.

当温度高于 80 °C 左右时，滚道或滚动元件褪色是很常见的特征。