外径

On qualitative examination, no dilations, brittleness, obstruction, nodularity, tears, loss of elasticity, color changes, tube fracturing, kinking, loss of resilience, or variation in external diameter was observed.

定性检测方面，没有观察到PEG管扩张，变脆，闭塞，结节，裂伤，弹性丧失，颜色改变，管子断裂，丧失回弹性，内径和外径的改变等。

On qualitatie examination, no dilations, brittleness, obstruction, nodularity, tears, loss of elasticity, color changes, tube fracturing, kinking, loss of resilience, or ariation in external diameter was obsered.

定性检测方面，没有观察到PEG管扩张，变脆，闭塞，结节，裂伤，弹性丧失，颜色改变，管子断裂，丧失回弹性，内径和外径的改变等。

Japan Mitutoyo: caliper, test indicator, internal/external indicator, dial micrometeer, pin gauge, height meter, dial height tester, microscope, microminiature measure head etc.....

日本三丰（Mitutoyo：卡尺，百分表，内/外径千分表，三爪数显千分尺，针规，高度尺，数显高度仪，测量显微镜，微分头等。

The effects of structural parameters of liner and initiation methods on projectile formation and performance parameters were shown by simulation, the interrelations of structural parameters of liner were preliminarily fixed on, the inner radius of liner R1=(0.55-0.6)D, outer radius R2=(0.58-0.62)D, height H=(0.3-0.35)D, half cone angle α=82°-86°, where D is diameter of liner.

通过模拟计算得到了药型罩结构参数和起爆方式对弹丸成型的影响规律，并初步确定药型罩结构参数间的相互关系：药型罩直径D，内径R1=(0.55~0.6)D，外径R2=(0.58~0.62)D，药型罩高度为H=(0.3~0.35)D，半锥角α=82°~86°。

The first direct measurement with micrometer piston skirt and the outside diameter Do micrometer stop screw to the locking plate position, and then dial indicator card installed and well well inserted under the initial installation of the amount of cards, directly into the cylinder corresponding cylinder kit, adjust the volume of the cylinder rod out in table inserted length, so that small hands dial indicator cell has about 1 volume of pre-press and lock locking rod inserted mother, at the same time, large dial indicator dial to adjust zero, the last cylinder to adjust the volume of good form under test card inserted rods and do at Anvil micrometer and measured the rod between the big hands dial indicator at this time than the "zero" high value is the piston and cylinder liner with the space.

3先直接用千分尺测量活塞裙部的外径并将干分尺止动螺钉扳转到锁紧位置，再将卡装好百分表和初步安装好插杆的量缸表直接卡入对应气缸套内，调整量缸表插杆的伸出长度，使百分表的小表针有1格左右的预压量并锁紧插杆锁母，同时将百分表的大表盘调整到零，最后将调整好的量缸表的测杆和插杆卡在干分尺的砧座和测杆之间，此时百分表大表针比&零&高的数值即为活塞和气缸套的配合间隙。

The first direct measurement with micrometer diameter piston skirt, and then dial indicator card installed and the initial installation of the amount of good cylinder rod inserted card table micrometer mounted on the anvil between the seat and the measuring bar, adjust the volume of cylinder table Interpolation of the extended length of rod, when the dial indicator has small hands around 1.5-2 cell volume preloading lock locking rod inserted mother, and a large dial indicator to zero adjust the final stretch to the volume of cylinder table into the Cylinder Sleeve, large dial indicator hands than "zero" low value (considering the small hands reading) is the piston and cylinder liner with the space.

2先直接用千分尺测量活塞裙部的外径，然后将卡装好百分表和初步安装好插杆的量缸表卡装在千分尺的砧座和测杆之间，调整量缸表插杆的伸出长度，当百分表的小表针有1.5-2格左右的预压量时锁紧插杆锁母，并将百分表的大表盘调整到零，最后将量缸表伸入气缸套内，百分表大表针比&零&低的数值即为活塞和气缸套的配合间隙。

SEM and DLS analyses reveal that the particle size of the hollow particles increases with the increasing concentration of the iron chloride and the reaction temperature as well. TEM analyses indicate that the shell thickness is increased with the reaction temperature.

另外，SEM与DLS结果显示提高氯化铁浓度及反应温度皆会使中空球的外径增加；TEM证实反应温度提高，壳层厚度有增厚的趋势。

This article introduced application of digital laser vision technology in several key links during welded pipe manufacturing,including realizing weld tracking,adaptive adjusting welding parameters or angle of driving the strip, measuring coil plate width and edge contour,measuring steel pipe diameter,and automatic inspecting weld profile and defects,etc..

介绍了数字激光视觉技术在焊管制造过程中多个关键环节中的应用，包括实现焊缝跟踪，焊接参数或钢带送进角度的自适应调整，钢板宽度与边缘形状的检测，钢管外径的测量，焊缝成形及缺陷的自动检测等。

Ex-mark Protection Cable,s outside Inlet,s thread Lamp socket Mass

防爆标志防护等级电缆外径进线口螺纹灯座代号质量kg

And the bearing outside diameter relative largening 607ZZ, steel ball diameter is increased, the number increases under torsion, smooth running in June of last year, we decorate heifei rongshida industrial co., Ltd. packaging branch of the two production lines (2.2M 1.8M) have done.

而607ZZ轴承外径相对加大，钢珠直径也相应加大，粒数也有所增加，承受扭力大，运转平稳在去年的6月份，我们对合肥荣事达工业包装装潢有限责任公司包装分厂的两条生产线（2.2M 1.8M）做了改造。

The split between the two groups can hardly be papered over.

这两个团体间的分歧难以掩饰。

This approach not only encourages a greater number of responses, but minimizes the likelihood of stale groupthink.

这种做法不仅鼓励了更多的反应，而且减少跟风的可能性。