复相的

By analyzing the educt and oxide of 〓 powder and BN powder, it is foundthat residual inside the composite is the main cause for the deliquescence of thecomposite and that the boron oxide mainly comes from the BN.

添加烧结助剂，既有效地促进了样品中导电网络的构成，又对〓-BN复相导电陶瓷的电阻率产生很大影响，而且〓配比越接近渗流阀值，烧结助剂的影响越大。

In addition, we also discussed the effect of the granularities of the powders and the added phases on the mechanical properties of the alumina-based diphase ceramics.

另外本文还讨论了原料粉末的起始粒度和添加相对氧化铝基复相陶瓷的影响。

Using diphase emulsion to make bovine albumin microcapsuals with hydroxy proprl methyl celluloxe phthalate and CMC-Na,Gelatine,chitosan as dispersed phase;Designing test with single factors method and studying effection of the wrap material,reagent of emulsification,hydrophilic colloid of protection...

分别用羧甲基纤维素钠、明胶、壳聚糖作分散质，复相乳液法制备HPMCP的BSA微胶囊；采用单因子设计试验，研究了壁材、乳化剂、分散质浓度对微胶囊包裹量的影响。

Using diphase emulsion to make bovine albumin microcapsuals with hydroxy proprl methyl celluloxe phthalate and CMC-Na, Gelatine, chitosan as dispersed phase; Designing test with single factors method and studying effection of the wrap material, reagent of emulsification, hydrophilic colloid of protection on the methods for testing the protein envelopment quantum of HPMCP Microcapsuals.

分别用羧甲基纤维素钠、明胶、壳聚糖作分散质，复相乳液法制备HPMCP的BSA微胶囊；采用单因子设计试验，研究了壁材、乳化剂、分散质浓度对微胶囊包裹量的影响。

BN composite has a great application potential owing to its machi...

〓-BN复相导电陶瓷具有优良的机加工性和方便的电性能可设计性等，其应用前景十分广阔。

And 4. 8%, respectively, in prestrain 6% and which indicates the remarkable improvement of the shape memory completeness.

本文研究低层错能Fe基合金在复相状态下的形状记忆效应，具有重要的创新意义和生产应用背景。

Friction and wear behaviors were studied for Ti_3SiC_2/SiC multiphase ceramics/45 steel pairs under unlubricated and lubricated.

研究了由热等静压原位合成的Ti3SiC2/SiC复相陶瓷与45#钢在干摩擦和边界油润滑条件下的摩擦磨损特性。

Friction and wear behaviors were studied for Ti_3SiC_2/SiC multiphase ceramic s/45 steel pairs under unlubricated and lubricated.

研究了由热等静压原位合成的Ti3SiC2/SiC复相陶瓷与45#钢在干摩擦和边界油润滑条件下的摩擦磨损特性。

The results show that the oxidation efficiency of sulphide can be reached to 91.2%by using WO3/α-Fe2O3/W as heterogeneous photocatalyst, with quantity of catalyst =0.300g/50ml, pH=8～8.1, starting concentration of sodium sulphide=19.00～21.00mg/l, illumination time=7h.

试验结果表明：采用WO3/α-Fe2O3/W为复相光催化剂，当其用量为0.300g、pH=8.0～8.1、硫化物的浓度为19.00～21.00mg/l时，光照7h硫化物的氧化率达到91.2%。

The experimental verifications show that the theoretical calculation of fracture toughness is well in agreement with the measured toughness.

详细研究了复相陶瓷刀具材料JX-2-Ⅰ的界面力学行为及其与材料力学性能的关系。

This paper discusses design and realizable methods of remote test output interface from logical design angle.

本文从逻辑设计的角度讨论遥测输出接口的设计及实现方法。

This also 星体投射plies to buildings, structures and geological features.

这也适用于建筑物和地质特征。